FORD WA 900-2011 Dimensional Requirements of Hexagon Bolts Flanged Hexagon Bolts and Hexagon Bolt&Washer Assemblies《六角螺栓 带凸缘六角螺栓和六角螺栓与垫圈组件的尺寸要求》.pdf

《FORD WA 900-2011 Dimensional Requirements of Hexagon Bolts Flanged Hexagon Bolts and Hexagon Bolt&Washer Assemblies《六角螺栓 带凸缘六角螺栓和六角螺栓与垫圈组件的尺寸要求》.pdf》由会员分享，可在线阅读，更多相关《FORD WA 900-2011 Dimensional Requirements of Hexagon Bolts Flanged Hexagon Bolts and Hexagon Bolt&Washer Assemblies《六角螺栓 带凸缘六角螺栓和六角螺栓与垫圈组件的尺寸要求》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 WORLDWIDE FASTENER STANDARDWA 900 Date: 2011 12 23 Copyright 2011, Ford Global Technologies, LLC Page 1 of 11 Printed copies are uncontrolled Dimensional Requirements of Hexagon Bolts, Flanged Hexagon Bolts and Hexagon Bolt&Washer Assemblies 1. SCOPE This standard gives dimensional requirements for

2、 hexagon bolts, flanged hexagon bolts and bolt & washer assemblies with ISO metric thread diameters M4 to M24 inclusive for hexagon bolts and M5 to M16 inclusive for flanged hexagon bolts. 2. REFERENCES ISO 261 General purpose metric screw threads - General plan. ISO 965 General purpose metric screw

3、 threads - Tolerances. ISO 1502 General purpose metric screw threads - Gauging. ISO 4753 Fasteners - Ends of parts with external Metric ISO thread. ISO 6157-3 Fasteners Surface discontinuities. ISO 15071 Hexagon bolts with flange Small series Product grade A. WA 950 Material Requirements & Mechanica

4、l Properties of Bolts, Studs, and Bolt & Washer Assemblies. WA 990 Surface Discontinuities of Bolts and Screws. WF 900 Dimensional, Material, Heat Treatment, Hardness and Performance Requirements for Flat, Toothed, Conical, Bowed and Wavy Washers for general use and for use in Screw or Nut and Washe

5、r Assemblies. 3. GENERAL REQUIREMENTS 3.1 DIMENSIONS AND TOLERANCES The basic dimensions are shown in the individual product standards or Utility Part drawings. Unspecified dimensions and tolerances shall be in accordance with: ISO 15071 for hexagon flange headed bolts. ISO 15071 for the shank porti

6、on of hexagon headed bolts. ISO 4017 Product grade A for the fully threaded shank portion of hexagon and hexagon flange headed bolts. ISO 4014 Product grade A for the head of hexagon headed products. 3.2 GAUGING REQUIREMENTS The gauging requirements shall be in accordance with the following standard

7、s: ISO 15071 for hexagon flange headed bolts. ISO 15071 for the shank portion of hexagon headed bolts. ISO 4017 Product grade A for the fully threaded shank portion of hexagon and hexagon flange headed bolts. ISO 4014 Product grade A for the head of hexagon headed products. 3.3 PROTECTIVE FINISH All

8、 dimensions and tolerances defined in this specification apply prior to the application of the protective finish except where otherwise specified. Note: For dimensions and tolerances of plated bolt threads see Clause 8. 4. LENGTH 4.1 BOLT & WASHER ASSEMBLIES Bolt & washer assemblies must be threaded

9、 to permit a ring gauge to be screwed to within a distance from the bearing face of the head not exceeding the free height of the assembled washer plus 2.5 x the thread pitch for lengths up to and including 2.5 x nominal size of the bolt thread, and 3 x the thread pitch for lengths greater than 2.5

