FORD FLTM BO 021-04-2001 IMPACT RESISTANCE OF PLASTIC VALVE STEM SEALS《塑料阀门杆密封件的耐冲击性》.pdf

《FORD FLTM BO 021-04-2001 IMPACT RESISTANCE OF PLASTIC VALVE STEM SEALS《塑料阀门杆密封件的耐冲击性》.pdf》由会员分享，可在线阅读，更多相关《FORD FLTM BO 021-04-2001 IMPACT RESISTANCE OF PLASTIC VALVE STEM SEALS《塑料阀门杆密封件的耐冲击性》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 FORD LABORATORY TEST METHOD BO 021-04 Date Action Revisions 2001 03 27 Revised Editorial no technical change A. Cockman 1992 07 27 Printed copies are uncontrolled Page 1 of 7 Copyright 2001, Ford Global Technologies, Inc. IMPACT RESISTANCE OF PLASTIC VALVE STEM SEALS Application This procedure is d

2、esigned to obtain the impact strength of glass filled or other reinforcing material in nylon or other plastic valve stem panels. Equipment Required Oven Mechanical convection, temperature range 38 - 260 C. Charpy Izod Impact Tester for Plastics or equivalent (ASTM D 256) Source: Tinius Olsen Easton

3、Road Willow Grove, Pennsylvania Fixture for Impact Tester Refer to drawings and photographs. Fixture “A“ Weight must be held to 110 +/- 10 g. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % re

4、lative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. Procedure 1. Stabilize the valve stem seals at temperature specified in the Engineering Drawing or specification. 2. Remove existing striking bit on end of the arm and replace it

5、with a one piece Fixture “A“ weight which must be 110 +/- 10 g. FORD LABORATORY TEST METHOD BO 021-04 Page 2 of 7 Copyright 2001, Ford Global Technologies, Inc. 3. Install valve stem seal in Fixture B, C and D with the minor diameter facing the striker arm. Installation torque must be .03 Nm. 4. Ins

6、tall Fixture B, C, and D and sample in the machine holding jaw. 5. Set Charpy Izod dial to 100 range and install weights marked 100. 6. Trip arm and record impact values. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsib

7、le for determining proper use and handling in its facilities. FORD LABORATORY TEST METHOD BO 021-04 Page 3 of 7 Copyright 2001, Ford Global Technologies, Inc. IMPACT RESISTANCE OF PLASTIC VALVE STEM SEALS FORD LABORATORY TEST METHOD BO 021-04 Page 4 of 7 Copyright 2001, Ford Global Technologies, Inc

8、. IMPACT RESISTANCE OF PLASTIC VALVE STEM SEALS FORD LABORATORY TEST METHOD BO 021-04 Page 5 of 7 Copyright 2001, Ford Global Technologies, Inc. IMPACT RESISTANCE OF PLASTIC VALVE STEM SEALS FORD LABORATORY TEST METHOD BO 021-04 Page 6 of 7 Copyright 2001, Ford Global Technologies, Inc. IMPACT RESIS

9、TANCE OF PLASTIC VALVE STEM SEALS PLASTIC VALVE STEM SEAL Photograph showing Fixture used for Testing Plastic Valve Stem Seal. FORD LABORATORY TEST METHOD BO 021-04 Page 7 of 7 Copyright 2001, Ford Global Technologies, Inc. IMPACT RESISTANCE OF PLASTIC VALVE STEM SEALS PLASTIC VALVE STEM SEAL Photograph showing Fixture used for Testing Plastic Valve Stem Seal.