FORD WSS-M15P49-A1-2017 PERFORMANCE FLOOR MAT LOGOS TO BE USED WITH FORD WSS-M99P1111-A .pdf
《FORD WSS-M15P49-A1-2017 PERFORMANCE FLOOR MAT LOGOS TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享,可在线阅读,更多相关《FORD WSS-M15P49-A1-2017 PERFORMANCE FLOOR MAT LOGOS TO BE USED WITH FORD WSS-M99P1111-A .pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 1 2017 07 07 Revised Updated test methods and testing tables A. Collins, NA 2015 06 12 Released L. Sinclair, NA Controlled document at www.MATS Copyright 2017, Ford Global Technologies, LLC Page 1 of 6 PERFORMANCE, FLOOR MAT LOGOS WSS-M1
2、5P49-A1 1. SCOPE The performance defined by this specification is the minimum requirements required for good quality floor mat logos fixed to carpeted floor mat substrates. 2. APPLICATION This specification was released originally for direct embroidered and adhesive melt logos used for floor mat app
3、lications. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification is performance based and does not have approved sources. 3.2 DV/PV TEST PLAN PEC/FEC/PV testing must be conducted in compliance with program milestones unless otherwise specified by Ford Engineering. See Table 2 for DV/PV testing. 3.
4、3 CONDITIONING AND TESTING The logos must be applied to the production representative floor mat composite using a production representative process. See Table 1 and Table 2 for testing requirements & sample size. Final determination of pass/fail criteria for the italicized items will be made by Ford
5、 Engineering. All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity. Testing of the material should occur in the conditioning environment or soon after removal. 3.4 APPEARANCE The color, pat
6、tern, and face construction shall match the approved Corporate Design master sample. 3.5 LOGO SEPARATION FROM FLOOR MAT 3.5.1 Initial Separation Sample Preparation: Take the floor mat with the logo and bend the floor mat 180 under at the edge of the logo. On each side of the logo use a small clamp t
7、o compress the floor mat. Requirement: The logo may not show any visual evidence of peeling, separation from the carpet fibers, loss of adhesion, curling edges, delamination or any other effect which would detract from its proper function or appearance. 3.5.2 Separation after Heat Age Rating 4 min (
8、Prepare per 3.5.1, then FLTM BO 040-01 Procedure B, 80 +/- 2 C, AATCC Evaluation Procedure 1) ENGINEERING MATERIAL SPECIFICATION WSS-M15P49-A1 Copyright 2017 Ford Global Technologies, LLC Page 2 of 6 Requirement: The logo may not show any visual evidence of peeling, separation from the carpet fibers
9、, loss of adhesion, curling edges, delamination, loss of legibility, discoloration, , cracking, excessive shrinkage or any other effect which would detract from its proper function or appearance. 3.5.3 Separation after Humidity Rating 4 min. (Prepare per 3.5.1, then 7 days at 38 +/- 2 C, 95-100% R.H
10、., AATCC Evaluation Procedure 1) Requirement: The logo may not show any visual evidence of peeling, separation from the carpet fibers, loss of adhesion, curling edges, delamination, loss of legibility, discoloration, cracking, excessive shrinkage or any other effect which would detract from its prop
11、er function or appearance. 3.5.4 Separation after Environmental Cycling Rating 4 min (Prepare per 3.5.1, then FLTM BO 040-01 Procedure A, high temperature 80 C, AATCC Evaluation Procedure 1) Requirement: The logo may not show any visual evidence of peeling, separation from the carpet fibers, loss of
12、 adhesion, curling edges, delamination, loss of legibility, discoloration, cracking, excessive shrinkage or any other effect which would detract from its proper function or appearance. 3.5.5 Separation after Cold Cycle Rating 4 min (Prepare per 3.5.1, then 24 h at -30 +/- 2 C AATCC Evaluation Proced
13、ure 1) Requirement: The logo may not show any visual evidence of peeling, separation from the carpet fibers, loss of adhesion, curling edges, delamination, loss of legibility, discoloration, cracking, excessive shrinkage or any other effect which would detract from its proper function or appearance.
14、 3.5.6 Separation after Water Immersion Rating 4 min (Prepare per 3.5.1, then 24 h at 32 +/- 2 C, Completely immersed in a water bath, AATCC Evaluation procedure 1) Requirement: The logo may not show any visual evidence of peeling, separation from the carpet fibers, loss of adhesion, curling edges,
15、delamination, loss of legibility, discoloration, cracking, excessive shrinkage or any other effect which would detract from its proper function or appearance. 3.6 TABER ABRASION 600 cycles (FLTM BN 108-02, CS-10 Wheel, 500 g load) Test shall be conducted with the logo 100% bonded to the substrate to
16、 form a material composite. For high pile carpets, adhesively applied logos can be tested by themselves to prevent the Taber wheels from bouncing on the logos creating localized wear. Logo may not show visual evidence of peeling, loss of legibility, loss of adhesion, curling edges, severe fiber brea
17、kage or any other effect which would detract from its proper function or appearance. ENGINEERING MATERIAL SPECIFICATION WSS-M15P49-A1 Copyright 2017 Ford Global Technologies, LLC Page 3 of 6 3.7 COLOR PROPERTIES 3.7.1 Resistance to Interior Weathering Rating 4 min (FLTM BO 116-01, 225.6 kJ/m2, AATCC
18、 Evaluation Procedure 1) 3.7.2 Resistance to Crocking (FLTM BN 107-01, AATCC Evaluation Procedure 2) Wet Rating 4 min Dry Rating 4 min 3.7.3 Resistance to Cleaning Agents (FLTM BN 107-01, 10 cycles, AATCC Evaluation Procedure 2) Test Procedure: Saturate white cotton cloth with the cleaner listed. Cl
19、eaner: Carpet and Upholstery Cleaner Rating 4 min (Motorcraft ZC-54/Resolve Carpet Cleaner or equivalent) 3.7.4 Soiling and Cleanability (FLTM BN 112-08, AATCC Evaluation Procedure 2) Standard Soil Rating 3 min Grease Rating 3 min Coffee Rating 3 min 3.8 ODOR (FLTM BO 131-03, Variant A) Condition 1
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSSM15P49A12017PERFORMANCEFLOORMATLOGOSTOBEUSEDWITHFORDWSSM99P1111APDF

链接地址:http://www.mydoc123.com/p-751324.html