FORD WSS-M1H1299-A11-2018 FABRIC MARL LIGNE FLAT WOVEN 100% VIRGIN WITH SOIL REPELLANT TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSS-M1H1299-A11-2018 FABRIC MARL LIGNE FLAT WOVEN 100% VIRGIN WITH SOIL REPELLANT TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M1H1299-A11-2018 FABRIC MARL LIGNE FLAT WOVEN 100% VIRGIN WITH SOIL REPELLANT TO BE USED WITH FORD WSS-M99P1111-A .pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2018 02 09 Released R.Kyle ,EU Controlled document at 0www.MATS Copyright 2018 Ford Global Technologies, LLC Page 1 of 2 FABRIC, MARL LIGNE, FLAT WOVEN, WSS-M1H1299-A11 100% VIRGIN WITH SOIL REPELLANT 1. SCOPE The material defined by t

2、his specification is an embossed flat woven polyester face fabric made from 100% virgin yarn. 2. APPLICATION This specification was released originally for material used as an interior trim fabric for 2018 MY seat insert. The fabric was originally approved as tri-laminated with foam and a backing sc

3、rim. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located wi

4、thin Ford at or available externally through a Ford Materials Engineer. 3.2 APPPEARANCE The color, pattern, and finish shall match the approved Corporate Design master sample. 3.3 FABRIC PERFORMANCE In addition to the requirements listed herein, the fabric shall meet all requirements of WSS-M8P18-B

5、1/B2/B3/B4/latest as applicable. 3.4 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity. Testing of the material should occur in the conditioning environm

6、ent or soon after removal. 3.5 FABRIC CONSTRUCTION 3.5.1 Fabric Count, - /+ 5% tolerance (ASTM D3775) Warp 278 / 10 cm Weft 300 / 10 cm 3.5.2 Fabric Weight, -/+5 % tolerance 235 g/m2 (FLTM BN 106-01) 3.6 COMPOSITION (ASTM D629) Fabric 100% polyester ENGINEERING MATERIAL SPECIFICATION WSS-M1H1299-A11

7、 Copyright 2018, Ford Global Technologies, LLC Page 2 of 3 3.7 YARN CONSTRUCTION (ASTM D1244) Warp 350 Dtex f92 (Semi-dull, false twist , marl) Weft 350 Dtex f92 (Semi-dull, false twist, marl) 3.8 METHOD OF DYEING Piece dyed / Solution Dyed 3.9 FINISHED OPERATIONS drying, Pad SR, Stenter finish , la

8、minate, emboss Any changes to the above process must be approved by Materials Engineering. 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifi

9、cations. 4.1 Purchase departments will ensure that the material defined in this specification and shipped to any one assembly plant will be produced by one supplier only. In the event of a Global Program or Regional duplication, each regional location of the supplier for this specification must prov

10、ide a Construction package and be approved to meet this specification. 4.2 If yarn is locally sourced it must meet the above fabric construction, composition and yarn construction. The fabric must also meet the requirements of WSS-M8P18-B1/B2/B3/B4/latest. 4.3 Global strategy for this fabric is to u

11、se tri-laminate/foam & scrim construction in all regions. 4.4 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Product Development, and Materials Engineering. The supplier shall submit a completed copy of the

12、ir laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material Specification. Tested material samples must be available for review upon request and kept for a minimum of one year. Upon requ

13、est, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. 4.5 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalent in all characteristics to the material upon which approval was ori

14、ginally granted. Prior to making any changes to the material originally approved, whether or not such changes affect the materials ability to meet the specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activit

15、ies of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SREA. For parts and components using Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and P

16、roducation Part Approval Process (PPAP) sign off must be kept until Job 1. ENGINEERING MATERIAL SPECIFICATION WSS-M1H1299-A11 Copyright 2018, Ford Global Technologies, LLC Page 3 of 3 4.6 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A/latest which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis. 5. SUMMARY OF REVISIONS