10、x nominal size of the bolt thread. WORLDWIDE FASTENER STANDARDWA 900 Date: 2011 12 23 Copyright 2011, Ford Global Technologies, LLC Page 2 of 11 Printed copies are uncontrolled 5. DIAMETER OF SHANK (unthreaded portion). 5.1 BOLTS Reduced shank is the only shank design permitted unless otherwise spec

11、ified on a Utility drawing (no full shank constructions, see Foreword February 2003). 5.2 BOLT & WASHER ASSEMBLIES The diameter of the unthreaded portion of bolt & washer assemblies must be less than the major diameter of the bolt thread by an amount sufficient to permit free rotation of the washer,

12、 while disassembly from the bolt is prevented. The fillet type use for bolt and washer assemblies shall be at the discretion of the manufacturer provided all other requirements of the standard are met. 6. WASHERS The dimensions and tolerances of the washer component of bolt & washer assemblies must

13、conform to the data specified in the related Ford Standard or Utility Part drawing and WF 900. 7. UPPER SURFACE AND BEARING SURFACE OF HEADS The upper surfaces of heads may be flat or indented at the option of the manufacturer and shall be either chamfered or rounded. The diameter of the top circle

14、must not be greater than the maximum width across flats and not less than 85% of the minimum width across flats. Supplier identification and property class marking embossed or indented on the upper surface must comply with WA 950, unless otherwise specified on a Utility drawing. 8. BOLT THREAD CONFO

15、RMANCE 8.1 Bolt threads must conform to the dimensions and tolerances specified in ISO 261 and ISO 965, tolerance class 6g, unless otherwise specified on the part drawing. Acceptability of bolt thread gauging shall be determined according to ISO 1502. Acceptability of thread damage due to nicks and

16、gouges shall be determined according to WA 990. 8.2 Bolt threads with a protective finish may require additional allowance to accommodate thicker plating and/or coating. The additional allowances are specified in the WX 100 Finish Specification. 9. ENDS OF HEXAGON AND FLANGED HEXAGON BOLTS Unless ot

17、herwise specified, the ends of hexagon and flanged hexagon bolts shall be the Chamfered End design only. 10. PILOT POINT DIMENSIONS 10.1 LENGTH AND DIAMETER The length and diameter of pilot points shall be as specified in Table 1. 10.2 ENDS OF PILOT POINTS Ends of pilot points shall be flat or sligh

18、tly indented to permit normal material flow as illustrated in Figure 1. All other requirements shall conform to ISO 4753. WORLDWIDE FASTENER STANDARDWA 900 Date: 2011 12 23 Copyright 2011, Ford Global Technologies, LLC Page 3 of 11 Table 1 Size M3 M4 M5 M6 M8 M10 M12 M14 M16 M20 M24 nom 1.5 2.0 2.5

19、3.0 4.0 5.0 6.0 7.0 8.0 10.0 12.0 Length Lp +/- 0.25 0.25 0.25 0.25 0.3 0.3 0.3 0.4 0.4 0.4 0.4 max 2.0 2.9 3.75 4.5 6.1 7.8 9.3 11.1 13.2 16.3 19.6 Diameter dp min 1.7 2.70 3.55 4.30 5.90 7.60 9.00 10.8 12.9 15.9 19.2 Figure 1 Figure 2 - Thread length and thread end details of bolts Printed copies

20、are uncontrolled WORLDWIDE FASTENER STANDARDWA 900 Date: 2011 12 23 Copyright 2011, Ford Global Technologies, LLC Page 4 of 11 Printed copies are uncontrolled Table 2 - Thread length dimension of bolts Size M5 M6 M8 M10 M12 M14 M16 M20 M24 B ref 1)16 18 22 26 30 34 38 46 54 2)40 44 52 60 L Ls min Lg

