FORD ESB-M11P33-A-2013 ADHESION REQUIREMENT ADHESIVE FOR BONDING PLASTIC U-CLIPS TO GLASS IN DOOR WINDOW ASSEMBLY TO BE USED WITH FORD WSS-M99P1111-A .pdf
《FORD ESB-M11P33-A-2013 ADHESION REQUIREMENT ADHESIVE FOR BONDING PLASTIC U-CLIPS TO GLASS IN DOOR WINDOW ASSEMBLY TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享,可在线阅读,更多相关《FORD ESB-M11P33-A-2013 ADHESION REQUIREMENT ADHESIVE FOR BONDING PLASTIC U-CLIPS TO GLASS IN DOOR WINDOW ASSEMBLY TO BE USED WITH FORD WSS-M99P1111-A .pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Release No. Release/Revision 2013 12 12 N Status No replacement named. L. Sinclair, NA 1985 10 23 CSQ1-DC534172 Controlled document at www.MATS Page 1 of 4 ADHESION REQUIREMENT, ADHESIVE FOR BONDING ESB-M11P33-A PLASTIC U-CL
2、IPS TO GLASS IN DOOR WINDOW ASSEMBLY NOT TO BE USED FOR NEW DESIGN 1. SCOPE This specification defines the adhesion requirements for an adhesive or an adhesive system for bonding plastic U-clips to glass in door window assembly. 2. APPLICATION This specification was released originally for adhesive
3、used to bond ESB-M4D357 polyacetal to ESB-M28G9 glass. Compliance with this performance specification does not guarantee the adhesive will function for all potential applications on a vehicle. The specific assembly should be evaluated to design engineering performance requirements. Materials meeting
4、 this performance specification are specified on the Corporate Approved Source List. 3. REQUIREMENTS 3.1 CONDITIONING All test values indicated herein are based on materials conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for 24 h prior to testing and tested und
5、er the same conditions unless otherwise stated herein. 3.2 TENSILE ADHESION Average load specified or substrate breakage Subject bonded test assemblies to the following exposures: . Normal (Condition for 30 min at specified temperature prior to test) 3.2.1 Test at 23 +/- 2 C 1100 N 3.2.2 Test at 88
6、+/- 1 C 450 N 3.2.3 Test at - 29 +/- 1 C 1400 N ENGINEERING MATERIAL SPECIFICATION ESB-M11P33-A Page 2 of 4 . Environmental Aged 3.2.4 1000 h heat at 88 +/- 1 C 1100 N 3.2.5 1000 h humidity at 38 +/- 2 C and 900 N 95 - 100 % R.H. 3.2.6 1000 h water immersion 900 N (FLTM BI 4-1) 3.2.7 240 h salt spra
7、y 1100 N (ASTM B 117) 3.2.8 10 thermal cycles: 1100 N 4 h at 88 +/- 1 C 4 h humidity (38 +/- 2 C and 95 - 100 % R.H), 16 h at - 29 +/- 2 C 3.2.9 240 h ultraviolet light 1100 N (FLTM BV 7-2) 3.2.10 240 h WSB-M1C208 grease immersion 1100 N at 40 +/- 2 C 3.2.11 1 h heat at 120 +/- 1 C 1100 N Test Metho
8、d: . Prepare a minimum of 3 test assemblies per test condition as illustrated in Figure 1. . Test substrates are identified in para 5.1. . Condition test assemblies for 96 h minimum at 23 +/- 2 C prior to environmental exposure. . Allow test assemblies to condition 24 h minimum at 23 +/- 2 C after e
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDESBM11P33A2013ADHESIONREQUIREMENTADHESIVEFORBONDINGPLASTICUCLIPSTOGLASSINDOORWINDOWASSEMBLYTOBEUSEDWITHFORDWSSM99P1111APDF

链接地址:http://www.mydoc123.com/p-745036.html