FORD WSB-M16J16-A-2012 PAINT WATERBORNE 2 COMPONENT COMPLIANCE VOC PLASTICS EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSB-M16J16-A-2012 PAINT WATERBORNE 2 COMPONENT COMPLIANCE VOC PLASTICS EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSB-M16J16-A-2012 PAINT WATERBORNE 2 COMPONENT COMPLIANCE VOC PLASTICS EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONMaterial Name Specification NumberDate Action Changes1996 05 08 Activated H. Kon J. FauntWP 3948-a Page 1 of 9 PAINT, WATERBORNE, 2 COMPONENT COMPLIANCE VOC, WSB-M16J16-APLASTICS, EXTERIOR1. SCOPEThe ma terial defined by this specification is a waterborne, two comp

2、onentpai nt system for use on thermoplastic exterior parts subject to polarsolvents, abrasion and limited sunlight.2. APPLICATIONThi s specification was released orginally for cowl leaf screens. Thecoatin g described must have superior resistance to windshield washersol vent. The paint and crosslink

3、ing material must be blended perinstructions to achieve satisfactory properties.3. REQUIREMENTS3.1 QUALITY SYSTEM REQUIREMENTSMaterial suppliers and part producers must conform to Quality SystemRequirements, QS-9000. Material specification r equirements are to beused fo r initial qualification of ma

4、terials. A Control Plan forong oing production verification is required. This plan must bereviewed and approved b y the relevant Ford Materials activity and/orFor d Supplier Technical Assistance (STA) prior to production partssubmission. Appropriate statistical tools must be used to analyzepr ocess/

5、product data and assure consistent processing of thematerials.Part producers using this material in their products, must use Fordapproved materials and must conform to a process control plan whichhas been approved by STA and/or the relevant Materials Activity.3.2 INFRARED SPECTROPHOTOMETRY AND/OR TH

6、ERMAL ANALYSISFord Motor Company, at its option, may conduct infrared and/ortherma l analysis of material/parts supplied to this specification.The IR spectra and thermograms established for i nitial approval shallconst itute the reference standard and shall be kept on file at thedesignated material

7、laboratory. All samples sha ll produce IR spectraand thermograms that correspond to the reference standard when testedunder the same conditions.ENGINEERING MATERIAL SPECIFICATIONWSB-M16J16-AWP 3948-b Page 2 of 9 3.3 CONDITIONING AND TEST CONDITIONSAll test values indicated herein are based on ma ter

8、ial conditioned ina control led atmosphere of 23 +/- 2 C and 50 +/- 5 % relativehumidity for not less than 24 h prior to testing and tested under thesame conditions unless otherwise specified.3.4 COMPOSITION3.4.1 Vehicle: Waterborne acrylic emulsion with minor amounts ofadditives and surfactan ts to

9、 provide good pigment dispersionand substrate adhesion.3.4.2 Ultraviolet Light Absorber(s)/Stabilizer(s): The coatingshall contain these materials in amounts sufficient toprovide long-term durability for the coating.3.4.3 Pig ments: The pigment blend shall provide a satisfactorycolor m atch to the F

10、ord master panel on file and meet therequirements of this specification for durability.3.4.4 Crosslinker: Polyfunctional Aziridine Crosslinker3.4.5 Volatile: The proportion of solvents in the paint shall beformulated that the film will level out satisfactorilywit hout sagging, popping or roughness a

11、fter baking whenapplied within the specified film thickness range.3.4.6 Specific Composition: The supplier shall furnish such dataupon request.3.5 PHYSICAL PROPERTIES3.5.1 Volatile Organic Compou nds: Allowable weight at applicationviscosity.(U.S. EPA Method 24 - minus water)All colors individually

12、shall not exceed 0.60 kg/L.3.5.2 Viscosity: Application(FLTM BI 111-01)Shall be established by the supplier on the initial approvedproduction batch. Tolerance shall be +/- 5 s.3.5.3 pH(ASTM E 70 at application viscosity)Shall be established by the supplier on the initial approvedproduction batch. To

