FORD WSS-M1H812-A-2015 FABRIC MALAGA PATTERN KNIT TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSS-M1H812-A-2015 FABRIC MALAGA PATTERN KNIT TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M1H812-A-2015 FABRIC MALAGA PATTERN KNIT TO BE USED WITH FORD WSS-M99P1111-A .pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2015 12 09 N Status No replacements D. Murtonen, NA 2003 02 26 Revised Para 3.0 inserted ; Para 3.1, 3.2, 3.3, 3.11, 3.12, 4 deleted 1999 08 06 Activated R. Cyrillo Neto Page 1 of 3 Copyright 2015, Ford Glob

2、al Technologies, Inc. FABRIC, MALAGA PATTERN, KNIT WSS-M1H812-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a knit body cloth of good quality and uniform composition. 2. APPLICATION This specification was released originally for material used as an interior t

3、rim fabric for seating fabric. 3. REQUIREMENTS In addition, to the requirements listed herein, the fabric shall meet all requirements of WSS-M8P18-A1/A4 as applicable. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requi

4、rements For Production Materials (WSS-M99P1111-A). 3.4 FABRIC CONSTRUCTION 3.4.1 Fabric Count, +/- 5 % tolerance (ASTM D 3887) Wales 18.0 wales/cm Courses 11.0 courses/cm 3.4.2 Fabric Weight, range 210-245 g/m2 (FLTM BN 106-01) 3.5 COMPOSITION (ASTM D 629) Tolerance as specified in WSS-M8P18-A1/A4 F

5、abric 100% polyester ENGINEERING MATERIAL SPECIFICATION WSS-M1H812-A Page 2 of 3 Copyright 2015, Ford Global Technologies, Inc. 3.6 YARN CONSTRUCTION (ASTM D 1244) Face 110 dtex f30 (polyester, semi-dull, texturized, grey) Middle 167 dtex f30 (polyester, semi-dull, texturized, grey) Back 75 dtex f30

6、 (polyester, semi-dull) 3.7 METHOD OF DYEING Yarn dyed, or as approved by Materials Engineering. 3.8 FINISHING OPERATIONS As approved by Materials Engineering. 3.9 FLAMMABILITY (ISO 3795/SAE J369) Burn Rate, max 100 mm/minute Note: Not required on face fabric when used as a fully bonded composite. 3

7、.10 STRETCH & SET, %, range (SAE J855) Fabrics outside this range may be accepted provided they have been approved jointly by the Materials Engineering activity and the affected Design Engineering and Development activity. Wales Courses Stretch, range 6 - 30 10 - 35 Set, max* 12 14 * At no time shal

8、l the set exceed 40 % of the measured stretch unless approved jointly by the Materials Engineering activity and the affected Design Engineering and Development activity. ENGINEERING MATERIAL SPECIFICATION WSS-M1H812-A Page 3 of 3 Copyright 2015, Ford Global Technologies, Inc. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 Purchase departments will ensure that both materials defined in this specification and shipped to any one assembly plant will be produced by one supplier only.