FORD WSK-M14J248-A-1990 SOLVENT NITROCELLULOSE THINNER《硝化纤维溶剂稀释剂》.pdf

《FORD WSK-M14J248-A-1990 SOLVENT NITROCELLULOSE THINNER《硝化纤维溶剂稀释剂》.pdf》由会员分享，可在线阅读，更多相关《FORD WSK-M14J248-A-1990 SOLVENT NITROCELLULOSE THINNER《硝化纤维溶剂稀释剂》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONMaterial Name Specification NumberDate Action Changes1990 02 01 C01031532 released C E Herriott concurred J SchultWP 3948-a Page 1 of 3 SOLVENT, NITROCELLULOSE THINNER WSK-M14J248-A1. SCOPEThe ma terial defined by this specification is a nitrocellulose andpolyester

2、 solvent thinner.2. APPLICATIONThis specification was released originally for material used as thinner todilute airdrying paints to spray viscosity. In general this material isused with WSK-M4J211-A Paint, Clear coat, Air Drying Rep air, Interior alsoproduc tion base coat WSK-M32J124-A to reduce mat

3、erial to applicationviscosity.3. REQUIREMENTS3.1 STATISTICAL PROCESSSupplie rs must conform to the requirements of Ford Quality SystemStand ard Q-101. A mutually acceptable Control Plan as describedtherein is required for material/source approval. Appropriatestatist ical tools must be used to analyz

4、e process/product data sothat variation in the final product is continually reduced.3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSISFord Motor Company in its option, may conduct in frared and/or thermalana lysis of materials/parts supplied to this specification. The IRspectra and thermograms e

5、stablished for initial approval shallconst itute the reference standard and shall be kept on file at thedesignated Material Laboratory. All samples sha ll produce IR spectraand thermograms that correspond to the reference standard when testedunder the same conditions3.3 FLASH POINTThe flash point sh

6、all conform to the safety regu lations applicable tothe plant and/or country where the material shall be used.ENGINEERING MATERIAL SPECIFICATIONWSK-M14J248-AWP 3948-b Page 2 of 3 3.4 COMPOSITIONBlend of ester, alcohol and aromatic hydrocarbons.Xylene, min 60 %Butylacetate 85 % 40 %(15 % n-Butylalcoh

7、ol)3.5 PHYSICAL PROPERTIES3.5.1 StabilityDuring a storage of 2 years at temperature between 5 - 28 C(o r as recommended by the supplier) the material in theclosed original contain er shall remain stable with no changein colour.3.5.2 Density, as delivered 0,8695 +/- 0,0025 g/mL(ASTM D 1475, 20 C)3.5.

8、3 Distillation Range 118 -140 C(ASTM D 1078)3.5.4 Flash Point, min 24 C(ASTM D 56)3.5.5 Refractive Index 1,4547 +/- 0,00173.6 APPEARANCE3.6.1 Colour water-white3.7 SUPPLIERS RESPONSIBILITYAll materials supplied to this specification must be equivalent inal l characteristics to the material upon whic

9、h approval wasoriginally granted.Pri or to making any change in the properties, composition,constr uction, color, processing or labeling of the materialorig inally approved under this specification, whether or not suchchange s affect the materials ability to meet the specificationrequir ements, the

10、Supplier shall notify Purchasing, Toxicology andthe affected Materials Engineering activity of the proposed changesand obtain the written approval of the Materials Engineeringactivity. Test data, t est samples and a new code identification areto be submitted with the request.Substance restrictions i

11、mposed by law, regulations or Ford, apply tothe materials addressed by this document. The restrictions aredefined in Engineering Material Specification WS S-M99P9999-A1, unlessa different suffix (e.g., A2 or A3) is specified on the engineeringdocument for the application.ENGINEERING MATERIAL SPECIFI

12、CATIONWSK-M14J248-AWP 3948-b Page 3 of 3 4. APPROVAL OF MATERIALSMat erials defined by this specification must have prior approval by theresponsible Materials Engineeri ng activity. Suppliers desiring approval ofthe ir materials shall first obtain an expression of interest from theaffec ted Purchasi

13、ng, Design and Materials Engineering activity. Uponrequest, the Supplier shall submit to the affected Materials Engineeringactivity its own laboratory rep ort to the specification (test results, notnominal values), the material designation and code number, and testspecim ens for Ford evaluation. Upo

14、n approval, the material will be addedto the Engineering Material Approved Source List.5. GENERAL INFORMATIONThe information below is provided for clarification and assistance inmeeting the requirements of the specification.5.1 MANUFACTURING ENGINEERING REFERENCESApplicable Process StandardVehicles which are produced in NAAOC-200 (F) General PaintingC-600 (F) ElectrocoatPL53-33 (F) PhosphateVehicles which are produced in EAOC-800 PAINTING -PROCESS