13、lerance shall be +/- 0.2 unit.ENGINEERING MATERIAL SPECIFICATIONWSB-M16J16-AWP 3948-b Page 3 of 9 3.5.4 Stability (each component, before mixing)(6 months at 23 +/- 2 C)Neither the paint nor catalyst shall jell upon s tanding. Thepaint must be free from settling which is not dispersed bynorm al agit

14、ation. The components must be easily blendedtogether during this period.Stability (Blended and adjusted to application viscosity)24 hours at plant environment temperature and humidity.The coating must remain in the viscosity range specified inpa ra 3.5.2 and meet all requirements of this specificati

15、onfor the 24 hour period.3.6 PREPARATION OF TEST PANELS3.6.1 SubstrateAll test specimens shall be injection molded plaques havinga nominal thickness of 3 +/- 0.5 mm.3.6.2 Substrate PreparationAll spec imens shall be free of mold release agents, fingerprints, oils, dirt and any other detrimental surf

16、acecontamination.3.6.3 Primer, (if required)Ap ply currently approved adhesion promoter or an approvedprimer to the recommended film thickness. Cure permanufacturers recommendation.3.6.4 Color Topcoat 20 - 30 micrometreApply sufficient topcoat to at least hiding film thickness.Cure panels per manufa

17、cturers recommendation.3.7 APPEARANCE3.7.1 GeneralThe coating shall exhibit no craters, pinholes, solventpopping, seediness, abnormal roughness, or excessive flow.3.7.2 Color(FLTM BI 109-01)Shall match the Ford master panel after being prepared asdescribed in para 3.6.ENGINEERING MATERIAL SPECIFICAT

18、IONWSB-M16J16-AWP 3948-b Page 4 of 9 3.7.3 Gloss(FLTM BI 110-01, 60 degree Glossmeter)The gloss shall be specified by means of a letter suffix tothe color code assigned as follows:B 80 +/- 4 F 35 +/- 3C 70 +/- 4 G 20 +/- 3D 62 +/- 3 H 10 +/- 2E 50 +/- 3 J 6 max3.7.4 Dry Hiding(FLTM BI 158-01)Complet

19、e visual hiding is over a black and gray straight linehiding chart.Black and Metallic Colors 13 - 22 micrometreOther colors 15 - 30 micrometre*When the maximum film thickness value needs to be exceededto obtain visual and/or UV hiding (para 3.7.5), the requiredvalue will be included in the Control P

20、lan submitted to theinvolved Ford activities.3.7.5 Ultraviolet Light TransmissionMeasure the light tramsmittance of the coating a t the minimumand maximum dry hiding film thicknesses listed in para 3.7.4at 400 nm using a Lambda 6 Integrating Sphere spectrometer.If the light transmission exceeds 1.0

21、%, then determine thefil m thickness required to lower the transmission to lessthan 1.0 %. Record thi s value on product data sheets and onthe Control Plan submitted to the involved Ford activites.3.8 FILM PROPERTIESAll film properties are based on the proper preparation per para 3.6and after 72 h a

22、t 23 +/- 2 C post cure.3.8.1 Film Thickness Requirements 18 - 30 micrometre(ASTM D 4138)3.8.2 Adhesion Fig 1 or better(FLTM BI 106-01, Method B)3.8.3 Polish Resistance(FLTM BI 10-02, 60 deg glossmeter)The painted plaque shall exhibit no greater change in glossthan 5 units.ENGINEERING MATERIAL SPECIF

23、ICATIONWSB-M16J16-AWP 3948-b Page 5 of 9 3.9 RESISTANCE REQUIREMENTS3.9.1 Water Immersion 240 h(FLTM BI 104-01)Te st Method: Immerse the test plaque or part for 240 h indistil led or deionized water maintained at 32 +/- 2 C asdescri bed in FLTM BI 104-01. Remove plaque/part from thewater and immedia

24、tely scribe an “X“ through the finish to thesubstrate. Dry the scribed area with either a paper towel,cloth or air (oil free) and immediately apply wi th firm thumbpressure, a minimum of 1300 mm2 of 3M #898 tape. Remove thetape by pulling one end at a 90 deg angle at moderate speed.The following con

