FORD WSS-M15P36-A2-2007 PERFORMANCE INNER DOOR WATERSHIELD WITH PRESSURE SENSITIVE ADHESIVE - TO BE USED WITH FORD WSS-M99P1111-A 《带压敏胶粘剂的内门密封条的性能 与标准FORD WSS-M99P1111-A一起使用 》.pdf
《FORD WSS-M15P36-A2-2007 PERFORMANCE INNER DOOR WATERSHIELD WITH PRESSURE SENSITIVE ADHESIVE - TO BE USED WITH FORD WSS-M99P1111-A 《带压敏胶粘剂的内门密封条的性能 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享,可在线阅读,更多相关《FORD WSS-M15P36-A2-2007 PERFORMANCE INNER DOOR WATERSHIELD WITH PRESSURE SENSITIVE ADHESIVE - TO BE USED WITH FORD WSS-M99P1111-A 《带压敏胶粘剂的内门密封条的性能 与标准FORD WSS-M99P1111-A一起使用 》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions 2007 07 26 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.11, 3.12 & 4 2001 12 14 Revised Revised 3.5, 3.6.3, added 3.8 & renumbered L. Soreide, J. Williams 1995 07 21 Released C10537740 P. Thomas Printed copies are uncontrolled Copyright 200
2、7, Ford Global Technologies, LLC Page 1 of 4 PERFORMANCE, INNER DOOR WATERSHIELD WSS-M15P36-A2 WITH PRESSURE SENSITIVE ADHESIVE 1. SCOPE This specification defines the minimum performance requirements for an inner door and other closure watershield. It is comprised of a base material with pressure s
3、ensitive adhesive (e.g. butyl, hot-melt bead, film) applied on one side, in specified areas. Additional formed sections may be included as required. 2. APPLICATION This specification was released originally for materials used for water shield applications. 3. REQUIREMENTS Material specification requ
4、irements are to be used for initial qualification of materials. 3.0 STANDARD REQURIEMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.4 BASE MATERIAL 3.4.1 Tear Strength, min 7 N (ASTM
5、D 1004) 3.4.2 Dimensional Stability, max (ASTM D 3575) 24 h at 80 +/- 2 C +/- 3% 15 minutes at 100 +/- 2 C +/- 6% 3.4.3 Cold Flexibility No Cracks Test Method: Cut 25 x 150 mm strips in both directions. Condition the strips and a 13 mm diameter mandrel at -40 +/- 2 C for 4 h. Bend the conditioned st
6、rips 180 around the mandrel within 2 - 3 s. 3.4.4 Flammability (ISO 3795/SAE J369) Burn Rate, max 100 mm/minute ENGINEERING MATERIAL SPECIFICATION WSS-M15P36-A2 Printed copies are uncontrolled Copyright 2007, Ford Global Technologies, LLC Page 2 of 4 3.4.5 Fogging (SAE J1756, 3 h at 100 C heating, 2
7、1 C cooling plate, post test conditioning 1 h and 16 h) Fog Number, min 70 Formation of clear film, droplets or crystals is cause for rejection. Adhesive must not adversely affect the result. 3.4.6 Odor, max Rating 2 (FLTM BO 131-01) Adhesive must not adversely affect the result. 3.5 THICKNESS, mm A
8、s specified on the (ISO 1923) Engineering Drawing/ Document 3.6 BASE MATERIAL WITH ADHESIVE All testing must be conducted on production representative topcoat or basecoat/clearcoat test panels using the same paint type as used in the intended assembly plant or plants. All samples must be must be con
9、ditioned for 2 h at 23 +/- 2 C and 50 +/- % relative humidity prior to testing 3.6.1 Peel Adhesion Strength, min (ASTM D 1000, 90 peel angle, Specimen dimension 300 x 25 mm, test speed 300 mm/min, moving plate) Original 4 N/25 mm width After Humidity Aging, Change, max -50% (2 h after bonding expose
10、 for 24 h at 38 +/- 2 C and 95 +/- 5% relative humidity, recondition for 2 h at 23 +/- 2 C and 50 +/- 5% relative humidity) 3.6.2 Shear Adhesion Strength, min (FLTM BU 151-01, Method A, bonding area to be 10 x 25 mm, test speed 25 mm/min) Failure in the base material prior to failure of the adhesive
11、 constitutes a pass. Original 15 N/cm2 After Heat Aging (14 days at 80 +/- 2 C) 3 N/cm2 ENGINEERING MATERIAL SPECIFICATION WSS-M15P36-A2 Printed copies are uncontrolled Copyright 2007, Ford Global Technologies, LLC Page 3 of 4 3.6.3 Cold Adhesion Test Test Method: Bond a 20 mm x 20 mm self adhesive
12、piece of film to a degreased aluminum foil (150 x 60 x 0.2 mm) using maximum finger pressure. Expose specimens for testing as specified below. Then expose each assembly and a 13 mm diameter mandrel for 2 h at -40 +/- 2 C in a cold box. While still in the cold box bend the specimen with the film faci
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSSM15P36A22007PERFORMANCEINNERDOORWATERSHIELDWITHPRESSURESENSITIVEADHESIVETOBEUSEDWITHFORDWSSM99P1111A

链接地址:http://www.mydoc123.com/p-751296.html