FORD WSS-M15P18-B-2014 PERFORMANCE VISIBLE ZIPPER ASSEMBLY COLOR DURABILITY.pdf

《FORD WSS-M15P18-B-2014 PERFORMANCE VISIBLE ZIPPER ASSEMBLY COLOR DURABILITY.pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M15P18-B-2014 PERFORMANCE VISIBLE ZIPPER ASSEMBLY COLOR DURABILITY.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2014 04 29 Released M.Dumitrescu, FNA Controlled document at www.MATS Copyright 2014, Ford Global Technologies, LLC Page 1 of 2 PERFORMANCE, VISIBLE ZIPPER ASSEMBLY COLOR DURABILITY WSS-M15P18-B 1. SCOPE The material defined by this sp

2、ecification is a visible zipper assembly and its color property requirements for interior trim applications. It is not applicable for nonvisible zipper applications. 2. APPLICATION This specification was released originally for material used as a zipper assembly for interior seat, armrest and/or hea

3、drest covers. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements for Production Materials (WSS-M99P1111-A) 3.1.1 In addition to the requirements listed herein, the zipper assembly shall meet all

4、the requirements as specified on the Engineering Drawings and the functional requirements of the application. 3.2 APPEARANCE (FLTM BI 109-01) The color and appearance shall match the approved Design Center master sample, or shall be as specified on the engineering drawing. 3.3 SAMPLE SELECTION See T

5、able 1 for sample size and testing requirements. The test specimens shall be taken from a zipper assembly. 3.4 CONSTRUCTION Zipper type and construction must be specified on the Engineering Drawing and meet ASTM D2060, ASTM D2061, and ASTM D3657. 3.5 COLOR PROPERTIES Submit tested samples to Materia

6、ls Engineering for review and approval. 3.5.1 Resistance to Fade (FLTM BO 116-01, ISO 105-A02/ AATCC Evaluation Procedure 1) 451.2 kJ/m2 Rating 4 min ENGINEERING MATERIAL SPECIFICATION WSS-M15P18-B Copyright 2014 Ford Global Technologies, LLC Page 2 of 2 3.5.2 Resistance to Crocking (FLTM BN 107-01,

7、 ISO 105-A03 / AATCC Evaluation Procedure 2) Dry Rating 4 min Wet (Distilled water) Rating 4 min Zipper teeth should be zipped to run crocking down the middle of the teeth. A piece of tape may be required on the backside of the sipper to hold it together. 3.5.3 Resistance to migration staining and b

8、locking No staining (FLTM BN 103-01) No evidence of injurious exudation, adhesion (tackiness), separation, color transfer, staining when placed against an unsupported white vinyl film. No staining or color transfer to white vinyl film. 4. GENERAL INFORMATION The information given below is provided f

9、or clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 5. SUMMARY OF REVISIONS TABLE 1 Test Sample size Assembly Testing (DV/PV) New Color Only (MCDCC Process) 3.4 .Construction Functional testing by Trim cover Supplier and Tier 1 Supplier 3.5 Color properties 3.5.1 Resistance to Fade, 451.2 kJ/m2 1 per color X 3.5.2 Resistance to Crocking Dry 1 per color X Wet 1 per color X 3.5.3 Resistance to migration staining 1 per color X