FORD ESB-M99J274-B-2012 PAINT HOT STAMP TRANSFER EXTERIOR PLASTIC TO BE USED WITH FORD WSS-M99P1111-A 《热模锻转移外部塑料涂料 与福特WSS-M99P1111-A 一起使用》.pdf
《FORD ESB-M99J274-B-2012 PAINT HOT STAMP TRANSFER EXTERIOR PLASTIC TO BE USED WITH FORD WSS-M99P1111-A 《热模锻转移外部塑料涂料 与福特WSS-M99P1111-A 一起使用》.pdf》由会员分享,可在线阅读,更多相关《FORD ESB-M99J274-B-2012 PAINT HOT STAMP TRANSFER EXTERIOR PLASTIC TO BE USED WITH FORD WSS-M99P1111-A 《热模锻转移外部塑料涂料 与福特WSS-M99P1111-A 一起使用》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 03 2012 02 16 N Status No replacements named N. Benipal, NA 2005 08 10 Revised Inserted 3.0; deleted 3.1, 3.5 and 4 1979 04 20 Released AJ1-6000-223 Controlled document at www.MATS Copyright 2012, Ford Global Technologies, LLC Page 1 of 4
2、 PAINT, HOT STAMP TRANSFER, EXTERIOR PLASTIC ESB-M99J274-B PAINT, HOT STAMP TRANSFER, FIRST SURFACE EXTERIOR ESB-M99J275-B ACRYLIC PLASTIC NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by these specifications is a paint film applied on a carrier film and subsequently transferred to pla
3、stic parts by a hot stamp process. 2. APPLICATION These specifications were released originally for material used as a first surface decorative finish on exterior plastic parts. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to t
4、he Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 FILM PROPERTIES 3.2.1 Color (FLTM BI 109-01) Shall match master panel approved by Styling. 3.2.2 Gloss Shall conform to requirements shown on engineering drawings, material specifications, or letter suffix attached to S
5、tyling color number. 3.2.3 Initial Hardness Shall be sufficiently cured at time of packing to withstand normal handling and shipping without damage. 3.2.4 Film Thickness, min 0.0004 in (10 m) (FLTM BI 117-01) 3.2.5 Hiding Solid colors shall provide complete visual hiding at 0.0004 in (10 m) film thi
6、ckness. Translucent colors shall be equal to approved color master. ENGINEERING MATERIAL SPECIFICATION ESB-M99J274-B ESB-M99J275-B Copyright 2012, Ford Global Technologies, LLC Page 2 of 4 3.3 PREPARATION OF TEST SPECIMENS 3.3.1 When it is not feasible to test the actual part because of its size, la
7、boratory panels may be substituted. Test panels shall be processed concurrently with parts and shall be representative of parts with respect to substrate, color coat, color coat thickness, and bake (if necessary) and all other operations. 3.3.2 Aging Age the panels or parts 16 h at 60 +/- 3 C or 72
8、h at 23 +/- 2 C before testing unless otherwise noted. 3.3.3 Material Application 3.3.3.1 ESB-M99J274-B Painted Plastic 3.3.3.2 ESB-M99J275-B Unpainted Acrylic Plastic 3.4 RESISTANCE PROPERTIES 3.4.1 Abrasion Resistance, min 80 cycles min at (FLTM BN 108-02, CS-10 the specified wheels, 500 g load) f
9、ilm thickness, 0.0004 in (10 m) 3.4.2 Water Resistance, min 96 h Test Method: Immerse the panels in distilled or deionized water maintained at 32 +/- 1 C per FLTM BI 104-01. Remove parts from the water and immediately scribe an “X“ through the material to the substrate. Dry the scribed area with a p
10、aper towel, cloth or air pressure and immediately apply, with firm thumb pressure, a minimum of 2 in2 (13 cm2) of ESF-M3G48-A tape. Remove the tape by pulling one end at a 90 angle at a moderate speed. The following conditions shall be basis for rejection: . Removal of paint beyond 1/16 in (1.6 mm)
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDESBM99J274B2012PAINTHOTSTAMPTRANSFEREXTERIORPLASTICTOBEUSEDWITHFORDWSSM99P1111A 热模锻 转移 外部 塑料 涂料 福特
链接地址:http://www.mydoc123.com/p-745768.html