FORD WSK-M99J367-A-2012 TOPCOAT ONE PACK STONE PECK PROTECTION SMOOTH TO BE USED WITH FORD WSS-M99P1111-A 《单层防敲击的石制光滑面漆 与福特WSS-M99P1111-A 一起使用》.pdf
《FORD WSK-M99J367-A-2012 TOPCOAT ONE PACK STONE PECK PROTECTION SMOOTH TO BE USED WITH FORD WSS-M99P1111-A 《单层防敲击的石制光滑面漆 与福特WSS-M99P1111-A 一起使用》.pdf》由会员分享,可在线阅读,更多相关《FORD WSK-M99J367-A-2012 TOPCOAT ONE PACK STONE PECK PROTECTION SMOOTH TO BE USED WITH FORD WSS-M99P1111-A 《单层防敲击的石制光滑面漆 与福特WSS-M99P1111-A 一起使用》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 03 2012 03 20 N Status No replacement named N. Benipal, NA 2006 03 23 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.11, 3.13, 4 1991 01 02 Released KW, conc. J. Schult Controlled document at www.MATS Copyright 2012, Ford Global Technolog
2、ies, LLC Page 1 of 4 TOPCOAT, ONE PACK, STONE PECK PROTECTION, SMOOTH WSK-M99J367-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a stone peck resistant topcoat for vehicle bodies. 2. APPLICATION This specification was released originally for material used as d
3、ecorative stone peck resistant topcoat on baked enamel on lower body side areas. It may also be used for catalysed repair in connection with hardener WSK-M99J368-A. 3. REQUIREMENTS Material specification requirements are to be used for initial qualification of materials. 3.0 STANDARD REQUIREMENTS FO
4、R PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.4 COMPOSITION 3.4.1 Resin: Polyester resins and Melamine resins. 3.4.2 Pigments: Pigments to obtain the desired color and resistance properties
5、. 3.4.3 Solvent Emissions see Initial Sample +/- 1% (ASTM D 3960) This requirement is as determined by the United States Environmental Protection Agency Reference Method #24 and is only applicable to materials used in the USA. 3.5 MATERIAL PROPERTIES 3.5.1 Non-volatile see Initial Sample (FLTM BI 10
6、2-01) +/- 3%; min. 55% The non-volatile content shall be determined at viscosity as supplied. 3.5.2 Density see Initial Sample (ASTM D 1475) +/- 0.05 g/mL 3.5.3 Viscosity as supplied 60 +/- 10 s (FLTM BI 111-01, FC #4) ENGINEERING MATERIAL SPECIFICATION WSK-M99J367-A Copyright 2012, Ford Global Tech
7、nologies, LLC Page 2 of 4 3.5.4 Mixing ratio with hardener WSK-M99J368-A (Only if used for catalysed repair). As specified by the supplier, preferred ratio: 3 - 5% 3.5.5 Storage Stability: 90 days During a storage of 90 days between 5 and 32 C temperature the material as supplied shall not settle up
8、 or cake insoluble. After the storage the material must pass all specification requirements. 3.6 PREPARATION OF TEST PANELS 3.6.1 Preparation of Test Panels: (FLTM BI 103-02, Bb) Test Panels shall be painted with current approved two coat silver metallic topcoat materials as well as one coat solid c
9、olor top coat materials (black and white). Ageing: One hour at room temperature 23 +/- 2 C. 3.6.2 Application of WSK-M99J367-A: Dry film thickness: 100 - 120 micrometer Flash off time: 3 minutes Baking: 10 minutes at 130 C (Object temperature) 3.6.3 Repair with Acid Catalyst 3.6.3.1 Repair on baked
10、enamel: Prepare Test Panels as shown in para 3.6.1; Application of WSK-M99J367-A according to 3.5.4 Dry film thickness: 100 - 120 micrometer Flash off time: 3 minutes Baking: 10 minutes at 100 C (Object temperature) 3.6.3.2 Repair on baked stone peck resistant topcoat: Prepare Test Panels as shown i
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSKM99J367A2012TOPCOATONEPACKSTONEPECKPROTECTIONSMOOTHTOBEUSEDWITHFORDWSSM99P1111A 单层 敲击 光滑 福特 WSSM99P1111A

链接地址:http://www.mydoc123.com/p-751076.html