FORD WRS-M3H168-A1-2016 CARPET RECYCLED POLYESTER NON WOVEN FLAT NEEDLED LATEX BACKED 700 g m2 (20 6 oz) 100% PCR CONTENT TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WRS-M3H168-A1-2016 CARPET RECYCLED POLYESTER NON WOVEN FLAT NEEDLED LATEX BACKED 700 g m2 (20 6 oz) 100% PCR CONTENT TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WRS-M3H168-A1-2016 CARPET RECYCLED POLYESTER NON WOVEN FLAT NEEDLED LATEX BACKED 700 g m2 (20 6 oz) 100% PCR CONTENT TO BE USED WITH FORD WSS-M99P1111-A .pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 00 2016 11 17 Released M. Souza, SA Controlled document at www.MATS Copyright 2016, Ford Global Technologies, Inc. Page 1 of 4 CARPET, RECYCLED POLYESTER, NON WOVEN, WRS-M3H168-A1 FLAT NEEDLED, LATEX BACKED, 700 g/m2 (20.6 oz) 100% PCR CO

2、NTENT 1. SCOPE The material defined by this specification is flat needled, nonwoven carpet of good quality and uniform composition. The carpet face is made with 100% post consumer fiber. 2. APPLICATION This specification was released originally for the Ecosport 2018 MY trunk carpet. 3. REQUIREMENTS

3、3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford at or avai

4、lable externally through a Ford Materials Engineer. 3.2 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity. Testing of the material should occur in the co

5、nditioning environment or soon after removal. 3.3 PERFORMANCE CRITERIA 3.3.1 In addition to the requirements listed herein, the end-item floor carpet shall be tested to WSS-M15P32-D and any additional SDS requirements. The details for each of the suppliers specific construction shall be documented i

6、n the supplement attached and uploaded into the scanned data package. 3.3.2 Vehicle Interior Environment Quality Materials/Component Performance Requirements Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-D1/ latest. Data must be included at the appropria

7、te program milestone. 3.3.3 Recycled Content This specification must contain 100% recycled content as defined by WRS- M99P42-A2 (Textile Materials, Identification of Recycled Content). 3.4 SAMPLE SELECTION ENGINEERING MATERIAL SPECIFICATION WRS-M3H168-A1 Copyright 2016, Ford Global Technologies, Inc

8、. Page 2 of 4 All evaluations shall be conducted on test specimens taken from finished roll goods prior to any subsequent operations, such as reheating or molding. 3.5 APPEARANCE The color, pattern, and gloss shall match the approved Corporate Design master sample. 3.6 COMPOSITION 3.6.1 Face Fiber P

9、olyester (100% PCR) (ASTM D276) 3.6.2 Primary Backing Latex (ASTM D276) 3.7 METHOD OF DYEING Solution dyed 3.8 CONSTRUCTION 3.8.1 Face Fiber 14 Denier (ASTM D 1244) 3.9 THICKNESS* 3.0 +/- 1.0 mm *Face thickness prior to molding. 3.10 WEIGHT 3.10.1 Face Fiber 630 - 770 g/m2 (ASTM D5848) (18.6 - 22.7)

10、 oz/yd 3.10.2 Primary Backing 225 - 275 g/m2 (ASTM D5848) (6.6 8.1) oz/yd 4. GENERAL INFORMATION This information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 DRA

11、WING CALL OUT The following shall be called out on the Engineering drawing to correctly designate the approved material. WRS-M3H168-A1 Supplier Name and Product Code (As it appears on the Approved Source Listing) WSS-M15P32-D 4.2 APPROVAL OF MATERIALS Suppliers desiring approval of their materials s

12、hall first obtain an expression of interest from Purchasing, Design or Product Development, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance

13、with all the requirements of ENGINEERING MATERIAL SPECIFICATION WRS-M3H168-A1 Copyright 2016, Ford Global Technologies, Inc. Page 3 of 4 the Material Specification. Tested material samples must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will r

14、eview the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. 4.3 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalent in all characteristics to the material upon which approval was originally granted. Prior t

15、o making any changes to the material originally approved, whether or not such changes affect the materials ability to meet the specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed chan

16、ges (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SREA. For parts and components using Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Production Part Approval

17、Process (PPAP) sign off must be kept until Job 1. 4.4 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M

18、99P9999-A1 which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis through IMDS and or GMAP reporting. 5. SUMMARY OF REVISIONS ENGINEERING MATERIAL SPECIFICATION WRS-M3H168-A1 Copyright 2016, Ford Global Technologies, Inc. Page 4 of 4 Non Woven

19、Carpet Construction Supplement Supplier _Supplier Contact Name_ Number _ Product/ Style Name _ Material Specification _ Performance Specification _ Supplier Product Code _ Manufacturing Location _ Supplier Lab Number _ Supplier Lab Date _ Composition Type Supplier Face Fiber ASTM D276 _ _ Minimum Re

20、cycled Content _ % PIR _ % PCR Pre-Coat ASTM D276 _ _ Mass Backing ASTM D276 _ _ Back Coating ASTM D276 _ _ Construction Solution or piece dyed (circle one) Denier (s) _ Face Fiber Thickness ISO 1765 _+/- _ mm Pre Coating Thickness ISO 1765 _+/- _ mm Mass Backing Thickness ISO 1765 _+/- _ mm Back Coating Thickness ISO 1765 _+/- _ mm Mass per Unit Area Weight Face Fiber ASTM D5848 _+/- _ g/m2 Pre Coating ASTM D5848 _+/- _ g/m2 Mass Backing ASTM D5848 _+/- _ g/m2 Back Coating ASTM D5848 _+/- _ g/m2 Materials Engineering Signature _Date _ Comments _ Rolled Goods _ Molded Product _