21、 max LsminLgmax Lsmin LgmaxLsminLgMaxLsminLgmaxLsminLgmaxLsminLgmax Lsmin Lgmax LsminLgmax25 5 9 30 10 14 7 12 35 15 19 12 17 6.75 13 40 20 24 17 22 11.75 18 6.5 14 45 25 29 22 27 16.75 23 11.5 19 6.25 15 50 30 34 27 32 21.75 28 16.5 24 11.2 20 6 16 55 32 37 26.75 33 21.5 29 16.2 25 11 21 7 17 60 37

22、 42 31.75 38 26.5 34 21.2 30 16 26 12 22 65 36.75 43 31.5 39 26.2 35 21 31 17 27 6.5 19 70 41.75 48 36.5 44 31.2 40 26 36 22 32 11.5 24 75 46.75 53 41.5 49 36.2 45 31 41 27 37 16.5 29 80 51.75 58 46.5 54 41.2 50 36 46 32 42 21.5 34 11 26 85 51.5 59 46.2 55 41 51 37 47 26.5 39 16 31 90 56.5 64 51.2 6

23、0 46 56 42 52 31.5 44 21 36 95 61.5 69 56.2 65 51 61 47 57 36.5 49 26 41 100 66.5 74 61.2 70 56 66 52 62 41.5 54 31 46 105 66.2 75 61 71 57 67 46.5 59 36 51 110 71.2 80 66 76 62 72 51.5 64 41 56 120 81.2 90 76 86 72 82 61.5 74 51 66 130 80 90 76 86 65.5 78 55 70 140 90 100 86 96 75.5 88 65 80 150 96

24、 106 85.5 98 75 90 1) For L up to and including 125 2) For L greater than 125 Lsi min = 0.5 d (diameter) see table 5 11. DIAGRAMS AND TABLES TO ASSIST DESIGN ENGINEERING The following diagrams and tables have been included to assist Design Engineers. WORLDWIDE FASTENER STANDARDWA 900 Date: 2011 12 2

25、3 Copyright 2011, Ford Global Technologies, LLC Page 5 of 11 Figure 3 - Head detail of hexagon head boltsINDENTATION AND ITSSHAPE OPTIONALWASHER FACE ORCHAMFER OPTIONALCHAMFEROR FREE FLOWRADIUSTable 3 - Head dimensions of hexagon head bolts Size M4 M5 M6 M8 M10 M12 M14 M16 M20 M24 s max 7 8 10 13 15

26、 18 21 24 30 36 min 6.78 7.78 9.78 12.73 14.73 17.73 20.67 23.67 29.67 35.38 e min 7.66 8.79 11.05 14.38 16.77 20.03 23.36 26.75 33.53 39.98 k 1)max 2.925 3.65 4.15 5.45 6.58 7.68 8.98 10.18 12.715 15.215min 2.675 3.35 3.85 5.15 6.22 7.32 8.62 9.82 12.285 14.785k (kw) ref 1.87 2.35 2.70 3.61 4.35 5.

27、12 6.03 6.87 8.60 10.35 dw 2)min 5.88 6.88 8.88 11.63 13.63 16.63 19.64 22.49 28.19 33.61 c max 0.4 0.5 0.5 0.6 0.6 0.6 0.6 0.8 0.8 0.8 min 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.20 0.20 0.20 1) Embossed head markings (See WA 950) are excluded from head height measurements but must not protrude more t

28、han 0.4. 2) dwmax must not exceed dimension s actual. Printed copies are uncontrolled WORLDWIDE FASTENER STANDARDWA 900 Date: 2011 12 23 Copyright 2011, Ford Global Technologies, LLC Page 6 of 11 Figure 4 - Fillet and thread runout of fully threaded hexagon head bolts adaaaadrrDetail X. Alternative

29、thread runouts Xds Pitch dia.Permissible shapeTable 4 - Fillet and thread runout dimensions of fully threaded hexagon head bolts Size M4 M5 M6 M8 M10 M12 M14 M16 M20 M24 Pitch 0.7 0.8 1.0 1.25 1.5 1.75 2.0 2.0 2.5 3.0 a max 1)L2.5d 2.1 2.4 3.0 4.0 4.5 5.3 6.0 6.0 7.5 9.0 daMax 4.7 5.7 6.8 9.2 11.2 1

