FORD ESF-M2L63-A-2003 NICKEL WIRE PTFE INSULATED TO BE USED WITH FORD WSS-M99P1111-A 《聚四氟乙烯（PTFE）绝缘的镍丝 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD ESF-M2L63-A-2003 NICKEL WIRE PTFE INSULATED TO BE USED WITH FORD WSS-M99P1111-A 《聚四氟乙烯（PTFE）绝缘的镍丝 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD ESF-M2L63-A-2003 NICKEL WIRE PTFE INSULATED TO BE USED WITH FORD WSS-M99P1111-A 《聚四氟乙烯（PTFE）绝缘的镍丝 与标准FORD WSS-M99P1111-A一起使用 》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2003 06 30 Revised Para 3.0 inserted; Para 3.1, 3.2, 3.3, 3.7, 4 deleted 1990 07 11 DE00E00107002060 Revised para 3.5, added 24 gage J. Huebner 1983 04 12 CF4N-RD887294-25 Released (Was XF-M1LX20) J. Huebner Printed copies are uncontrolled Cop

2、yright 2003, Ford Global Technologies, Inc. Page 1 of 2 NICKEL WIRE, PTFE INSULATED ESF-M2L63-A 1. SCOPE The material defined by this specification is a PTFE insulated nickel wire. The covering shall be 250 C classification. 2. APPLICATION This specification was released originally for material for

3、sensors. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.4 WIRE QUALITY The conductor shall consist of one solid nickel wire and shall be 97.0% nic

4、kel, minimum. 3.5 CONSTRUCTION 3.5.1 Conductor SAE Wire Size 24 30 Nominal Size, mm 0.508 0.255 Area of Conductor, mm2 0.202 0.05 3.5.2 Insulation Thickness (Nominal), mm 0.127 0.127 3.5.3 Finished Cable Diameter (Nominal), mm 0.760 0.521 Note: Use 30 gage wire for component fabrication unless other

5、wise specified on Engineering drawing. 3.6 INSULATION The insulating material shall be a good grade PTFE fluorocarbon which will pass the following test requirements: The material shall adhere closely to, but strip readily from the conductors, leaving them reasonably clean and in suitable condition

6、for soldering. Insulation thickness shall be in accordance with para 3.5.1 and shall be determined by measuring the diameter over the insulation, then removing the insulation and measuring the diameter of the conductor. Half of the difference of the two measurements shall be considered as the wall t

7、hickness. ENGINEERING MATERIAL SPECIFICATIONESF-M2L63-APrinted copies are uncontrolled Copyright 2003, Ford Global Technologies, Inc. Page 2 of 2 3.6.1 High Temperature Resistance Remove 25 mm of the insulation from each end of a 610 mm sample of the finished cable. The sample shall be suspended aro

8、und a cylindrical mandrel having a diameter of 114 mm. Each end of the conductor shall have suspended from it a weight of 0.45 kg. This condition shall be maintained for 168 h at 248 - 252 C in a circulating air oven. When cool, the weight shall be removed from the specimen and it shall be taken off

9、 the mandrel, bent in the reverse direction around a mandrel of 76 mm diameter at a rate not to exceed one complete turn/min and then be subjected to the dielectric test (para 3.6.2). 3.6.2 Dielectric Test A specimen of the cable 610 mm long shall be formed into a loop. Remove 25 mm of the insulatio

10、n from each end of the wire and the ends twisted together. The loop thus formed shall be immersed in water containing 5% salt by weight at room temperature, so that not more than 152 mm of each end of the specimen protrudes above the solution. After being immersed for 5 h and while still immersed, t

11、he specimen shall withstand the application of 1000 V (rms) at 60 Hz frequency between the conductor and the water for 1 minute without rupture of the insulation. 3.6.3 Oil Resistance A specimen 610 mm long shall be immersed to within 38 mm from the ends in a mixture of equal parts of kerosene and e

12、ngine lubricating oil at a temperature of 50 +/- 2 C for a period of 20 h. The sample shall then be removed from the solution, examined for deterioration of the insulating compound, and gaged for swelling. The outside diameter of the insulation of the cable shall not increase more than 15%. The samp

13、le shall then be bent around a mandrel 76 mm in diameter and checked for cracking; after the bend test the cable shall pass the dielectric breakdown test (para 3.6.2). 3.6.4 Cold Resistance A straight specimen shall be reduced to a temperature of - 40 C at a rate not to exceed 50 C/minute. After mai

14、ntaining this temperature for 3 h and while still at this low temperature, the cable shall be wrapped around a mandrel 76 mm in diameter for 180 at the uniform rate of one turn in 10 s. The insulation shall be removed for a distance of 25 mm from each end of the specimen and the specimen subjected t

15、o the dielectric test (para 3.6.2). 3.6.5 Flame Test A 610 mm specimen shall be suspended in a vertical position within a partial enclosure which allows a flow of sufficient air for complete combustion but is free from drafts. The tip of a 50 mm gas flame with an inner cone one-third its height shall then be applied to the end of the specimen for 15 s. After removal of the flame the specimen shall not continue to burn for more than 30 s. 3.6.6 Abrasion Resistance, min 152 mm of tape (SAE J 1128, Bracket A, 0.45 kg weight)