FORD FLTM BN 161-01-2011 STEERING WHEEL WEAR RUB TEST《方向盘磨损摩擦试验》.pdf

《FORD FLTM BN 161-01-2011 STEERING WHEEL WEAR RUB TEST《方向盘磨损摩擦试验》.pdf》由会员分享，可在线阅读，更多相关《FORD FLTM BN 161-01-2011 STEERING WHEEL WEAR RUB TEST《方向盘磨损摩擦试验》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 FORD LABORATORY TEST METHOD BN 161-01 Date Action Revisions Rev. 0 2011 02 24 Active B. Haggart, NA Printed copies are uncontrolled Copyright 2011, Ford Global Technologies, LLC Page 1 of 5 STEERING WHEEL WEAR RUB TEST Application This procedure is used to determine the wear resistance of steering

2、wheel materials. Apparatus Required Wear Rub Test Machine The Wear Rub Machine (Figure 1) has a mounting position for whole steering wheels (Figure 2) as well as a fixture for mounting wheel wrap materials on a 25.4 mm diameter metal dowel (Figure 3). A motor with a rotating arm pulls a strip of cot

3、ton duck cloth back and forth across the sample similar to a shoe shine. A free weight attached to one end of the cloth provides the force. A counter will automatically turn off the machine after a preset number of cycles. Source: Equipment is custom made, no specific manufacturer. Unit shown in Fig

4、ure 1 was made at Ford Motor Company. Steering wheel manufacturers typically have similar machines. #10 Cotton Duck Cloth: Style 426-ACT, 44.5 +/- 2 mm wide Source: Test Fabrics Inc. PO Box 26 West Pittston, PA 18643, US PHONE: (570)603-0432 Purell Instant Hand Sanitizer 65% Ethyl Alcohol (or equiv

5、alent) Source: Johnson & Johnson Consumer Companies PHONE: 1-800-223-0812 Burette, 50 ml or larger Or other device for dispensing water onto the cloth. Sample Description The following samples may be tested depending on the requirements in the Material Engineering Specification or for other investi

6、gations on wear performance. 1. 76 x 76 mm material sample for mounting on dowel 2. Steering wheel (Used to test painted urethane wheels or field returns) FORD LABORATORY TEST METHOD BN 161-01 Printed copies are uncontrolled Copyright 2011, Ford Global Technologies, LLC Page 2 of 5 Conditioning and

7、Test Conditions All testing is based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing after sample receipt or after any preconditioning steps. Modifications of the test method must be noted in detail on the test

8、 report. Procedure 1. Soak a length of 44.5 +/- 2 mm wide duck cloth in water until saturated. 2. Condition a 76 x 76 mm sample of material for 10 minutes in 55 +/- 1C water. This step is omitted for steering wheels. 3. Remove and secure onto a 25.4 mm dowel. The sample may be held in place by clamp

9、s. The material should be held taught and stationary during the test. Steering wheels are mounted directly to the machine. 4. Position the duck cloth so it covers 180 of the sample without touching the seam. Weight the free end of the cloth with a 1.36 +/- 0.05 kg (3lb) mass and attach the other end

10、 to the reciprocating machine. 5. Ensure a smooth stroke with a length of 95 +/- 2 mm. One rise and fall of the weight equals one reciprocating stroke. The test shall run at 50 +/- 2 reciprocating strokes per minute. 6. Run the test for 1,500 reciprocating strokes in an ambient air temperature of 23

11、 +/- 3C. 7. Keep the cloth saturated with room temperature water to prevent the sample from overheating and to maintain a constant coefficient of friction. 8. Record number of cycles when wear becomes apparent. Suggest checking every 500 cycles. 9. Test a total of 3 specimens using a new cloth for e

12、ach. Procedure for Samples with Hand Sanitizer 1. Secure 76 x 76 mm material sample onto 25.4 mm dowel. The sample may be held in place by clamps. The material should be held taught and stationary during the test. Steering wheels may also be used in place of the material sample. 2. Weigh out approxi

13、mately 3 grams of gel hand sanitizer and apply it to a plastic panel (Figure 4) to cover an area 44.5 mm wide and 200 mm in length as uniformly as possible. Work quickly to minimize evaporation of the sanitizer 3. Place the duck cloth on the plastic panel (Figure 5) so that the middle area of the cl

14、oth is over the hand sanitizer. Press the duck cloth into the sanitizer to saturate the cloth. 4. Position the cloth so it covers 180 of the sample without touching the seam. Weight the free end of the cloth with a 1.36 +/- 0.05 kg (3lb) mass and attach the other end to the reciprocating machine. 5.

15、 Ensure a smooth stroke with a length of 95 +/- 2 mm. One rise and fall of the weight equals one reciprocating stroke. The test shall run at 50 +/- 2 reciprocating strokes per minute. 6. Start the Wear Rub Machine within 1 to 2 minutes after saturating the cloth. FORD LABORATORY TEST METHOD BN 161-0

16、1 Printed copies are uncontrolled Copyright 2011, Ford Global Technologies, LLC Page 3 of 5 7. Check for wear and reapply hand sanitizer every 500 reciprocating strokes as done in steps 2 and 3. Run the test for a total of 1,500 reciprocating strokes at an ambient air temperature of 23 +/- 3 C. 8. R

17、ecord number of cycles when wear becomes apparent. Suggest checking every 500 cycles. 9. Test a total of 3 specimens using a new cloth for each. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper

18、use and handling in its facilities. Figure 1: Wear Rub Testing Apparatus 1.36 kg Sample Dowel Duck Cloth Motor Rotating Arm FORD LABORATORY TEST METHOD BN 161-01 Printed copies are uncontrolled Copyright 2011, Ford Global Technologies, LLC Page 4 of 5 Figure 2: Steering Wheel Fixture Figure 3: Wheel

19、 Wrap Mounted Sample Fixture FORD LABORATORY TEST METHOD BN 161-01 Printed copies are uncontrolled Copyright 2011, Ford Global Technologies, LLC Page 5 of 5 Figure 4: Hand Sanitizer Application to Plastic Panel Spread sanitizer evenly over area of the plastic panel. Figure 5: Hand Sanitizer Application to Duck Cloth Press middle section of duck cloth into hand sanitizer to saturate the duck cloth.