FORD S-M3D1009-A-2005 GLASS FIBER REINFORCED POLYESTER RESIN TO BE USED WITH FORD WSS-M99P1111-A 《玻璃纤维增强聚酯树脂 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD S-M3D1009-A-2005 GLASS FIBER REINFORCED POLYESTER RESIN TO BE USED WITH FORD WSS-M99P1111-A 《玻璃纤维增强聚酯树脂 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD S-M3D1009-A-2005 GLASS FIBER REINFORCED POLYESTER RESIN TO BE USED WITH FORD WSS-M99P1111-A 《玻璃纤维增强聚酯树脂 与标准FORD WSS-M99P1111-A一起使用 》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2005 06 21 Revised Inserted 3.0; Deleted 3.2.10 Removed Inactive S-M3D1009-B 1995 01 16 Revised and Retyped Was 7 pages1973 01 16 Released BC/M1517DLPrinted copies are uncontrolled Copyright 2005, Ford Global Technologies, LLC Page 1 of 3 GLAS

2、S FIBER REINFORCED POLYESTER RESIN S-M3D1009-A 1. SCOPE The material defined by this specification is a polyester resin reinforced with glass fibers, either randomly distributed or in the form of chopped strand mat, molded under low pressure conditions and incorporating on one surface a polyester re

3、sin gel coat free from glass fiber. 2. APPLICATION The material is generally used for molding exterior body panels such as headlamp bezels for commercial vehicles by hand lay-up similar “open“ techniques. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part

4、producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 MECHANICAL PROPERTIES Test specimens shall be cut from fully cured flat sheets produced as additional parts of production moldings, or from special panels manufactured separately using standar

5、d materials and fabrication conditions, both without the gel coat layer. Test specimens shall be conditioned to ISO R 291, 23 +/- 2 C and 50 +/- 5% relative humidity for 24 h prior to testing. Results for clauses 3.1.1 through to 3.1.4 inclusive shall be the average of at least 10 random samples. 3.

6、1.1 Tensile Strength, min 50 MN/m2(ISO R 527 Type 2 test specimens, pulling speed 5 mm/minute-1) 3.1.2 Impact Strength, min Notched 700 J/m (ISO R 180, Method A) 3.1.3 Flexural Strength, min 85 MN/m2(ISO R 178) 3.1.4 Modulus of Elasticity, min 3.75 GN/m2(ISO R 178 Tangent) 3.1.5 Hardness Barcol, min

7、 33 (ASTM D 2583) 3.1.6 Water Absorption, max 50 mg (ISO 62, Method B, 24 h total immersion 3 mm Thickness at 23 +/- 0.5 C) ENGINEERING MATERIAL SPECIFICATIONS-M3D1009-APrinted copies are uncontrolled Copyright 2005, Ford Global Technologies, LLC Page 2 of 3 3.2 MOLDED PART REQUIREMENTS The followin

8、g test requirements are applicable to fully cured molded parts and/or test specimens cut from molded parts complete with gel coat conditioned to ISO R 291, at 23 +/- 2 C and 50 +/- 5% relative humidity for 24 h prior to testing. 3.2.1 Surface Finish (Gel coated surface) Moldings shall be free from p

9、rotruding fibers, dirt, voids, pits, bubbles, cracks, blisters and resin rich or resin denuded areas. The gel coat shall adhere well to the underlying laminate and shall not exhibit any surface tackiness. 3.2.2 Long Term Waviness (Gel coated surface) Parts shall exhibit no more waviness than the For

10、d minimum acceptance part approved by the affected Product Engineering office. Test parts shall be painted with a paint having a specular gloss level A that is 92 units minimum by 60meter. 3.2.3 Tensile Strength, min 45 MN/m2(ISO R 527, Type 2 test specimens, pulling speed 5 mm minute-1) The result

11、shall be the average of four pieces cut from the flattest possible areas. 3.2.4 Flexural Strength, min 80 MN/m2(ISO R 178) The result shall be the average of four pieces cut from the flattest possible areas. 3.2.5 Glass Fiber Content, ww/, min 25% Sample: About 5 g sample material from which the gel

12、 coat has been removed by sanding is preconditioned at 100 C for 1 h before weighing. Method: After muffling at 575 +/- 25 C in a silica crucible till the residue is white, it is cooled and weighed. Further heating, cooling and weighing cycles are performed until constant weight (within 0.01 g). The

13、 residue is well washed with dilute (1:1) hydrochloric acid and the glass separated by filtration. After rinsing with water then acetone and drying at 100 C for 1 h the glass fiber is cooled and weighed accurately. Result: Express the result as the mean of four determinations expressed as percentage

14、 glass fiber by weight. 3.2.6 Thermal Cycling There shall be no visible cracking, separation, warping or exudation in either gel coat or laminate following ten cycles of the following conditions: 1) -40 +/- 1 C for 1 h 2) 23 +/- 2 C for 1 h 3) 80 +/- 2 C for 3 h 4) 38 +/- 1 C and 98 +/- 2% relative

15、humidity for 16 h ENGINEERING MATERIAL SPECIFICATIONS-M3D1009-APrinted copies are uncontrolled Copyright 2005, Ford Global Technologies, LLC Page 3 of 3 3.2.7 Resistance to Artificial Weathering (FLTM BO 101-01, 200 h exposure; rear non-appearance surface of the molding exposed) After exposure there

16、 shall be no evidence of leaching of resin when the sample is examined at X10 magnification or delamination of the gel coat. 3.2.8 Paintability Molded parts shall be processed in keeping with the best commercial practice to ensure good paintability i.e., “as molded“ surfaces shall be free from contaminants which would affect paint adhesion when painted in accordance with the released Ford Motor Company specification for painted glass fiber reinforced polyester plastics. 3.2.9 Flammability No flammability requirements