FORD OVERVIEW-2011 FECDS Version 28 Revision Overview (Version 28).pdf

《FORD OVERVIEW-2011 FECDS Version 28 Revision Overview (Version 28).pdf》由会员分享，可在线阅读，更多相关《FORD OVERVIEW-2011 FECDS Version 28 Revision Overview (Version 28).pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、Original Issue: 20111231 Copyright, Ford Motor Company. Latest Re-issue: 20111231 Overview Printed copies are uncontrolled. FECDS Version 28 Revision Overview Foreword Page ii Modified paragraph titled: Revision Procedure o FECDS will now have one annual release New issues of the standard will now b

2、e released on 31 December ONLY o Revisions Submissions will be received up until 31 August to be considered for the next release revisions received after that date may have to wait until the following release o Revision Submissions need to be sent to Chris Leaves () - The subject line should contain

3、 the following information including the standard number affected: “FECDS Revision to Standard A-1” Page iii Modified paragraph titled: Submitting Content Questions o All questions, including clarifications and interpretations, should be sent to Tom Miller, () o Content of the subject line has been

4、clarified to include: “FECDS Question always include Standard number if applicable Standard A-3 BOM/Stock List Paragraph 1.1 o Clarified types of parts and assemblies contained in the BOM (see Section 2 definitions o Removed last 2 lines from paragraph pertaining to traceability and correctness (Not

5、e: Content moved to paragraph 3.1.1) Section 2 o Removed “(Reserved)“ Paragraph 2.1 o Added definition for “Traceability“ Paragraph 2.2 o Added definition for “End-Item Assembly“ Paragraph 2.3 o Added definition for “Sub-Assembly“ Paragraph 2.4 o Added definition for “Component (interchangeable with

6、 the word part)“ Paragraph 2.5 o Added definition for “Serviceable Components“ Overview Engineering CAD content moved to 3.2.1 Paragraph 3.2.1 Was included with para 3.2 Paragraph 3.2.1.1 “SYMB (Symbol)“ - Was 3.2.1 Paragraph 3.2.1.1.1 - Was 3.2.1.1 Paragraph 3.2.2.1 “AMT (Amount)“ - Was 3.2.2 Parag

7、raph 3.2.3.1 “SHT (Sheet)“ - Was 3.2.3 Paragraph 3.2.3.1.1 - Was 3.2.3.1 FECDS Version 28 Revision Overview Return to TOC Original Issue: 20111231 Copyright, Ford Motor Company. Latest Re-issue: 20111231 Overview Printed copies are uncontrolled. Standard A-3 continued . . . Paragraph 3.2.3.1.1.1 “Ex

8、ception:“ - Was 3.2.3.1.1 Paragraph 3.2.4.1 “Name or Stock Size“ - Was 3.2.4 Paragraph 3.2.4.1.1 - Was 3.2.4.1 Paragraph 3.2.4.2.1 - Was 3.2.4.2 Paragraph 3.2.4.3.1 - Was 3.2.4.3 Paragraph 3.2.5.1 “Material“ - Was 3.2.5 Paragraph 3.2.5.1.1 - Was 3.2.5.1 o Added reference to Standard E-4, 2nd line fr

9、om the end of paragraph Figure A-3.2 o Updated some of the content under columns titled “Name or Stock Size“ and “Materials“ Standard C-3 Abbreviations and Symbols Paragraph 4.1 / Fig C-3.1 o Clarified use of Diamond P by adding “(previous validation)” to description o (NEW) Added Diamond D, pass-th

10、rough (deferred validation) requirement Paragraph 4.4.1 o Clarified usage of Pass-Through Requirements Paragraph 4.4.2.1 o Modified to include reference to Diamond-D o Modified bullets outlining conditions when the Diamond-D & Diamond-P modifiers could be used: square4 1st bullet now refers to Diamo

11、nd-P applications only square4 2nd bullet modified to clarify that , modified the condition to reference to both Diamond-D & Diamond-P in paragraph Paragraph 4.4.2.2 (NEW) o Added note requiring the appropriated note be used whenever Pass-Through modifiers are used Paragraph 4.4.2.2.1 (NEW paragraph

12、 for Diamond-P note) o Clarified required drawing note when Diamond-P is used Paragraph 4.4.2.2.2 (NEW) o Added required drawing note when Diamond-D is used Standard D-1 Dimensioning and Tolerancing ASME Paragraph 4.20, page D-1-4 o Added clarification to Restrained Condition FECDS Version 28 Revisi

13、on Overview Return to TOC Original Issue: 20111231 Copyright, Ford Motor Company. Latest Re-issue: 20111231 Overview Printed copies are uncontrolled. Standard D-1 continued . . . ASME Paragraph 5.5, page D-1-5 o Added clarification and requirements when using the Free-State Symbol Standard E-3 Brand

14、ing and Coding Paragraph 3.6 - MOTORCRAFT BRAND REMOVED FROM USE o Removed reference to Motorcraft brand Paragraph 3.8 o Removed content relative to Motorcraft brand paragraph now RESERVED Figure E-3.2.1 o Removed figure from drawing showing Motorcraft brand Figure E-3.6 o Removed figure containing

