FORD ESF-M4D405-B-2011 POLYETHYLENE TEREPHTHALATE (PET) 45 % GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《聚乙烯对苯二甲酸酯(PET) 45%玻璃纤维增强模塑材料 与福特WSS-M99.pdf

《FORD ESF-M4D405-B-2011 POLYETHYLENE TEREPHTHALATE (PET) 45 % GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《聚乙烯对苯二甲酸酯(PET) 45%玻璃纤维增强模塑材料 与福特WSS-M99.pdf》由会员分享，可在线阅读，更多相关《FORD ESF-M4D405-B-2011 POLYETHYLENE TEREPHTHALATE (PET) 45 % GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《聚乙烯对苯二甲酸酯(PET) 45%玻璃纤维增强模塑材料 与福特WSS-M99.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Release No. Released Rev 03 2011 03 01 B - N-Status No replacement named A Pan, APA 2010 11 16 D/D2 N-STATUS No replacement named A. Pan, APA 1985 03 20 CF40RD888002-262 Released ESF-M4D405-D2 J.B. Huebner WP 3948-a Page 1 o

2、f 5 POLYETHYLENE TEREPHTHALATE (PET), NOT TO BE USED FOR NEW DESIGN ESF-M4D405-B 45 % GLASS FIBER REINFORCED MOLDING COMPOUND POLYETHYLENE TEREPHTHALATE (PET), NOT TO BE USED FOR NEW DESIGN ESF-M4D405-D 35 % GLASS FIBER/MICA REINFORCED MOLDING COMPOUND POLYETHYLENE TEREPHTHALATE (PET), NOT TO BE USE

3、D FOR NEW DESIGN ESF-M4D405-D2 45 % GLASS FIBER/MINERAL REINFORCED MOLDING COMPOUND 1. SCOPE The materials defined by these specifications are glass fiber and glass fiber/mineral reinforced thermoplastic polyester resins based on polyethylene terephthalate (PET). 2. APPLICATION These specifications

4、were released originally for materials used to mold frames for ignition control modules. 3. REQUIREMENTS 3.1 MOLDING COMPOUND B D D2 Nat. Pigmented 3.1.1 Melting Point, C, min 240 240 240 240 (ASTM D 789) 3.1.2 Reinforcement/Filler, +/- 2 % by weight (ASTM D 2584, 1 h at 666 C or TGA) . Glass Fiber

5、45 - - - . Glass Fiber/Mica - 35 - - . Glass Fiber/Mineral - - 45 45 +5/-2 3.1.3 Melt Flow Rate, g/10 minutes, max 4.0 - - - (ASTM D 1238, 280 +/- 0.2 C, 2.16 kg load) Dry sample for 1 h at 175 C in circulating air oven and maintain at this temperature until immediately before testing. Quickly charg

6、e indexer. Charging time not to exceed 1 min. ENGINEERING MATERIAL SPECIFICATION ESF-M4D405-B/D/D2 WP 3948-b Page 2 of 5 3.2 MOLDED TEST SPECIMEN 3.2.1 Preparation of Test Specimens All test specimens shall be injection molded in accordance with ASTM D 1897. The values of this specification are base

7、d on natural color, injection molded specimens unless otherwise specified on engineering drawing. 3.2.2 Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h

8、 prior to testing and tested under the same conditions unless otherwise specified. B D D2 Nat. Pigmented 3.2.3 Specific Gravity 1.68 1.56 1.66 1.66 (ASTM D 792) -1.72 min -1.70 -1.75 3.2.4 Tensile Strength, MPa, min 176 88 69 69 (ASTM D 638) 3.2.5 Flexural Modulus, GPa, min 12.1 7.6 6.2 6.2 (ASTM D

