FORD ESR-M5B194-B-2002 CLEANER - BRIGHT METAL TO BE USED WITH FORD WSS-M99P1111-A 《光亮金属清洁剂 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD ESR-M5B194-B-2002 CLEANER - BRIGHT METAL TO BE USED WITH FORD WSS-M99P1111-A 《光亮金属清洁剂 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD ESR-M5B194-B-2002 CLEANER - BRIGHT METAL TO BE USED WITH FORD WSS-M99P1111-A 《光亮金属清洁剂 与标准FORD WSS-M99P1111-A一起使用 》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2002 08 19 Revised Updated and renumbered 1979 03 20 Revised & Retyped CP022-815800-4 1971 03 29 Released CPZ22-947987-1 Printed copies are uncontrolled Page 1 of 3 Copyright 2002, Ford Global Technologies,

2、Inc. CLEANER - BRIGHT METAL ESR-M5B194-B 1. SCOPE The material described by this specification is a cleaner used to clean automotive bright metal trim and is not intended to limit the cleaner to any specific material or material system, but rather defines the performance of the entire system. 2. APP

3、LICATION This specification was released originally for material used for cleaning chromium, stainless steel and nickel-plated parts. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Produc

4、tion Materials (WSS-M99P1111-A). 3.2 Shall be in a ready-to-use form, of homogeneous composition and free of foreign matter. 3.3 Shall be no objectionable odor either during or after application of the material. 3.4 Must effectively remove, with a minimum of time and effort, all deposits normally en

5、countered on exterior and interior automotive bright metals. 3.5 Shall not etch, scratch, mar or have any detrimental effect on any metal surface to which it is applied. 3.6 Shall be easily removed by wiping, after drying, and shall have restored the original metal luster. 3.7 Adequate warning shall

6、 be provided on the label to prevent prolonged contact of this material on painted surfaces, if necessary. 3.8 Shall have no detrimental effect on automotive parts it may come in contact with, such as glass, fabric, rubber or other associated materials. 3.9 The abrasive used in this compound shall b

7、e powdered silica or a type of abrasive that is suitable for the purpose intended. ENGINEERING MATERIAL SPECIFICATION ESR-M5B194-B Page 2 of 3 Copyright 2002, Ford Global Technologies, Inc. 3.10 Must be capable of storage without any detrimental effect for an extended period of time. Supplier shall

8、furnish all necessary information on types of material required for packaging and on the storage life of the material in each of the product packages supplied. For any particular size container or package for the product, the supplier shall furnish information on safe storage practice and recommenda

9、tions as to maximum and minimum ambient temperatures and direct sun load conditions at which the product may be stored without adverse effects. If the package is considered unsafe for storage in an automotive vehicle, the package shall be labeled accordingly and the safe storage conditions specified

10、. 3.11 CHEMICAL & PHYSICAL PROPERTIES Specific chemical and physical properties are not specified herein, but an Engineering Quality Control Supplement will be issued to cover each approved material. The selected engineering approved source shall furnish appropriate chemical and physical properties

11、along with the production tolerance limits that apply to the material(s) upon which approval was given. The agreed upon values and limits will be issued to Quality Control by the affected product engineering office. These values will then be used by Quality Control for ongoing quality verifications.

12、 The Quality Control Supplement is an integral requirement of this specification. If more than one source supplies material to this specification, a Quality Control Supplement will be issued for each specific approved material. 3.12 LABELING 3.12.1 Provisions of this specification are applicable whe

13、n material is used according to labeling directions. Any precautions involved in the use of the material must be clearly stated on the product label. 3.12.2 The label(s) for the material(s) must comply to the Federal Hazardous Substances Act and all other provisions under the Consumer Product Safety

14、 Commission and all other applicable federal, state and local regulations. Supplier shall furnish the affected product engineering office with the label(s). 3.12.3 Suppler shall furnish certification that the composition of his product has been examined and that the label recommended is in complianc

15、e with the Federal Hazardous Substances Act and all other provisions under the Consumer Product Safety Commission. Completed Material Health and Safety Data Sheets and Hazardous Substances Data Sheets must be submitted by the supplier to the Ford Motor Company toxicologist. 3.12.4 If applicable, sup

16、plier shall furnish a copy of the laboratory report wherein the product was evaluated under the procedures required by the Federal Hazardous Substances Act. 3.12.5 Supplier must furnish detailed application instructions and specific usage information for container labels. This portion of the label i

17、nformation must be approved by the affected product engineering office. ENGINEERING MATERIAL SPECIFICATION ESR-M5B194-B Page 3 of 3 Copyright 2002, Ford Global Technologies, Inc. 3.12.6 If the label submitted by the supplier contains any advertising claims, suitable corroborative testing data must a

18、lso be furnished. Such claims and data are encouraged. 3.13 MARKING 3.13.1 Container and cartons must be marked with a code indicating source and compounding date of the material. Supplier must furnish this code to the affected product engineering office. Container marking may be waived if approved

19、in writing by the affected product engineering office. 3.13.2 The test report data furnished by the supplier showing compliance with this specification shall give the specific test methods followed and shall give specific answers to generalized requirements. 3.13.3 Generally accepted test methods (A

20、merican Society for Testing and Materials, Society of Automotive Engineers and Ford Laboratory Test Methods are preferred) and procedures should be followed where such methods are known, otherwise the methods of evaluation should be explained in detail. 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 4.1 Comparative performance data ratings utilizing the requirements outlined above, comparing the proposed material(s) to presently marketed Ford Motor Company products, are encouraged.