30、3.7 15.7 17.7 22.4 26.4 r Min 0.2 0.2 0.25 0.4 0.4 0.6 0.6 0.6 0.8 0.8 a max = The distance from the underhead bearing surface to the leading face of a thread ring gauge which has been screwed as far as possible onto the bolt by hand. a min = 1 Pitch Printed copies are uncontrolled WORLDWIDE FASTENE

31、R STANDARDWA 900 Date: 2011 12 23 Copyright 2011, Ford Global Technologies, LLC Page 7 of 11 Figure 5 - Fillet and shank details of partial threaded hexagon head bolts WASHER FACE ORCHAMFER OPTIONALLsiXdsdsifDetail Xda dsrNOTE: The radius under the head need not be a true radius providing that the c

32、urve is smooth and lies wholly within the shaded area shown in Detail X above, and must not extend into the bearing surface beyond the maximum transitional daspecified in Table 5. Table 5 - Fillet and shank dimensions of partial threaded hexagon head bolts Size M4 M5 M6 M8 M10 M12 M14 M16 M20 M24 da

33、max 4.7 5.7 6.8 9.2 11.2 13.7 15.7 17.7 22.4 26.4 f max 1.2 1.2 1.4 2.0 2.0 3.0 3.0 3.0 4.0 4.0 r min 0.2 0.2 0.25 0.4 0.4 0.6 0.6 0.6 0.8 0.8 dsmax 4 5 6 8 10 12 14 16 20 24 min 3.82 4.82 5.82 7.78 9.78 11.73 13.73 15.73 19.67 23.67 dsimax 3.6 4.5 5.6 7.4 9.4 11.2 13 15 19 23 min 3.4 4.3 5.2 7 8.9

34、10.7 12.5 14.5 18.2 21.8 Lsimin 2 2.5 3 4 5 6 7 8 10 12 Printed copies are uncontrolled WORLDWIDE FASTENER STANDARDWA 900 Date: 2011 12 23 Copyright 2011, Ford Global Technologies, LLC Page 8 of 11 Figure 6 - Head and flange details of hexagon flange bolts Table 6 - Head and flange dimensions of hex

35、agon flange bolts Size M5 M6 M8 M10 M12 M14 M16 s max 7 8 10 13 15 18 21 min 6.78 7.78 9.78 12.73 14.73 17.73 20.67 e min 7.59 8.71 10.95 14.26 16.5 19.86 23.15k 1)max 5.6 6.9 8.5 9.7 12.1 12.9 15.2 min 4.8 5.9 7.2 8.2 10.3 11.5 13 kwmin 2.3 2.9 3.8 4.3 5.4 5.6 6.8 dcmax 11.4 13.6 17 20.8 24.7 28.6

36、32.8 min cf1 1.1 1.2 1.5 1.8 2.1 2.4 t1.5 2 2 3 3 3.1 3.25 r22)max 0.3 0.4 0.5 0.6 0.7 0.9 1 1) Embossed head markings (See WA 950) are excluded from head height measurements but must not protrude more than 0.4. 2) Radius r2 applies both at the corners and at the flats of the hexagon. 3) The top of

37、the head shall be either full form or indented at the manufactures option and shall be either chamfered or rounded. The minimum diameter of the chamfer or start of rounding shall be the maximum width across flats minus 15%. If the top of the head is indented, the periphery may be rounded. Printed co

38、pies are uncontrolled WORLDWIDE FASTENER STANDARDWA 900 Date: 2011 12 23 Copyright 2011, Ford Global Technologies, LLC Page 9 of 11 Figure 7 - Fillet, bearing surface and thread runout details of fully threaded hexagon flange bolts Note: The fillet type is not an optional requirement, Type F fillet

