FORD FLTM BV 003-2-2001 TEST FOR VISCOSITY OF MASTIC TYPE BODY DEADENERS.pdf

《FORD FLTM BV 003-2-2001 TEST FOR VISCOSITY OF MASTIC TYPE BODY DEADENERS.pdf》由会员分享，可在线阅读，更多相关《FORD FLTM BV 003-2-2001 TEST FOR VISCOSITY OF MASTIC TYPE BODY DEADENERS.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、FORD LABORATORY TEST METHOD BV 003-02 2001 10 31 2000 08 11 TEST FOR VISCOSITY OF MASTIC TYPE BODY DEADENERS Revised Editorial - no technical change A. Cockman Revised Editorial - no technical change A. Cockman Application This procedure is used to determine the viscosity of mastic type body deadene

2、rs. The time required for 50 g of the material to pass through a Castor Severs Orifice (ASTM D 1823) under a pressure of 1 O psi indicates the viscosity of the mastic deadener. Apparatus Required 1. Pressure Flowmeter - an acceptable type of pressure flow apparatus is shown in the attached diagram.

3、Source: William Keil Mfg. Co. Warren, MI Note: Castor Severs #I 8207 calibrated 1/8 inch rheometer orifice meets specified orifice requirements. Pressure flowmeter described in SAE ADS 1 .I or Caster Severs Extrusion Rheometer Type A-I O0 may be used for this test. Source: Castor Engineering Co. Pit

4、tsburgh, PA 2. Stopwatch or similar timing device, accurate to 0.1 s. 3. Balance - laboratory bench type, triple beam single or double pan; metric beam scale. Capacity to 100 g min; sensitivity 0.1 g. 4. Supply line source of filtered dry compressed air capable of minimum pressure 30 psi 5. Thermome

5、ter with range inclusive of 79 OF. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 OC and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherw

6、ise specified. I Date I Action I Revisions I I 19920811 I I Copynght02001, Ford Global Technologies, Inc FORD LABORATORY TEST METHOD BV 003-02 1. 2. 3. 4. 5. 6. Procedure Connect flowmeter to air supply, using approximately 30 psi line pressure. Close cup air input valve and adjust air pressure regu

7、lator until flowmeter air gage reads 1 O Ibs/square inch. Place center of balance weighing pan 3.0 inches under the orifice and counterbalance a sheet of nonabsorbent paper on the pan. Set balance to weigh 50 g. Mix sample thoroughly in a one quart friction top can. Cover top tightly to prevent vola

8、tile loss and adjust sample to 77 +/- 2 OF. Fill cylindrical cup to 1/2 inch from top, tamping sharply to avoid air pocket formation. Place the flowmeter piston disc or follower plate on the sample surface and return filled cup into place on flowmeter. Open air valve to piston and extrude 50 g of sa

9、mple onto paper on balance pan. While sample is extruding, adjust air pressure regulator so that flowmeter air gage reads exactly 10 psi under load conditions. Discard this sample and replace a clean tared paper to the balance pan and reset balance to weigh 50 g net weight. Open air valve to piston

10、and extrude a 50 g sample. Start stopwatch when sample reaches tared paper and stop when balance indicator touches equilibrium point. Close piston valve and record time in seconds. The time required to extrude the second sample will be recorded as the flow rate or viscosity of the material. Addition

11、al determinations should not be made on any sample remaining in cup. If a recheck test is required, refill cleaned cup with fresh sample and repeat procedure. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for deter

12、mining proper use and handling in its facilities. Page 2 of 4 Copyright 02001, Ford Global Technologies, Inc FORD LABORATORY TEST METHOD BV 003-02 TEST FOR VISCOSITY OF MASTIC TYPE BODY DEADENERS Page 3 of 4 Copyright 02001, Ford Global Technologies, Inc FORD LABORATORY TEST METHOD BV 003-02 TEST FO

13、R VISCOSITY OF MASTIC TYPE BODY DEADENERS CAP (-DRILL 7/16“ TAP 1/4“ NPT 1_ KNURL “O“ RI N G THREAD 1-7/8“ 12T CAE - UN - CL.IA .FOLLOWER BARREL PLATE LBS - “O“ RING ORIFICE ASSY CASTOR SEVERS ASTM D 1823-61 1 ORIFICE ASSY FOR CASTOR SEVERS I ASTM D 1823-61 -T FORD BV3-2 1/8“ DIA. BORE THREAD 1-7/8“ x 12T SAE-UN-CL-I B DRILL 11/32“ TAP 3/8“ x 24 T. NF Kl nr REAM NO. 37 REAMER.104 +/- ,001 BORE NO. 38 DRILL Page 4 of 4 Copyright 02001, Ford Global Technologies, Inc