FORD ESB-M6J125-A-2012 PRIMER SEALER ACRYLONITRILE BUTADIENE STYRENE (ABS) SURFACES TO BE USED WITH FORD WSS-M99P1111-A .pdf
《FORD ESB-M6J125-A-2012 PRIMER SEALER ACRYLONITRILE BUTADIENE STYRENE (ABS) SURFACES TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享,可在线阅读,更多相关《FORD ESB-M6J125-A-2012 PRIMER SEALER ACRYLONITRILE BUTADIENE STYRENE (ABS) SURFACES TO BE USED WITH FORD WSS-M99P1111-A .pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 03 2012 05 14 N Status No usage or replacement N. Benipal, NA 2008 04 22 Revised Inserted 3.0; Deleted 3.6 & 4 1970 06 15 Released AZ1-1375 Controlled document at www.MATS Copyright 2012, Ford Global Technologies, LLC Page 1 of 3 PRIMER S
2、EALER, ACRYLONITRILE BUTADIENE STYRENE (ABS) ESB-M6J125-A SURFACES NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a primer sealer with good adhesion to ABS plastic surfaces, which will not permit transmission of lacquer solvents and thus prevent crazing of the A
3、BS surface. 2. APPLICATION This specification was released originally for material used as a primer sealer on ABS exterior parts where acrylic service repair lacquer is used as the color coat. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers mu
4、st conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 PHYSICAL PROPERTIES 3.1.1 Non-Volatile Solids (FLTM BI 102-01) To be established by the vendor on the initial approved production batch. Tolerance shall be +/- 0.5%. 3.1.2 Viscosity (FLTM BI 111-02) Shall
5、 be established by the vendor on the initial approved production batch. Tolerance shall be +/- 5 s. 3.1.3 Stability (FLTM BI 102-03) The material shall not liver or jell upon standing and must be free from settling which is not dispersed by normal agitation. The viscosity of the material shall not i
6、ncrease more than 10 s. 3.1.4 Hiding (FLTM BI 111-01) Solid colors shall provide complete opacity at 0.001 in (25 m) film thickness. Translucent colors shall be equal to approved samples. ENGINEERING MATERIAL SPECIFICATION ESB-M6J125-A Copyright 2012, Ford Global Technologies, LLC Page 2 of 3 3.2 PR
7、EPARATION OF TEST PANELS ABS panels of any convenient size may be used. Solvent wipe to remove soil and mold release compound. Reduce ESB-M6J125-A to 15 - 20 s #4 Ford Cup with the reducing thinner recommended by the supplier. Spray 0.0005 - 0.00075 in (13 - 19 m) (dry film thickness) and force dry
8、45 min at 66 C. Spray ESB-M4J54 Black applying 4 coats, with a 1 min flash between coats, to obtain a dry film thickness of 0.0012 - 0.0018 in (30 - 45 m). Force dry 45 min at 66 C. Age all panels 96 h before testing. 3.3 APPEARANCE 3.3.1 Color Gray (No darker than master color panel) 3.3.2 Holdout
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDESBM6J125A2012PRIMERSEALERACRYLONITRILEBUTADIENESTYRENEABSSURFACESTOBEUSEDWITHFORDWSSM99P1111APDF

链接地址:http://www.mydoc123.com/p-745675.html