FORD EST-M1L103-A-2003 COPPER WIRE - BATTERY CABLE - #3 GAGE TO BE USED WITH FORD WSS-M99P1111-A 《电池电缆用铜丝》.pdf

《FORD EST-M1L103-A-2003 COPPER WIRE - BATTERY CABLE - #3 GAGE TO BE USED WITH FORD WSS-M99P1111-A 《电池电缆用铜丝》.pdf》由会员分享，可在线阅读，更多相关《FORD EST-M1L103-A-2003 COPPER WIRE - BATTERY CABLE - #3 GAGE TO BE USED WITH FORD WSS-M99P1111-A 《电池电缆用铜丝》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2003 04 29 Revised Para 3.0 inserted; Para 3.9 & 4 deleted 1978 08 30 Metricated & Retyped 1976 09 14 Released HG2-00NA-250 Orig./s/K. GillisPrinted copies are uncontrolled Page 1 of 2 Copyright 2003, Ford G

2、lobal Technologies, Inc. COPPER WIRE - BATTERY CABLE - #3 GAGE EST-M1L103-A 1. SCOPE The material defined by this specification is stranded insulated battery cable. 2. APPLICATION This specification was released originally for battery cables on heavy duty installations. 3. REQUIREMENTS 3.0 STANDARD

3、REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 CABLE SIZES The finished cable diameter shall not exceed 0.48 in (12.2 mm). 3.2 CABLE QUALITY Shall meet all the requirements

4、listed herein and must be equal to the original approved samples. 3.3 CABLE CONSTRUCTION Shall consist of 518 strands (nominal of #30 gage round wire layed in rope construction and served with 1 x 0.003 in (25.4 x 0.08 mm) minimum paper tape with 12-1/2% minimum overlap. Absolute minimum number of s

5、trands at any one time to be 515. No individual group is to contain more than 20% of the total strands. Minimum area is 51 548 cmil (26.12 mm2). 3.4 WIRE QUALITY The conductor strands prior to stranding or bunching shall consist of bare ESF-M2L1-A, soft or annealed round copper wire. 3.5 INSULATION

6、COLOR Black, unless otherwise specified on the engineering drawing. ENGINEERING MATERIAL SPECIFICATION EST-M1L103-A Page 2 of 2 Copyright 2003, Ford Global Technologies, Inc. 3.6 INSULATION QUALITY The neoprene or vinyl-nitrile insulation must meet all basic SAE J 558 type SGR requirements and have

7、a nominal wall thickness of 0.080 in (2.03 mm). 3.7 RESISTIVITY at 20 C, max 211 /ft (692 /m) 3.8 PHYSICAL AND ELECTRICAL PROPERTIES Three samples of cable are required. One for high temperature, low temperature and oil absorption tests. All samples are subjected to the dielectric breakdown test at

8、the completion of their respective tests. These samples are 24 in (0.6 m) in length with 1 in (25 mm) of insulation stripped from both ends. 3.8.1 High Temperature Resistance Suspend sample over a 10 in (254 mm) mandrel with a 6 lb (2.72 kg) weight at each end. Soak at 121 +/- 1 C for 120 h in a cir

9、culating air oven. Cool to room temperature, remove the weight and bend the sample around the mandrel in a reverse direction at a rate not exceeding 1 turn per minute until a 180 bend is completed. Insulation shall not fracture or split. 3.8.2 Low Temperature Resistance Lower the temperature on a st

10、raight piece of sample to -34 C at a rate not to exceed 68 C per minute. Hold for 3 h and then wrap around a 10 in (254 mm) mandrel at 6 turns per minute for 180. Insulation shall not fracture. 3.8.3 Oil Absorption Resistance Immerse sample to within 1-1/2 in (38 mm) from the ends into a solution of

11、 50% kerosene, 50% SAE 10W engine oil for 20 h at 49 +/- 1 C. The cable diameter shall not increase more than 15%. Wrap sample around a 10 in (254 mm) mandrel for 180. Insulation shall not fracture or split. 3.8.4 Dielectric Resistance Join exposed ends of sample and immerse loop to within 6 in (150 mm) of ends in a 5% salt bath (salt content weight at 27 C). Soak 5 h and then apply 500V (RMS) 60 cps (Hz) between sample conductor and salt bath for 1 minute. Insulation shall not rupture.