FORD WSS-M15P39-B-2016 PERFORMANCE HEADREST FOAM IN PLACE TO BE USED WITH FORD WSS-M99P1111-A .pdf
《FORD WSS-M15P39-B-2016 PERFORMANCE HEADREST FOAM IN PLACE TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享,可在线阅读,更多相关《FORD WSS-M15P39-B-2016 PERFORMANCE HEADREST FOAM IN PLACE TO BE USED WITH FORD WSS-M99P1111-A .pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 1 2016 02 29 N Status Replaced by WSS-M15P20-B1/2 A. Wagenhals, NA 2010 05 25 Activated M. Dumitrescu, G. Eaton Copyright 2016, Ford Global Technologies, LLC Page 1 of 3 PERFORMANCE, HEADREST, FOAM IN PLACE WSS-M15P39-B NOT TO BE USED FO
2、R NEW DESIGN 1. SCOPE This specification defines the performance requirements for foam in place molded headrest. 2. APPLICATION This specification was released originally for automotive molded headrest applications. This is not applicable for wrap around applications. Molded foam used in assemblies
3、must also meet WSS-M15P20-B1/B2 requirements. The face materials must meet the requirements of material specifications (eg. M1F, M2F, M1H) and the appropriate Performance Specification. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conf
4、orm to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 SAMPLE SELECTION Testing must be conducted on part at each prototype and production build phase unless specified by Ford Engineering. See Table 1 for DV/PV testing. 3.3 APPEARANCE (FLTM BI 109-01) The color, pat
5、tern, and finish shall match the approved Design Center master sample, or shall be as specified on the engineering drawing. 3.4 CONSTRUCTION These parts consist of face/cover material laminated to foam, which are cut and sewn to the desired shape and injected with foam. Cover - as specified on Engin
6、eering Drawing. Foam - as specified on Engineering Drawing Substrate as specified on Engineering Drawing ENGINEERING MATERIAL SPECIFICATION WSS-M15P39-B Copyright 2016, Ford Global Technologies, LLC Page 2 of 3 3.5 PRODUCT INDENTATION CHARACTERISTICS (FLTM BO 111-02, Method “B“, except as follows:)
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSSM15P39B2016PERFORMANCEHEADRESTFOAMINPLACETOBEUSEDWITHFORDWSSM99P1111APDF

链接地址:http://www.mydoc123.com/p-751303.html