39、shall be supplied for all parts unless the type U is specified on the part print or product standard. Figure 8 - Fillet, bearing surface and shank details of partial threaded hexagon flange bolts Note: The fillet type is not an optional requirement, Type F fillet shall be supplied for all parts unle

40、ss the type U is specified on the part print or product standard. Printed copies are uncontrolled WORLDWIDE FASTENER STANDARDWA 900 Date: 2011 12 23 Copyright 2011, Ford Global Technologies, LLC Page 10 of 11 Printed copies are uncontrolled NOTE: The radius under the head need not be a true radius p

41、roviding that the curve is smooth and lies wholly within the shaded area shown in Detail X above, and must not extend into the bearing surface beyond the maximum transitional diameter daspecified in Table 7. Table 7 - Dimensions Size M5 M6 M8 M10 M12 M14 M16 ISO Referencea max 1)L2.5d 2.4 3 3.8 4.5

42、5.3 6 6 4017 dwmin 9.4 11.6 14.9 18.7 22.5 26.4 30.6 15071 r1 min 0.2 0.25 0.4 0.4 0.6 0.6 0.6 15071 r3 min 0.10 0.11 0.16 0.20 0.24 0.28 0.32 15071 r4 ref 4.0 4.4 5.7 5.7 5.7 5.7 5.8 15071 damax2)Type F 5.7 6.8 9.2 11.2 13.7 15.7 17.7 15071 Type U 6.2 7.5 10 12.5 15.2 17.7 20.5 15071 dV max 5.5 6.6

43、 8.8 10.8 12.8 14.8 17.2 15071 ds max 5 6 8 10 12 14 16 15071 min 4.82 5.82 7.78 9.78 11.73 13.73 15.73 15071 V max 0.15 0.20 0.25 0.30 0.35 0.45 0.50 15071 min 0.05 0.05 0.10 0.15 0.15 0.20 0.25 15071 Lf max 1.4 1.6 2.1 2.1 2.1 2.1 3.2 15071 dsimax 4.5 5.6 7.4 9.4 11.2 13 15 15071 min 4.3 5.2 7 8.9

44、 10.7 12.5 14.5 15071 Lsi 3)min 2.5 3 4 5 6 7 8 15071 1) a max = The distance from the underhead bearing surface to the leading face of a thread ring gauge which has been screwed as far as possible onto the bolt by hand. a min = 1 Pitch 2) The minimum size hole required to prevent fillet interferenc

45、e is damax for Type F and dV max for Type U. 3) Lsi equals 0.5d+ 1/- 0.0 12. SUMMARY OF REVISIONS December 2011 Table 7, Note 2 clarified minimum hole size requirement August 2009 Updated the reference to ISO 6157 in Section 2 was updated to ISO 6157-3. In Table 3, the M10 dwdimension was corrected

46、to 13.63. March 2007 In the September 2006 update the following note was added to Figure 7 and Figure 8: Note: The fillet type is not an optional requirement, Type F fillet shall be supplied for all parts unless the type U is specified on the part print or product standard. Note: An audit of current

47、 production indicated that Type F fillets are normal production , type U is only being supplied when specifically requested. Prior to the clarification, if any part is being supplied with a type U undercut that is not specifically requested the PPAP process shall be used to change to type F and comp

48、ly with this standard. The following note was added to 5.2: The fillet type use for bolt and washer assemblies shall be at the discretion of the manufacturer provided all other requirements of the standard are met. Tables 7 & 8 were combined, and the ISO reference column was added. WORLDWIDE FASTENE

49、R STANDARDWA 900 Date: 2011 12 23 Copyright 2011, Ford Global Technologies, LLC Page 11 of 11 Printed copies are uncontrolled November 2005 In the November 2005 update, diagrams and tables showing the head dimensions were included in the standard. The intent is to make this information more readily available to our Design Engineers. Note Type B head style is ISO Type U. Type A head style is ISO Type F. Type C head style is the ISO Type F permissible alternativ