FORD WSB-M2D467-A-2009 THERMOPLASTIC POLYOLEFIN (TPO) MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用热塑性聚烯烃(TPO)成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf
《FORD WSB-M2D467-A-2009 THERMOPLASTIC POLYOLEFIN (TPO) MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用热塑性聚烯烃(TPO)成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享,可在线阅读,更多相关《FORD WSB-M2D467-A-2009 THERMOPLASTIC POLYOLEFIN (TPO) MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用热塑性聚烯烃(TPO)成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2009 09 21 N-STATUS No Replacement Named, No known use C. Mracna, NA 2004 10 13 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.10, 3.11 Corrected numbering 3.6.7, 3.6.8, 3.6.9 1991 05 16 Released NB00I10043054083 K. Minnich L. Graham Printed c
2、opies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 1 of 3 THERMOPLASTIC POLYOLEFIN (TPO) MOLDING WSB-M2D467-A COMPOUND, INTERIOR NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a flexible thermoplastic polyolefin (TPO) injection and/or extr
3、usion molding compound with UV stability for self-colored interior applications. 2. APPLICATION This specification was released originally for material used for interior seat belt sling boot applications. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part
4、producers must conform to the Companys Standard requirements For Production Materials (WSS-M99P1111-A). 3.4 DYNAMIC MECHANICAL ANALYSIS (ASTM D 4065) Ford Motor Company, at its option, may establish a shear modulus/damping vs. temperature curves plotted for -50 to +170 C temperature range for materi
5、al/parts supplied to this specification. The shear modulus and damping curves established for initial approval shall constitute the reference standard and shall be kept on file at the designated material laboratory. All samples shall produce shear modulus and damping curves that correspond to the re
6、ference standard when tested under the same conditions. 3.5 MOLDING COMPOUND 3.5.1 Filler Content 16 - 20% (ISO 3451/1, Method A) 3.6 MOLDED TEST SPECIMEN 3.6.1 Preparation of Test Specimens Unless otherwise specified, all tests shall be conducted on specimens die cut from injection molded plaques 1
7、50 x 100 x 2.0 +/- 0.2 mm. The plaques shall be molded according to ISO 294 and film gated along the upper 100 mm edge. No annealing allowed, unless otherwise specified. 3.6.2 Density 0.98 - 1.02 g/cm3(ISO 1183, Method A/ASTM D 792, Method A1) 3.6.3 Hardness, International 82 - 88 (ISO 48/ASTM D 141
8、5) ENGINEERING MATERIAL SPECIFICATIONWSB-M2D467-APrinted copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 2 of 3 3.6.4 Hardness, Durometer A 82 - 88 (ISO 868/ASTM D 2240, 6 mm thick plied-up specimen, instantaneous reading) 3.6.5 Tensile Strength at Break, min 6.6 MPa (ISO
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSBM2D467A2009THERMOPLASTICPOLYOLEFINTPOMOLDINGCOMPOUNDINTERIORTOBEUSEDWITHFORDWSSM99P1111A 汽车 内部

链接地址:http://www.mydoc123.com/p-748984.html