FORD ESB-M99G127-B1-2000 SOUND BARRIER - CALENDERED PVC RUBBER - MOLDABLE (Shown on ESB-M99G127-A1)《可模压经压光处理的聚氯乙烯（PVC） 橡胶声障 列于标准ESB-M99G127-A1上》.pdf

《FORD ESB-M99G127-B1-2000 SOUND BARRIER - CALENDERED PVC RUBBER - MOLDABLE (Shown on ESB-M99G127-A1)《可模压经压光处理的聚氯乙烯（PVC） 橡胶声障 列于标准ESB-M99G127-A1上》.pdf》由会员分享，可在线阅读，更多相关《FORD ESB-M99G127-B1-2000 SOUND BARRIER - CALENDERED PVC RUBBER - MOLDABLE (Shown on ESB-M99G127-A1)《可模压经压光处理的聚氯乙烯（PVC） 橡胶声障 列于标准ESB-M99G127-A1上》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number 2000 O9 29 1978 1 O 13 SOUND BARRIER - CALENDERED PVC/RUBBER - MOLDABLE Revised Updated & renumbered A. Cockman CAHI -RD572066-129 Metricated, renumbered & retvped SOUND BARRIER - CALENDERED PVC - MOLDABLE V ESB-M99G127-A1 ESB-M99

2、G127-B1 V ESB-M99G127-A2 ESB-M99G127-B2 1. SCOPE The materials defined by this specification are thermally moldable calendered PVC compounds that may be used as sound barriers are usually bonded to batt type insulation material. 2. APPLICATION This specification was released originally for materials

3、 used as molded dash insulators, bonded to a reclaimed fiber pad. They were specifically formulated with strength and stiffness properties which would allow direct support of wiring harnesses and other attachment devices without requiring brackets. V ESB-M99GI 27-Al and ESB-M99GI 27-BI were original

4、ly designated V ESB-M99GI 27-A and ESB- M99G127-B, and whenever V ESB-M99GI 27-A and ESB-M99GI 27-B are indicated on engineering drawings, patterns, specifications, etc., the V ESB-M99GI 27-Al and ESB-M99GI 27-BI specifications will be understood to apply. 3. REQUIREMENTS Material specification requ

5、irements are to be used for initial qualification of materials. 3.1 QUALITY SYSTEM REQUIREMENTS Material suppliers and part producers must conform to the Companys Quality System Requirements. 3.2 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material conditioned in a

6、 controlled atmosphere of 23 +/- 2 OC and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. 3.3 APPEARANCE The barrier material as received, bonded to a reclaimed fiber pad underlay, shall be uniformly smooth, withou

7、t blisters or deep recesses. There shall be no breaks in the vinyl film that would permit any exposure of the underlay material. I Date I Action I Revisions I I 197711 22 I AHI-710 I Released ESB-M99G127-Al/Bl I Copyright 0 2000, Ford Global Technologies, Inc ENGINEERING MATERIAL SPECIFICATION V ESB

8、-M99G127-A1/A2 ESB-M99G127-Bl/B2 3.4 3.5 3.6 3.7 3.8 3.9 3.1 O COLOR Black SPECIFIC GRAVITY (ASTM D 792) TENSILE STRENGTH, psi (MPa), min (ASTM D 412, Die “A“) ELONGATION %, min (ASTM D 41 2, Die “A“) TEAR STRENGTH, Ibhn (N/mm), min (ASTM D 624, Die “C“) HARDNESS (ASTM D 2240, Type A, 15 s) ACOUSTIC

9、AL PROPERTIES V ESB-M99G127-Al/Bl V ESB-M99GI 27-A2/B2 1.9 +/- 0.1 1.5 +/- 0.1 1 O00 (6.9) 675 (4.7) 1 O0 200 (35) 85 +/- 10 65 1 O0 (1 7.5) 85 +/- 10 Shall be conducted for initial source approval and as required by the affected product engineering office. 3.10.1 Sound Transmission Loss, min (FLTM

10、BV 3-6, Method A) Frequency - Hz Transmission Loss - dB* 125 250 500 1 O00 2000 4000 13 14 8 11 29 25 *Values based on a material weight of 8 oz/fi2 (2.4 kg/m2) 3.10.2 Vibrational Damping, min (FLTM BV 3-4) 16 14 % 2 IC 0 12 E CS .- o 2 45 40 N E 35 1 E o o . 30 2 25 2 20 DECAY RATE - dB/s Page 2 of

