ETSI TS 152 021-2018 Digital cellular telecommunications system (Phase 2+) (GSM) Network Management (NM) procedures and messages on the A-bis interface (V15 0 0 3GPP TS 52 021 vers.pdf

《ETSI TS 152 021-2018 Digital cellular telecommunications system (Phase 2+) (GSM) Network Management (NM) procedures and messages on the A-bis interface (V15 0 0 3GPP TS 52 021 vers.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 152 021-2018 Digital cellular telecommunications system (Phase 2+) (GSM) Network Management (NM) procedures and messages on the A-bis interface (V15 0 0 3GPP TS 52 021 vers.pdf（66页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 152 021 V15.0.0 (2018-07) Digital cellular telecommunications system (Phase 2+) (GSM); Network Management (NM) procedures and messages on the A-bis interface (3GPP TS 52.021 version 15.0.0 Release 15) TECHNICAL SPECIFICATION GLOBAL SYSTEM FOR MOBILE COMMUNICATIONSRETSI ETSI TS 152 021 V15.0

2、.0 (2018-07)13GPP TS 52.021 version 15.0.0 Release 15Reference RTS/TSGR-0652021vf00 Keywords GSM ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Pr

3、fecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not

4、be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secreta

5、riat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, pl

6、ease send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written pe

7、rmission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2018. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI regis

8、tered for the benefit of its Members. 3GPPTM and LTETMare trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSMand the GSM logo are trademarks registered and owned by the GSM Association. ETS

9、I ETSI TS 152 021 V15.0.0 (2018-07)23GPP TS 52.021 version 15.0.0 Release 15Intellectual Property Rights Essential patents IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly availab

10、le for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server

11、(https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,

12、essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reprodu

13、ce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership P

14、roject (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities

15、 can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal for

16、ms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 152 021 V15.0.0 (2018-07)33GPP TS 52.021 version 15.0.0 Release 15Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Forew

17、ord . 7g3Introduction 7g31 Scope 8g32 References 8g33 Definitions and abbreviations . 9g33.1 Definitions 9g33.2 Abbreviations . 9g34 Functional Split between BSC and BTS 9g35 Information Model . 10g35.1 Managed Objects 10g35.2 Addressing of Objects 13g35.3 State Management of Objects . 13g35.3.1 Adm

18、inistrative State . 13g35.3.2 Operational State and Availability Status . 14g36 Elementary Procedures . 15g36.1 Definition of the Procedures . 16g36.2 SW Download Management Procedures 16g36.2.1 Load Data Initiate . 16g36.2.2 Load Data Segment . 16g36.2.3 Load Data Abort . 17g36.2.4 Load Data End 17

19、g36.2.5 SW Activate Request 17g36.2.6 Activate SW 18g36.2.7 SW Activated Report 18g36.3 A-bis Interface Management Procedures . 18g36.3.1 Establish TEI 18g36.3.2 Connect Terrestrial Signalling 18g36.3.3 Disconnect Terrestrial Signalling . 19g36.3.4 Connect Terrestrial Traffic . 19g36.3.5 Disconnect

20、Terrestrial Traffic . 19g36.4 Transmission Management Procedures 19g36.4.1 Connect Multi-drop Link 19g36.4.2 Disconnect Multi-drop Link . 20g36.5 Air Interface Management Procedures . 20g36.5.1 Set BTS Attributes 20g36.5.2 Set Radio Carrier Attributes 20g36.5.3 Set Channel Attributes 20g36.6 Test Ma

21、nagement Procedures . 21g36.6.1 Perform Test . 21g36.6.2 Test Report 21g36.6.3 Send Test Report . 21g36.6.4 Stop Test . 22g36.7 State Management and Event Report Procedures . 22g36.7.1 State Changed Event Report . 22g36.7.2 Failure Event Report . 22g36.7.3 Stop Sending Event Reports . 23g36.7.4 Rest

22、art Sending Event Reports . 23g36.7.5 Change Administrative State 23g36.7.6 Change Administrative State Request. 23g3ETSI ETSI TS 152 021 V15.0.0 (2018-07)43GPP TS 52.021 version 15.0.0 Release 156.7.7 Report Outstanding Alarms 23g36.8 Equipment Management Procedures 24g36.8.1 Change-over 24g36.8.2

23、Opstart 24g36.8.3 Reinitialize 24g36.8.4 Set Site Outputs 25g36.9 Measurement Management Procedures 25g36.9.1 Measurement Result Request 25g36.9.2 Measurement Result Response . 25g36.9.3 Stop Measurement 25g36.9.4 Start Measurement 26g36.10 Miscellaneous Procedures 26g36.10.1 Get Attributes 26g36.10

24、.2 Set Alarm Threshold . 26g36.10.3 Get Attributes Response . 26g37 Structured Procedures. 26g38 Message Details 26g38.1 Message Categories 27g38.1.1 Formatted O 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for

25、all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. Introduction (Background) The use and general aspects of the A-bis interface are given in specification 3GPP TS 48.05

26、1. The split of telecommunications functions and management procedures between BSC and BTS are defined in specification 3GPP TS 48.052. Specification 3GPP TS 48.056 defines Layer 2 of the signalling messages. The general aspects of NM are defined in specification GSM 12.00. Qx interface and protocol

27、 stack are defined in specification GSM 12.01. GSM 12.06 provides the functional requirements supported by the present document. The NM procedures and messages to support these operations over the A-bis interface are specified here. Specification GSM 12.20 provides the information model as seen on t

28、he OMC-BSC interface. Interworking between this model and the NM messages and procedures provided here is specified in GSM 12.22. ETSI ETSI TS 152 021 V15.0.0 (2018-07)83GPP TS 52.021 version 15.0.0 Release 151 Scope The present document addresses the network management messages and procedures acros

