FORD WRS-M1H1312-A23-2017 FABRIC ARMSTRONG PATTERN FLAT WOVEN RECYCLED PIR PCR CONTENT WITH SOIL REPELLANT AND BACKCOATING TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WRS-M1H1312-A23-2017 FABRIC ARMSTRONG PATTERN FLAT WOVEN RECYCLED PIR PCR CONTENT WITH SOIL REPELLANT AND BACKCOATING TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WRS-M1H1312-A23-2017 FABRIC ARMSTRONG PATTERN FLAT WOVEN RECYCLED PIR PCR CONTENT WITH SOIL REPELLANT AND BACKCOATING TO BE USED WITH FORD WSS-M99P1111-A .pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2017 12 13 Released L. Pollard, NA Controlled document at www.MATS Copyright 2017, Ford Global Technologies, LLC Page 1 of 3 FABRIC, ARMSTRONG PATTERN, FLAT WOVEN, WRS-M1H1312-A23 RECYCLED, PIR/PCR CONTENT WITH SOIL REPELLANT AND BACKC

2、OATING 1. SCOPE The material defined by this specification is a flat woven polyester face fabric containing a minimum of 25% PIR/PCR (Post industrial/post consumer) recycled yarn. 2. APPLICATION This specification was released originally for material used as an interior trim fabric for 2020 MY Explo

3、rer seat insert. The fabric was originally approved as bi-laminated with foam. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing

4、, CAD file, or other documents. The list of approved sources is located within Ford at or available externally through a Ford Materials Engineer. 3.2 APPEARANCE The color, pattern, and finish shall match the approved Corporate Design master sample. 3.3 FABRIC PERFORMANCE In addition to the requirem

5、ents listed herein, the fabric shall meet all requirements of WSS-M8P18-B1/B2/B3/B4/latest as applicable. 3.4 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative hu

6、midity. Testing of the material should occur in the conditioning environment or soon after removal. 3.5 FABRIC CONSTRUCTION 3.5.1 Fabric Count, -/+ 5% tolerance (ASTM D3775) Warp 620 / 10 cm Fill 240 / 10 cm ENGINEERING MATERIAL SPECIFICATION WRS-M1H1312-A23 Copyright 2017, Ford Global Technologies,

7、 LLC Page 2 of 3 3.5.2 Fabric Weight, -/+ 5% tolerance (FLTM BN 106-01) Face Fabric 275 g/m2 Back Coating 35 g/m2 Total Weight 310 g/m2 3.5.3 Fabric Stretch and Set (SAE J855) Stretch Set Warp 6% min 1% max Fill 6% min 1% max 3.6 COMPOSITION (ASTM D629) Fabric 100% polyester Backcoating 100% polyure

8、thane 3.7 YARN CONSTRUCTION (ASTM D1244) Warp 167 Dtex f48, (false twist, polyester, 250 TPM)Fill 501 Dtex f144, (false twist, recycled polyester) 3.8 RECYCLED CONTENT Recycled yarn must contain a minimum of 25% recycled content PIR/PCR (Postindustrial/post consumer) as defined by WRS-M99P42-A2. The

9、 remaining portion of the material can come from virgin sources. Refer to the Approved Source List (ASL), for specific regional recycled levels for this material. 3.9 METHOD OF DYEING Solution dyed 3.10 FINISHED OPERATIONS Washing, Drying, SR & Finishing, Thermoheatting, Backcoating Any changes to t

10、he above process must be approved by Materials Engineering. 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 Purchase departmen

11、ts will ensure that the material defined in this specification and shipped to any one assembly plant will be produced by one supplier only. In the event of a Global Program or ENGINEERING MATERIAL SPECIFICATION WRS-M1H1312-A23 Copyright 2017, Ford Global Technologies, LLC Page 3 of 3 regional duplic

12、ation, each regional location of the supplier for this specification must provide a construction package and be approved to meet this specification. 4.2 If yarn is locally sourced it must meet the above fabric construction, composition and yarn construction. The fabric must also meet the requirement

13、s of WSS-M8P18-B1/B2/B3/B4/latest. 4.3 Global strategy for this fabric is to use tri-laminate/foam & scrim construction in all regions. 4.4 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Product Development

14、, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material Specification. Tested material samples must be a

15、vailable for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. 4.5 SUPPLIERS ONGOING RESPONSIBILITY All materials must be

16、 equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved, whether or not such changes affect the materials ability to meet the specification requirements, the supplier shall notify the affected Supp

17、lier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SREA. For parts and components using Ford Engineering Material Specifications, all samples tested to the s

18、pecifications for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign off must be kept until Job 1. 4.6 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1/latest which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis. 5. SUMMARY OF REVISIONS