11、 4 Copyright 0 2000, Ford Global Technologies, Inc ENGINEERING MATERIAL SPECIFICATION V ESB-M99G127-A1/A2 ESB-M99G127-Bl/B2 3.1 1 3.1 2 3.1 3 3.1 4 FOGGING, min (FLTM BO 16-2) 70 Exudation resulting in running liquid, heavy beads and/or droplets or a continuous film deposit on the surface of the pla

12、te are not desired and shall be reported along with numerical results but shall not be cause for rejection. COLD FLEXIBILITY (FLTM BN 2-1, except no heat cycles, - 23 +/- 2 OC, 1 in (25 mm) mandrel) ASSEMBLY REQUIREMENTS 3.1 3.1 Heat Resistance (2 h at 82 +/- 2 OC) 3.13.2 Ply Adhesion, min (ASTM D 4

13、13, machine method, 12 in (3.5 mm)/min jaw speed) No cracks The barrier material shall not flow or delaminate from underlay material or shall the material become tacky enough to transfer any color to white paper toweling. 1 .O Ib/in (1 75 N/m) width When used in a composite with a fiber or foam pad,

14、 the barrier material must be bonded to the pad at all points. When the barrier material is peeled from the pad, the adhesion shall produce tearing of the pad, leaving fiber or foam particles adhering to the barrier material across the entire surface. V ESB-M99G127-A1, A2 FLAMMABILITY REQUIREMENT V

15、3.14.1 In order to comply with Federal Motor Vehicle Safety Standard No. 302, the materials, portions of components, and composites shall not burn, or transmit a flame across its surface, at a rate of more than 4 in (101 mm) per min. To demonstrate compliance, the sample size and method of testing s

16、hall be in accordance with FLTM BN 24-2. 3.1 4.2 Performance - Environmental Aging All materials, portions of components, and composites defined by this specification that have not been treated, modified or reformulated and exceed a max burn rate of 3.0 in (76 mm) per min as specified by the Flammab

17、ility Lot Sampling Plan of FLTM BN 24-2, must be evaluated for permanency of the materials flame retardant properties per ESB-M25P3-A according to the accelerated environmental aging requirements applicable to the basic material category of this particular specification. Any material, portions of co

18、mponents, and composites defined by this specification that have been treated, modified or reformulated to conform to Flammability Lot Sampling Plan of FLTM BN 24-2, regardless of max burn rate, must be evaluated for both permanency of materials flame retardant properties and changes in mechanical,

19、chemical and physical properties per ESB-M25P3-A applicable to the basic materials category of this particular specification. Page 3 of 4 Copyright 0 2000, Ford Global Technologies, Inc ENGINEERING MATERIAL SPECIFICATION V ESB-M99G127-A1/A2 ESB-M99G127-Bl/B2 3.1 4.3 Flammability Test Program Materia

20、ls, portions of components, and composites governed by this specification must also comply with the requirements of V ES-D3AB-I 1 O1 4-AA. 3.1 5 ESB-M99G127-Bl/B2 FLAMMABILITY, max (FLTM BN 24-2, without the lot sampling plan) 4 in (1 O1 mm)/min In addition, the test specimen shall not exhibit any f

21、lashing or sudden flaming on either surface in excess of the above maximum value. 3.16 SUPPLIERS RESPONSIBILITY All materials supplied to this specification must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the materi

22、al originally approved under this specification, whether or not such changes affect the materials ability to meet the specification requirements, the Supplier shall notify the affected Purchasing, and Materials Engineering activities (with reasons) of the proposed changes. Upon notification of the C

23、ompany, further instructions will be provided. Note: Suppliers should be prepared to provide test data and samples demonstrating compliance to this specification, if requested. Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The

24、 restrictions are identified in Restricted Substance Management Standard WSS-M99P9999-A1. 4. APPROVAL OF MATERIALS Materials defined by this specification for direct supply to the Company must have prior approval. Certain materials subcontracted by part suppliers may also require prior approval. The

25、se include materials critical to the Companys business for regulatory, safety, environmental or compatibility requirements or contractual agreements. Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Materials Engineering activity.

26、 Upon request, the Supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of this specification. Page 4 of 4 Copyright 0 2000, Ford Global Technologies, Inc