15、Motorcraft branding sizes Standard E-4 Material Identification & Material Code Parts Marking MAJOR Restructuring & Modifications throughout Standard Paragraphs 2.1 / 2.2 / 2.3 / 2.4 o Moved definitions of Build-to-Print / Gray Box / Black Box / Interfaces to Standard A-3 Paragraph 2.4 o “Interfaces“

16、 - was definition for “Serviceable components . . .“ Paragraph 2.5 o Modified paragraph to define “Finishes“ and not list specific examples Section 3.1 o Changed title to “Layout“ Was “Identification of Material Specifications and Notes“ Paragraphs 3.1.1 / 3.1.1.1 o Modified to address “Single Compo

17、nent Drawings“ - Was “Black Box Components“ & “Black Box Note“ o (NEW) Added “Optional“ practice to enclose material list with a box for added drawing clarity o Removed old related paragraphs 3.1.1.2 / 3.1.1.3 / 3.1.1.3.1 Paragraphs 3.1.2 / 3.1.2.1 o Modified to address “Assembly and Sub-Assembly Dr

18、awings“ - Was “Gray Box Components“ & “Gray Box Note“ o Removed old related paragraphs 3.1.2.2 / 3.1.2.3 / 3.1.3 & all sub-paragraphs FECDS Version 28 Revision Overview Return to TOC Original Issue: 20111231 Copyright, Ford Motor Company. Latest Re-issue: 20111231 Overview Printed copies are uncontr

19、olled. Standard E-4 continued . . . Paragraph 3.2 (NEW) o Modified to address “Identification of Materials and Notes“ - Was addressing “Material Related Drawing Notes“ o Added note clarifying who is responsible for designating components as Build-to-Print, Gray Box or Black Box. Also states that it

20、is possible to have multiple applications of component types within an Assembly drawing. Paragraphs 3.2.1 / 3.2.1.1 / 3.2.1.2 o Modified to address “Build-to-Print Components, Material Identification“ Was addressing “Material Related Drawing Notes“ Paragraphs 3.2.2 / 3.2.2.1 / 3.2.2.2 / 3.2.2.3 o Mo

21、dified to address “Gray Box Components, Material Identification“ Was “Identifying Materials on Assembly and Sub-assembly Drawings“ o (NEW) Added material identification requirements for Gray Box Components o (NEW) Gray Box note NO LONGER REQUIRED Paragraphs 3.2.3 / 3.2.3.1 o Modified to address “Bla

22、ck Box Components, Material Identification“ Was “Identifying Material-Related Secondary Operations“ o NEW) Added material identification requirements for Black Box Components o (NEW) Black Box Note NO LONGER REQUIRED o Removed old related paragraphs 3.2.3.1.1 / 3.2.3.1.2 o V27 Heat Treatment Note pa

23、ra 2.3.2.2 and related sub-paragraphs moved to para 3.3 and related sub-paragraphs Paragraphs 3.2.4 / 3.2.4.1 o Modified to address “Format for Industry Standards“ Was “Identifying Cast Material Information“ o Removed old related paragraphs 3.2.4.1.1 / 3.2.4.2 / 3.2.4.3 Paragraphs and all related su

24、b-paragraphs 3.2.5 thru 3.2.6 removed content found in new renumbered in V28 Paragraphs 3.3 / 3.3.1- 3.3.5 o Modified to address “Heat Treatment Note“ Was “Material Code Parts Marking“ V27 Paragraphs numbered 3.2.5 thru 3.3.9 and all related sub-paragraphs removed content found in new numbered parag

25、raphs FECDS Version 28 Revision Overview Return to TOC Original Issue: 20111231 Copyright, Ford Motor Company. Latest Re-issue: 20111231 Overview Printed copies are uncontrolled. Standard E-4 continued . . . Paragraph 3.4 o Added to address “Identifying Cast Material Information“ Was para 3.2.4.1 in

26、 V27 Paragraphs 3.4.1 / 3.4.1.1 / 3.4.2 / 3.4.3 o Added to address “Casting Process Note“ Was para 3.2.4.1 & related sub-paragraphs in V27 Paragraph 3.5 o Added to address “Identifying Ford Motor Company Material Specifications“ Was para 3.2.5 in V27 Paragraphs 3.5 / 3.5.1 / 3.5.1.1 o Added to addre

27、ss “Material Source Note“ Was paragraphs 3.2.5.1 & 3.2.5.1.1 in V27 Paragraph 3.6 o Added to address “Identifying Hydrogen Embrittlement Requirements“ - Was para 3.2.6 in V27 Paragraphs 3.6.1 / 3.6.2 o Added to address “Hydrogen Embrittlement Note“ Was paragraphs 3.2.6.1 & 3.2.6.1.1 in V27 Paragraph

28、s 3.6.3 / 3.6.4 / 3.6.5 o Added to address “Embrittlement Exemption Callout“ Was paragraphs 3.2.6.1.2 & 3.2.6.1.2.1 in V27 Paragraphs 3.7 o Added to address “Material Code Parts Marking“ Was para 3.3 in V27 Paragraphs 3.7.1 & related sub-paragraphs o Added to address “Material Code Symbology“ Was pa

