FORD WSB-M11P58-A-1995 ADHESION REQUIREMENTS ADHESIVE FOR BONDING RIGID PLASTIC TO CERAMIC PAINT COATED GLASS《用于将硬质塑料粘合到陶瓷涂料涂层玻璃上的胶粘剂的粘附力要求》.pdf

《FORD WSB-M11P58-A-1995 ADHESION REQUIREMENTS ADHESIVE FOR BONDING RIGID PLASTIC TO CERAMIC PAINT COATED GLASS《用于将硬质塑料粘合到陶瓷涂料涂层玻璃上的胶粘剂的粘附力要求》.pdf》由会员分享，可在线阅读，更多相关《FORD WSB-M11P58-A-1995 ADHESION REQUIREMENTS ADHESIVE FOR BONDING RIGID PLASTIC TO CERAMIC PAINT COATED GLASS《用于将硬质塑料粘合到陶瓷涂料涂层玻璃上的胶粘剂的粘附力要求》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、ENGINEERING MATERIAL SPECIFICATIONMaterial Name Specification NumberDate Action Changes1995 05 15 Revised H. Kon1994 07 20 NB00I10127150813 H. KonWP 3948-a Page 1 of 4 ADHESION REQUIREMENTS, ADHESIVE FOR BONDING WSB-M11P58-ARIGID PLASTIC TO CERAMIC PAINT-COATED GLASS1. SCOPEThis specification define

2、s the adhesion requiremen ts for an adhesive or anadhesive system suitable for structurally bonding rigid plastic (FlexuralModulus of greater than 2500 MPa) to ceramic paint coated glass.2. APPLICATIONThi s specification was released originally for materials used to bondrigid plastic window frames t

3、o ceramic paint coate d glass for the 1996 PN-96 Backlight window module. Material systems meeting this performance specific ation are available fromthe responsible Materials Engineering Activity. Any modification orsubstitution of components of a material system or any new material systemwill r equ

4、ire complete specification compliance certification by theresponsible Materials Engineering Activity.Com pliance with this performance specification does not guarantee theadhesive system will function for all potential ap plications on a vehicle.The sp ecific assembly must be evaluated for functiona

5、l performancereq uirements and its durability verified by the responsible MaterialsEngineering Activity prior to its release. 3. REQUIREMENTS3.1 QUALITY SYSTEM REQUIREMENTSMaterial suppliers and part producers must conform to Quality SystemRequirements, QS-9000. Material specification requirements a

6、re tobe used for initial quali fication of materials. A Control Plan forong oing production verification is required. This plan must bereviewed and approved by the relevant Ford Materia ls activity and/orFord Supplier Technical Assistance (STA) prior to production partssubmission. Appropriate statis

7、tical tools must be used to analyzepro cess/product data and assure consistent processing of thematerials.Part producers using this material in their products, must use Fordapproved materials and mu st conform to a process control plan whichhas been approved by STA and/or the relevant Materials Acti

8、vity.3.2 CONDITIONING AND TEST CONDITIONSAll test values indicated herein are based on material conditionedin a con trolled atmosphere of 23 +/- 2 C and 50 +/- 5 % relativehumidity for not less than 24 h prior to testing and tested underthe same conditions unless otherwise specified.ENGINEERING MATE

9、RIAL SPECIFICATIONWSB-M11P58-AWP 3948-b Page 2 of 4 3.3 SHEAR ADHESION STRENGTH, minimum Cohesive failureor substrate breakage(ASTM D 3163, 12.7 mm/min crossheadspeed, 0.76 mm bondline thickness, 13 mm overlap, substrates per para 5.1,cure schedules per para 5.2, 10 samples per test condition, see F

10、igure 1 for sample illustration)Temperature Conditioning:(Condition for 30 minutes at specifiedtemperature prior to test)3.3.1 Test at 23 +/- 2 C 3.5 MPa3.3.2 Test at 90 +/- 2 C 1.5 MPa3.3.3 Test at - 40 +/- 2 C 3.5 MPaEnvironmental Aging:(Condition for 24 h (min) at 23 +/- 2 Cafter exposure, then t

11、est at 23 +/- 2 C)3.3.4 500 h heat age at 90 +/- 2 C 3.5 MPa3.3.5 500 h humidity at 40 +/- 2 C 3.5 MPa3.3.6 500 h water immersion at 30 +/- 2 C 3.5 MPa(FLTM BI 104-01, Procedure CNo Tape-pull required)3.3.7 500 h salt spray 3.5 MPa(ASTM B117)3.3.8 1000 h Xenon Arc, Accelerated aging 3.5 MPa (SAE J19

12、60)3.3.9 10 thermal cycles: 3.5 MPa4 h at 90 +/- 2 C, 4 h humidity at 40 +/- 2 C and 95 - 100 % relative humidity, 16 h at - 30 +/- 2 C3.3.10 Florida Exposure 3.5 MPa(SAE J1976, Procedure AReported at 6, 12, 18, 24 months)3.4 FUNCTIONAL APPROVALMaterials being evaluated for approval to this specific

13、ation shallbe subjected to a production trial. Functional trial results mustbe approved by the affected assembly operation and DesignEngineering. Results shall be made available to MaterialsEngineering prior to material approval and release.ENGINEERING MATERIAL SPECIFICATIONWSB-M11P58-AWP 3948-b Pag

14、e 3 of 4 3.5 SUPPLIERS RESPONSIBILITYAll materials supplied to this specification must be equivalent inall cha racteristics to the material upon which approval wasoriginally granted.Prior to making any change in the properties, composition,construction, color, processing or labeling of the materialo

15、riginally approved under this specification, whether or not suchcha nges affect the materials ability to meet the specificationrequirements, the Supplier shall notify Purchasing, Toxicology andthe affected Materials En gineering activity of the proposed changesand ob tain the written approval of the

16、 Materials Engineeringactivity. Test data, test samples and a new code identification areto be submitted with the request.Substance restrictions imposed by law, regulations or Ford, apply tothe materials addressed by this document. The restrictions aredefined in Engineering Material Specification WS

17、S-M99P9999-A1,unless a different suffix (e.g., A2 or A3) is specified on theengineering document for the application.4. APPROVAL OF MATERIALSMater ials defined by this specification must have prior approval by theresponsible Materials Engineering activity. Suppliers desiring approvalof their materia

18、ls shall first obtain an expression of interest from theaff ected Purchasing, Design and Materials Engineering activity. Uponrequest, the Supplier shall submit to the affected Materials Engineeringact ivity a completed copy of their laboratory test reports, signed by aqu alified and authorized repre

19、sentative of the test facility,demonstrating full compliance with all the requirements of thisspecification (test results, not nominal values), The material designationand code number, and test specimens for Ford evaluation. Fordsengine ering approval of a material will be based on its performance t

20、othis spe cification and on an assessment of suitability for intendedprocesses and/or applications. Upon approval, the material will be addedto the Engineering Material Approved Source List.5. GENERAL INFORMATIONThe information given below is provided for clarification and assistancein meeting the r

21、equirements of this specification.5.1 SUBSTRATESSub strates meeting this specification are listed as aco mponent of the material/adhesive system and are available fromthe responsible Materials Engineering Activity.5.2 CURE PROCEDURESAdhesive cure schedule shall conform to requirements called out inthe corresponding Engineering Material Specification. ENGINEERING MATERIAL SPECIFICATIONWSB-M11P58-AWP 3948-b Page 4 of 4