FORD ESE-M12G17-A-2006 FIBERGLASS HEAT INSULATING TUBE WOVEN TO BE USED WITH FORD WSS-M99P1111-A 《机织玻璃丝绝热管 与标准FORD WSS-M99P1111-A一起使用 使用标准WSS-M99P32-B》.pdf

《FORD ESE-M12G17-A-2006 FIBERGLASS HEAT INSULATING TUBE WOVEN TO BE USED WITH FORD WSS-M99P1111-A 《机织玻璃丝绝热管 与标准FORD WSS-M99P1111-A一起使用 使用标准WSS-M99P32-B》.pdf》由会员分享，可在线阅读，更多相关《FORD ESE-M12G17-A-2006 FIBERGLASS HEAT INSULATING TUBE WOVEN TO BE USED WITH FORD WSS-M99P1111-A 《机织玻璃丝绝热管 与标准FORD WSS-M99P1111-A一起使用 使用标准WSS-M99P32-B》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2006 05 02 N-STATUS Replaced by WSS-M99P32-B; Ins 3.0; Del 3.1, 3.2, 3.3, 3.8, 3.9 & 4 A. Reaume1990 09 04 NE01E1000047408 Revised and Updated. Added Standard Paragraphs 1963 10 04 Released E7 2825 Printed copies are uncontrolled Copyright 200

2、6, Ford Global Technologies, LLC Page 1 of 2 FIBERGLASS HEAT INSULATING TUBE, WOVEN ESE-M12G17-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a glass fiber yarn woven in a tubular form and treated with a suitable impregnant. 2. APPLICATION This specification w

3、as released originally for material used for insulating certain automotive parts when concerned with temperatures up to 370 C (i.e., heat tube between the exhaust manifold and carburetor for automatic chokes). 3. REQUIREMENTS Material specification requirements are to be used for initial qualificati

4、on of materials. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.4 COLOR Black or as specified on the engineering drawing. 3.5 CONSTRUCTION (ASTM D 578) ID, mm 4.8

5、 6.5 7.9 9.5 11.1 14.3 Warp Basic Yard ETG-25 ETG-25 ETG-25 ETG-25 ETG-25 ETG-25 Number of Plies 2 2 2 2 2 2 Total Ends, min 72 96 96 96 96 128 Filling Basic Meter, min ETG-3.5 ETG-2.7 ETG-1.4 ETG-2.7 ETG-1.4 ETG-1.4 Average of 10 Tests Number of Plies 1 1 1 1 1 1 Picks/100 mm 37 - 41 37 - 41 33 37

6、37 41 35 39 35 - 39 ENGINEERING MATERIAL SPECIFICATIONESE-M12G17-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 2 of 2 3.6 TREATMENT The 4.8 mm, 6.5 mm, 7.9 mm, 9.5 mm, 11.1 mm ID tubing shall be saturated with a suitable impregnant to facilitate the subsequent

7、flame treatment. The tubing shall be free from beads or seams or any obstructions which will interfere with assembly. The treatment must be dry and nontacky. After impregnation, the tube shall be singed to remove all loose external fiber ends. All material shall have the ends cut with a circular kni

8、fe or other appropriate means to prevent fraying. Cut ends are to be treated with a heat resistant plastic to prevent fraying. 3.7 PERFORMANCE AND TESTING Shall withstand a temperature of 370 C for 24 h without apparent disintegration. Shall have a sufficient rigidity to facilitate production, to retain purpose, and to form an assembly without requiring clamp or other holding devices. Shall have sufficient flexibility to permit bending 90 C about a 25 mm mandrel at 23 +/- 2 C and then return to a shape or form which is suitable for “slip-on“ assembly.