FORD M99C111-A (H)-2009 CALIBRATING FLUID - FUEL INJECTOR《燃料喷射器校准液》.pdf

《FORD M99C111-A (H)-2009 CALIBRATING FLUID - FUEL INJECTOR《燃料喷射器校准液》.pdf》由会员分享，可在线阅读，更多相关《FORD M99C111-A (H)-2009 CALIBRATING FLUID - FUEL INJECTOR《燃料喷射器校准液》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 NON-PRODUCTION MATERIAL SPECIFICATION Material Name Specification Number Date Action Changes 2009 06 24 N-STATUS No Replacement Named L. Sinclair, NA 1987 12 01 Page 1 of 2 CALIBRATING FLUID - FUEL INJECTOR M99C111-A(H) NOT TO BE USED FOR NEW DESIGN 1. SCOPE: The material defined by this standard i

2、s a highly refined and controlled petroleum product for use as a calibration fluid. 2. APPLICATION: This material is used in calibration stands for testing of fuel injectors. 3. REQUIREMENTS: 3.1 VISCOSITY MM2/S (CST) 37.8 C: 0.9 - 1.0 (ASTM D 443) 3.2 API GRAVITY 15.6/15.6 C: 46.5 - 51 (ASTM D 4052

3、) 3.3 SPECIFIC GRAVITY 15.6/15.6 C: .775 - .795 (ASTM D 4052) 3.4 COPPER STRIP CORROSION 3 HR., 100 C: 1B max (ASTM D 130) 3.5 SULFUR, WT PERCENT: .001 max (ASTM D 3120) 3.6 FLASH POINT C: 40 min (ASTM D 92) 3.7 FIRE POINT C: 40 min (ASTM D 92) 3.8 DISTILLATION RANGE C: (ASTM D 86) Percent Evaporati

4、on: Temperature Range C: IBP 153 min 10 % 158 - 161 50 % 161 - 166 90 % 168 - 172 EP % 180 max NON-PRODUCTION MATERIAL SPECIFICATION M99C111-A (H) Page 2 of 2 3.9 GUM CONTENT MG/100 ML: (ASTM D 381) Washed 1.3 max Unwashed 30 max 3.10 OXIDATION STABILITY: 1200 minutes (ASTM D 525) 3.11 INFRARED SPEC

5、TROPHOTOMETRY: Ford Motor Company, at its option, may conduct infrared analysis of material supplied to this specification. The curves established for initial approval shall constitute the reference standard and shall be kept on file at Central Laboratory. All samples shall produce curves that corre

6、spond to the reference standard when tested under the same conditions as those specified on the master curve. 3.12 SUPPLIERS RESPONSIBILITY: All materials supplied to this standard must be equivalent in all characteristics to the material upon which approval was originally granted and shall be suita

7、ble for the intended application. Changes in composition shall not be made without approval of the responsible Staff Office in accordance with Manufacturing Procedure IId1. 3.16 IDENTIFICATION: Materials supplied to this standard shall be identified with the “M“ number printed on the side as well as

8、 the top of the containers in letters at least 2 inches (50 mm) high in a contrasting color to that of the container. Container marking shall be in accordance with Manufacturing Standard ZF-10 and conform to all Federal, State and Local container contents labeling regulations which are in effect bot

9、h in the area of shipment and use. 4. APPROVAL OF NEW SUPPLIERS: Materials submitted by new manufacturers to this standard must have Regulatory Clearance, Laboratory and Shop Trial approvals. Suppliers are required to complete and submit the Material Health Safety and Environmental Data Sheet (Form

10、1291A) prior to Shop Trial. Recommendations for addition of new manufacturers to the Manufacturing Approved Source List (ASL) must be made in writing to the responsible Staff Office by the appropriate divisional standard activity in accordance with Manufacturing Procedure IId1. 5. ENVIRONMENTAL CONT

11、ROL: Use of any material approved to this standard must comply within the guidelines as established in environmental review of the material as they appear in the Materials and Toxicology System (MATS). 6. HEALTH AND SAFETY: Use of any material to this standard must comply with the guidelines given under the Toxicological (TOX) review of the material as indicated in the MATS system.