29、ra 3.3.1 & related sub-paragraphs in V27 Paragraphs 3.7.2 & related sub-paragraphs o Added to address “Material Code Symbol Location and Size on the Manufactured Part“ was para 3.3.3 & related sub-paragraphs in V27 Paragraphs 3.8 & related sub-paragraphs o Added to address “Polymeric Material Code P

30、arts Marking“ Was para 3.3.4 & related sub-paragraphs in V27 Paragraphs 3.9 / 3.9.1 & related sub-paragraphs o Added to address “Polymeric Material Code Note“ Was para 3.3.4.4 & related sub-paragraphs in V27 FECDS Version 28 Revision Overview Return to TOC Original Issue: 20111231 Copyright, Ford Mo

31、tor Company. Latest Re-issue: 20111231 Overview Printed copies are uncontrolled. Standard E-4 continued . . . Paragraph 3.9.2 o Added to address “Identification of Polymeric Materials with Post-Consumer Recycled Content (Reserved)“ Was para 3.3.5 in V27 Paragraphs 3.9.3 & related sub-paragraphs o Ad

32、ded to address “Identification of Polymeric Materials with Regrind Content“ Was para 3.3.6 & related sub-paragraphs in V27 Paragraphs 3.9.3.4 & related sub-paragraphs o Added to address “ Polymeric Regrind Content Note“ Was para 3.3.6.2 & related sub-paragraphs in V27 Paragraphs 3.9.4 & related sub-

33、paragraphs o Added to address “Identification of Polymeric Materials of Foam Polymeric Parts“ Was para 3.3.7 & related sub-paragraphs in V27 Paragraphs 3.9.5 & related sub-paragraphs o Added to address “Identification of Polymeric Materials of Laminated Polymeric Parts“ Was para 3.3.8 & related sub-

34、paragraphs in V27 Paragraphs 3.9.6 / 3.9.6.1 o Added to address “Examples of Polymeric Material Identification and Marking“ Was para 3.3.9 & related sub-paragraphs in V27 Standard F-2 Electrical and Electronics System Engineering Paragraph 3.4.1.3.1 o Modified header title to: “Circuit Count and Har

35、ness Weight Notes“ Was “Circuit Count Note“ o Added Harness Weight note and requirements Standard F-8 Body CAD Drawing Standards Official Standard - DRAFT Removed Paragraph 4.3.45 (NEW) o Added header: Adhesive, Interior Performance Note Paragraph 4.3.45.1 (NEW) o Added note Paragraph 4.6.5.1 o Modi

36、fied to state that a note is required when addressing BIW GDT requirements o Added pilot programs for EU and NA to apply ESBU5A-1294-AA specification FECDS Version 28 Revision Overview Return to TOC Original Issue: 20111231 Copyright, Ford Motor Company. Latest Re-issue: 20111231 Overview Printed co

37、pies are uncontrolled. Standard F-8 continued . . . Paragraph 4.6.6.1 o Added statement that when GDT ES for sheet metal will be obsolete Paragraph 4.6.7 o Removed “(NA Only)” Paragraph 4.6.7.1 o Removed parenthetical reference to NA region only Paragraph 4.6.8 o Removed content and sub-paragraph 4.

38、6.8.1 Now “Reserved” Section 4 & Sub-Paragraphs (NEW) o Added note titles and notes, where available Appendix C Proposals for Revisions Page C-1 MAJOR REVISION o Removed instructions and related figure used when accessing obsolete website () o Instructions for Revision Proposals have been updated se

39、e Standard for details Page C-2 o Updated figure of the downloadable Revision Submission example Page C-3 o Modified flow chart to reflect changes to the Revision Proposal process Appendix D Ford Engineering CAD and Drafting Standards Committee Charter Updated Committee Charter o Added additional re

40、quirements for Standard Sponsors Appendix N Drawing Note Quick Reference Page Appendix N-1 o C3: Updated link to “Diamond P Note for Pass-through (Previous Validation Requirement“ o (NEW) C3: Added note and link to “Diamond D Note for Pass-through (Deferred Validation) Requirement“ Page Appendix N-4

41、 o E-4: Removed Black Box Note & Gray Box Note (shows strike through until FECDS V29) FECDS Version 28 Revision Overview Return to TOC Original Issue: 20111231 Copyright, Ford Motor Company. Latest Re-issue: 20111231 Overview Printed copies are uncontrolled. Page Appendix N-4 continued: o E-4: Updat

42、ed links to the new paragraphs for the following notes referenced in the standard: Heat Treatment Note / Casting Process Note / Material Source Note / Hydrogen Embrittlement Note / Embrittlement Exemption Callout / Polymeric Material Code Note / Polymeric Regrind Content Note Page Appendix N-5 o F-2: Modified title of “Circuit Count and Harness Weight Notes“ and added the Harness Weight Note Appendix Z Record of Revision Added general revisions made to Version 28 (NEW) FECDS Version 28 Revision Overview Return to TOC