9、790) 3.2.6 Flexural Strength, MPa, min 248 134 124 124 (ASTM D 790) 3.2.7 Compressive Strength, 172 109 115 115 MPa, min (ASTM D 695), 3.2.8 Impact Strength, Izod, 101 48 43 43 J/m, min (ASTM D 256, notched) 3.2.9 Heat Deflection 215 193 210 200 Temperature, C, min (ASTM D 648. At 1.80 MPa) 3.2.10 D

10、ielectric Strength, kV/mm, min (ASTM D 149, short time) . Natural 18.5 20.1 15.8 15.8 . Black 13.8 14.4 10.8 10.8 ENGINEERING MATERIAL SPECIFICATION ESF-M4D405-B/D/D2 WP 3948-b Page 3 of 5 3.3 MOLDED PART 3.3.1 Color As specified on engineering drawing 3.3.2 Appearance Shall be uniform in density, t

11、exture and finish, free of visible porosity, warpage, heat scorch, checks, cracks, chipped edges and uneven surfaces. Shall also be free of other contamination. B D D2 Nat. Pigmented 3.3.3 Specific Gravity 1.68 1.56 1.66 1.66 (ASTM D 792) -1.72 -1.60 -1.70 -1.75 3.3.4 Reinforcement/Filler, 45 35 45

12、45 +5/-2 +/- 2 % by weight (1 h at 666 C or TGA) 3.4 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSIS Ford Motor Company, at its option, may conduct infrared and/or thermal analysis of material/parts supplied to this specification. The IR spectra and thermograms established for initial approval sh

13、all constitute the reference standard and shall be kept on file at the designated material laboratory. All samples shall produce IR spectra and thermograms that correspond to the reference standard when tested under the same conditions. 3.5 STATISTICAL PROCESS Suppliers must conform to the requireme

14、nts of Ford Quality System Standard Q-101. A mutually acceptable Control Plan as described therein is required for material/source approval. Appropriate statistical tools must be used to analyze process/product data so that variation in the final product is continuously reduced. 3.6 SUPPLIERS RESPON

15、SIBILITY All materials supplied to this specification must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any change in the properties, composition, construction, color, processing or labeling of the material originally approved under

16、 this specification, whether or not such changes affect the materials ability to meet the specification requirements, the Supplier shall notify Purchasing, Toxicology and the affected Materials Engineering activity of the proposed changes and obtain the written approval of the Materials Engineering

17、activity. Test data, test samples and a new code identification are to be submitted with the request. ENGINEERING MATERIAL SPECIFICATION ESF-M4D405-B/D/D2 WP 3948-b Page 4 of 5 Substance restrictions imposed by law, regulations or Ford, apply to the materials addressed by this document. The restrict

18、ions are defined in Engineering Materials Specification WSS-M99P9999-A1. 4. APPROVAL OF MATERIALS Materials defined by this specification must have prior approval by the responsible Materials Engineering activity. Suppliers desiring approval of their materials shall first obtain an expression of int

19、erest from the affected Purchasing, Design and Materials Engineering activity. Upon request, the Supplier shall submit to the affected Materials Engineering activity a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstra

20、ting full compliance with all the requirements of this specification (test results, not nominal values), the material designation and code number, and test specimens for Ford evaluation. Fords engineering approval of a material will be based on its performance to this specification and on an assessm

21、ent of suitability for intended processes and/or applications. Upon approval, the material will be added to the Engineering Material Approved Source List. 5 GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification.

22、 B D D2 Nat. Pigmented 5.1 FLAMMABILITY, mm/min 10 10 10 10 5.2 ELONGATION, % 2.1 2.2 2.0 2.0 (ASTM D 638) 5.3 IMPACT STRENGTH, Izod, J/m 1121 427 454 454 (ASTM D 256, unnotched) ENGINEERING MATERIAL SPECIFICATION ESF-M4D405-B/D/D2 WP 3948-b Page 5 of 5 5.4 RECYCLING CODE ESF-M4D405-B SAE PET-GF45 or PET-GF45PET-(GF+P)35PET-(GF+M)45 OPTIONAL