25、ditions shall be basis for rejection:. Removal of paint beyond 1.6 mm from any scribe line. Any evidence of blistering or dulling of the paint.3.9.2 Thermal Shock Resistance No blistering or loss of(FLTM BI 107-05, except adhesion 2 mm from scri be4 h immersion at 32 +/- 1 C)3.9.3 Mar and Scratch Re

26、sistance(FLTM BN 108-04, scuff head “A“with a 0.9 kg load)The coating shall not exhibit wear through to su bstrate after1,500 cycles.3.9.4 Abrasion Resistance(FLTM BN 108-02, CS-10 wheels,500 g load)The coating shall not exhibit wear through to su bstrate after3,000 cycles.3.9.5 Resistance to Water

27、and Soap Spotting Rating 4-5 AATCC(FLTM BI 113-01)3.9.6 Resistance to Acid Spotting(FLTM BI 113-05)10 minutes - No discoloration20 minutes - 4-5 AATCC30 minutes - 4 AATCC3.9.7 Resistance to Waxing and Dewaxing Compounds(FLTM BO 155-01)The part shall not craz e, crack or change in gloss more than+/-

28、5 units from the value obtained in para 3.7.3.ENGINEERING MATERIAL SPECIFICATIONWSB-M16J16-AWP 3948-b Page 6 of 9 3.9.8 Windshield Washer Fluid ResistanceParts shall be tested as described in Methods 1, 2 surrogate parts acceptable.ENGINEERING MATERIAL SPECIFICATIONWSB-M16J16-AWP 3948-b Page 8 of 9

29、3.9.11.2 Xenon Arc Weatherometer Rating (see below)(SAE J1960, 2500 kJ/m2)BORDERLINE UNACCEPTABLEDL 2.9 - 3.4 3.4DC 1.5 - 2.0 2.0DH 1.0 - 1.5 1.5DE 2.9 - 3.4 3.4Valu es represent approximately Rating 3 on AATCCGray Scale.3.10 ADDITIONAL REQUIREMENTSSpecific requirements for material and/or manuf act

30、ured parts shall bespecified on the Engineering drawing, Engineeri ng parts specificationand/or performance specification. All critical areas with respect tothese properties shall be clearly designated on the engineeringdrawing.3.11 SUPPLIERS RESPONSIBILITYAll materials supplied to this specificatio

31、n must be equivalent inal l characteristics to the material upon which approval wasoriginally granted.Pri or to making any change in the properties, composition,constr uction, color, processing or labeling of the materialorig inally approved under this specification, whether or not suchchange s affe

32、ct the materials ability to meet the specificationrequir ements, the Supplier shall notify Purchasing, Toxicology andthe affected Materials Engineering activity of the proposed changesand obtain the written approval of the Materials Engineeringactivity. Test data, test samples and a new code identif

33、ication areto be submitted with the request.Substance restrictions imposed by law, regulations or Ford, apply tothe materials addressed by this document. The restrictions aredefined in Engineering Materials Specification WSS-M99P9999-A1.ENGINEERING MATERIAL SPECIFICATIONWSB-M16J16-AWP 3948-b Page 9

34、of 9 4. APPROVAL OF MATERIALSMate rials defined by this specification must have prior approval by theresponsible Materials Engineeri ng activity. Suppliers desiring approval ofthei r materials shall first obtain an expression of interest from theaffect ed Purchasing, Design and Materials Engineering

35、 activity. Uponrequest, the Supplier shall submit to the affected Materials Engineeringactivity a completed copy of their laboratory test reports, signed by aqualified and authorized representative of the test faci lity, demonstratingfull compliance with all the requirements of this specification (t

36、estresults, not nominal values), the material designation a nd code number, andtest specimens for Ford evaluation. Fords engineering approval of amateri al will be based on its performance to this specification and on anassessment of suitability for intended processes and/or applications. Uponapprov al, the material will be added to the Engineering Material ApprovedSource List.