FORD ESB-M99J291-A5-2012 TAPE WITH CLEARCOAT URETHANE PRESSURE SENSITIVE CHIP RESISTANT EXTERIOR 0 43 mm NOMINAL THICKNESS 0 13 mm ADHESIVE THICKNESS TO BE USED WITH FORD WSS-M99P.pdf
《FORD ESB-M99J291-A5-2012 TAPE WITH CLEARCOAT URETHANE PRESSURE SENSITIVE CHIP RESISTANT EXTERIOR 0 43 mm NOMINAL THICKNESS 0 13 mm ADHESIVE THICKNESS TO BE USED WITH FORD WSS-M99P.pdf》由会员分享,可在线阅读,更多相关《FORD ESB-M99J291-A5-2012 TAPE WITH CLEARCOAT URETHANE PRESSURE SENSITIVE CHIP RESISTANT EXTERIOR 0 43 mm NOMINAL THICKNESS 0 13 mm ADHESIVE THICKNESS TO BE USED WITH FORD WSS-M99P.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 02 2012 02 16 N Status No replacements named N. Benipal, NA 2005 08 11 Revised Inserted 3.0; deleted 3.1, 3.2, 3.3, 3.9 and 4 1993 02 09 Released NB00E10268592000 K. P. Tremonti Printed copies are uncontrolled Copyright 2012, Ford Global
2、Technologies, LLC Page 1 of 4 TAPE WITH CLEARCOAT, URETHANE, PRESSURE SENSITIVE, ESB-M99J291-A5 CHIP RESISTANT, EXTERIOR, 0.43 mm NOMINAL THICKNESS, 0.13 mm ADHESIVE THICKNESS NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a clear, paper backed, abrasion resista
3、nt urethane film with a water clear pressure sensitive adhesive. A clearcoat is applied over the urethane film to prevent film yellowing. 2. APPLICATION This specification was released originally for material used to provide localized stone chip protection on painted lower bodyside areas. This tape
4、is suitable for application to visible exterior areas over painted surfaces with or without PVC type stoneguard coatings. It has a high tack, 0.13 mm thickness adhesive. A dry surface is recommended for tape application. Tape dimensions and premask (with or without) are specified on the engineering
5、drawings. 3. REQUIREMENTS All testing to be done on finished production parts (i.e., film to be used to design intent and application on production substrate/paint). 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Require
6、ments For Production Materials (WSS-M99P1111-A). 3.4 CONSTRUCTION 3.4.1 Thickness (ASTM D 1000) 3.4.1.1 Clearcoat, micrometer 10 - 18 3.4.1.2 Film, mm 0.29 - 0.31 3.4.1.3 Adhesive, mm 0.12 - 0.14 3.4.2 Width and Length As specified on engineering drawing 3.4.3 Premask As specified on engineering dra
7、wing ENGINEERING MATERIAL SPECIFICATION ESB-M99J291-A5 Printed copies are uncontrolled Copyright 2012, Ford Global Technologies, LLC Page 2 of 4 3.5 FILM PROPERTIES 3.5.1 Appearance The film and adhesive shall be water clear and colorless. Color difference from a white painted panel shall be 2.0 or
8、less Delta E on a CMC 2:1 colorimeter scale. 3.5.2 Gloss 75 +/- 10 (FLTM BI 110-01, using a 20 glossmeter) 3.5.3 Tensile Strength, min 10 MPa (ASTM D 882, Method A, 25 x 150 mm sample, 25 mm distance between bench marks, jaw spaced at start 100 mm, pull rate 300 mm/minute, as measured at breaking po
9、int) 3.5.3.1 Elongation, min 250% 3.5.4 Tear Strength, min 0.9 kg (ASTM D 624, Die C) 3.6 PERFORMANCE PROPERTIES Appearance After Exposure: In addition to any other requirements specified, the film after exposure per para 3.6.1 through 3.6.6 shall show no evidence of cracking, blistering, lifting, o
10、r color change in excess of 3.5 Delta E on a CMC 2:1 colorimeter scale compare with an exposed white painted panel and no gloss change greater than 15%. Sample Preparation: . Prepare painted 100 x 300 mm panels per para 5.1.1, 5.1.2, and 5.1.3. . Apply a minimum of 3 - 25 x 100 mm strips of tape to
11、each panel per ASTM D 1000, Method A. Surface shall be clean and dry prior to tape application. 3.6.1 180 Mean Peel Adhesion Value, min 600 N/m (ASTM D 1000, Method A, evaluate plot according to ISO 6133, Figure 1) Initial Adhesion: 3.6.1.1 20 minutes at 23 +/- 2 C Exposure: 3.6.1.2 72 h at 70 +/- 1
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDESBM99J291A52012TAPEWITHCLEARCOATURETHANEPRESSURESENSITIVECHIPRESISTANTEXTERIOR043MMNOMINALTHICKNESS013MMADHESIVETHICKNESSTOBEUSEDWITHFORDWSSM99PPDF
链接地址:http://www.mydoc123.com/p-745774.html