FORD ESE-M99C101-A-2009 OIL MINERAL - INITIAL FILL GASOLINE ADDITIVE TO BE USED WITH FORD WSS-M99P1111-A 《含汽油添加物的初始注入的矿物油 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD ESE-M99C101-A-2009 OIL MINERAL - INITIAL FILL GASOLINE ADDITIVE TO BE USED WITH FORD WSS-M99P1111-A 《含汽油添加物的初始注入的矿物油 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD ESE-M99C101-A-2009 OIL MINERAL - INITIAL FILL GASOLINE ADDITIVE TO BE USED WITH FORD WSS-M99P1111-A 《含汽油添加物的初始注入的矿物油 与标准FORD WSS-M99P1111-A一起使用 》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2009 11 17 N-STATUS No known use. No replacement named D. DiGregorio, NA 2004 02 24 Revised Para 3.0 inserted; paras 3.13 and 4 deleted 1981 10 01 Released CE3K-RD863100-E Supp. #29 Printed copies are uncontrolled Copyright 2009, Ford Global T

2、echnologies, LLC Page 1 of 2 OIL, MINERAL - INITIAL FILL ESE-M99C101-A GASOLINE ADDITIVE NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a base stock mineral oil. 2. APPLICATION This specification was released originally for material used as an initial fill fuel

3、additive to provide protection against spark plug soot fouling. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 VISCOSITY, at 40 C 90 - 98 mm2/s

4、(ASTM D 445) 3.2 VISCOSITY INDEX, min 95 (ASTM D 2270) 3.3 FLASH POINT, min 240 C (ASTM D 92) 3.4 POUR POINT, max -12 C (ASTM D 97) 3.5 API GRAVITY 29.0 - 31.0 (ASTM D 287) 3.6 CARBON CONTENT, max 0.10% (ASTM D 524) 3.7 COPPER STRIP CORROSION, max 1 (ASTM D 130, 3 h at 100 C) ENGINEERING MATERIAL SP

5、ECIFICATIONESE-M99C101-A Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 2 of 2 3.8 FERROUS CORROSION A (ASTM D 665) Rate corrosion as follows: Portion of Surface Rusted Rating None A (Pass) Less than 0.2% B+ (Borderline) 0.2 to 5% B+ (Fail) 5 to 25% B (Fail) 25 to

6、 50% C (Fail) 50 to 75% D (Fail) 75 to 100% E (Fail) 3.9 SULFUR CONTENT, max 0.33% (ASTM D 1266) 3.10 TOTAL ACID NUMBER, max 0.15 mg KOH/g (ASTM D 974) 3.11 The materials approved to this specification must be purchased from refinery and crude sources specified by the Material Activity of the Engine

7、 Product Engineering Office. 3.12 CERTIFICATION The supplier shall certify that the oil is a formula that has been tested and meets Ford Motor Company requirements as stated in this specification. This certification shall be by the suppliers Director of Research and Development or other authorized official and submitted to the Material Activity of the Engine Product Engineering office.