FORD WSS-M1C226-A3-2017 GREASE PETROLEUM TRANSMISSION PORT PLUGGING TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSS-M1C226-A3-2017 GREASE PETROLEUM TRANSMISSION PORT PLUGGING TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M1C226-A3-2017 GREASE PETROLEUM TRANSMISSION PORT PLUGGING TO BE USED WITH FORD WSS-M99P1111-A .pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2017 07 26 Released S. Ryzyi and N. Jost, NA Controlled document at www.MATS Copyright 2017, Ford Global Technologies, LLC Page 1 of 2 GREASE, PETROLEUM, TRANSMISSION PORT PLUGGING WSS-M1C226-A3 1. SCOPE The material defined by this sp

2、ecification is a petroleum based, lithium soap thickened grease. 2. APPLICATION This specification was released originally for grease used to seal plastic shipping plugs into the ports of automatic transmissions to prevent leakage of residual fluid. Grease approved to this specification has the pote

3、ntial to be used in other applications, but this specification does not serve to qualify the material or performance for other applications. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL

4、) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford at or available externally through a Ford Materials Engineer. The material specification number may be used as the part number for Ford purchasing. The a

5、pproved source for this specification is: Supplier: Chemtool Incorporated (GSDB: C409C) Product Name: MC 2044NBF NA Tox # 136426. 3.2 COLOR Amber (Visual) 3.3 UNWORKED PENETRATION, tenths of a millimeter 195 225 (ASTM D217, 0 stroke) 3.4 DROPPING POINT 177 C min (ASTM D566, ASTM D2265, DIN ISO 2176)

6、 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 OIL SEPARATION DURING STORAGE 3% max (ASTM D1742, DIN 51817 or FTMS 791 C 321

7、.3) 4.2 OIL SEPARATION FROM GREASE 1% max (ASTM D6184, 24h, 100C) ENGINEERING MATERIAL SPECIFICATION WSS-M1C226-A3 Copyright 2017, Ford Global Technologies, LLC Page 2 of 2 4.3 INTERFACE COMPATIBILITY Compatibility testing was not performed and there are no known compatibility issues in this applica

8、tion. The grease interfaces with the aluminum housing, the polyethylene plug (ATSM D4000 PE113), and the transmission fluid (WSS-M2C949-A). Any changes to the grease should be reassessing for the application. 4.4 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain

9、 an expression of interest from Purchasing, Design or Product Development, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requ

10、irements of the Material Specification. Tested material samples must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testi

11、ng) with Ford. 4.5 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved, whether or not such changes affect the materials ability to meet th

12、e specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SREA. For parts and components us

13、ing Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign off must be kept until Job 1. 4.6 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed

14、 by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1 which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis through IMDS and or GMAP reporting. 5. SUMMARY OF REVISIONS