29、s the A-bis interface, which is defined as Qx in GSM. The information model included here defines the objects and how they are addressed for purposes of operations and maintenance activities. There is a requirement for the A-bis interface to be open to allow interoperation between BTSs of different

30、manufacturers working to the same BSC. The present document addresses this requirement from O Core network protocols; Stage 3“. 4 3GPP TS 45.002: “Multiplexing and Multiple Access on the Radio Path“. 5 3GPP TS 45.005: “Radio transmission and reception“. 6 3GPP TS 45.008: “Radio subsystem link contro

31、l“. 7 3GPP TS 48.051: “Base Station Controller - Base Tranceiver Station (BSC-BTS) Interface General Aspects“. 8 3GPP TS 48.052: “Base Station Controller - Base Tranceiver Station (BSC-BTS) Interface - Interface Principles“. 9 3GPP TS 48.056: “BSC-BTS Layer 2 Specification“. 10 3GPP TS 48.058: “Base

32、 Station Controler - Base Transceiver Station (BCS-BTS) Interface Layer 3 Specification“. 11 GSM 12.00 (GSM Phase 2): “Objectives and structure of Network Management (NM)“. 12 GSM 12.01 (GSM Phase 2): “Common aspects of GSM Network Management (NM)“. 13 GSM 12.06 (GSM Phase 2): “GSM Network Configura

33、tion Management and Administration“. 14 GSM 12.20 (GSM Phase 2): “Base Station System (BSS) Management Information“. 15 GSM 12.22 (GSM Phase 2): “Interworking of GSM Network Management (NM) procedures and messages at the Base Station Controller (BSC)“. ETSI ETSI TS 152 021 V15.0.0 (2018-07)93GPP TS

34、52.021 version 15.0.0 Release 1516 ITU-T Recommendation X.731: “Information technology - Open Systems Interconnection - Systems Management: State management function“. 3 Definitions and abbreviations 3.1 Definitions Definitions of terms used within the present document may be found mostly in clause5

35、 in text context. 3.2 Abbreviations For the purpose of the present document, the following abbreviations apply: ASN.1 (CCITT) Abstract Syntax Notation One BSC Base Station Controller BSS Base Station System BTS Base Transceiver Station cont. continued HW HardwareLSB Least Significant Byte man. dep.

36、manufacturer dependent (with upper and lower case adjusted as appropriate) MMI Man-machine Interface MSB Most Significant Byte MSC Mobile-services Switching Centre NE Network Element NM Network Management O req = request; X = Function exists; ex = execution - = Function non-exists; rpt = report 5 In

37、formation Model 5.1 Managed Objects The BCF mentioned in 3GPP TS 48.052 and 3GPP TS 48.056 is the agent at the BTS end of the A-bis O - operability: whether or not the resource is physically installed and working. The present document defines the following three state management attributes to repres

38、ent the management state of a managed object: - administrative state; - operational state; - availability status (this elaborates the operational state). 5.3.1 Administrative State Administrative states of the managed objects can be controlled only by the BSC. In fact, the control of resource usage

39、comes from the MSC). ETSI ETSI TS 152 021 V15.0.0 (2018-07)143GPP TS 52.021 version 15.0.0 Release 15Setting the administrative state of a Channel to locked means that it has to discontinue all transmission and reception of information on Air interface and all telecommunication (traffic and signalli

40、ng) information transmission on A-bis interface. Setting the administrative state of a Radio Carrier to locked means that it has to discontinue all RF emission on Air interface for the frequencies it is responsible. Setting the administrative state of a Baseband Transceiver to locked means that it h

41、as to discontinue all telecommunication tramissions and the Channels which are affected should indicate that they are Disabled or Degraded. Setting the administrative state of a BTS to locked means it has to discontinue all RF emission on all Radio Carriers and all telecommunication transmissions on

42、 all Channels of all Baseband Transceivers, i.e., Radio Carriers, Channels and Baseband Transceivers are in Disabled, Dependency state. The administrative state at the BTS site is also used to provide information e.g., for a local MMI user at a BTS site. The locked state of a 12.21 managed object me

43、ans that BSC has disconnected all the calls that go through the resource that is represented by the managed object. No new traffic is connected through this resource any more. The shutting down state means that no new traffic is connected through this resource any more. The on-going calls remain. Th

44、e unlocked state means that new traffic is allowed through the resource represented by the managed object. 5.3.2 Operational State and Availability Status ITU-T Recommendation X.731 gives the following definitions for the values of the operational state attribute: - disabled: the resource is totally

45、 inoperable and unable to provide service to the user(s); - enabled: the resource is partially or fully operable and available for use. In the present document the value Disabled represents the following conditions that the resources could have: - hardware or software is not installed; - power is tu

46、rned off; - failure has occurred; - radio parameters has not yet been set by elementary procedures, therefore, the resource is off line. The availability status elaborates the operational state attribute. In the present document the following values are used (availability status is a set value): In

47、test: the resource is undergoing a test procedure. Failed: the resource has an internal fault that prevents it from operating. The operational state is disabled. Power off: the resource requires power to be applied and is not powered on. The operational state is disabled. Off line: the resource requ

48、ires some manual and/or automatic operation(s) to be performed to make it available for the use. Dependency: the resource cannot operate because some other resource on which it depends is unavailable. The operational state is disabled. Degraded: the service available from the resource is degraded in

49、 some respect, such as in speed or operating capacity. The operational state is enabled. Not installed: the hardware or the software associated with the managed object has not been installed at the site. Operational state is disabled. Figure 2 illustrates the operational state and availability status behaviour of GSM 12.21 objects (i.e., Site Manager, BTS, Radio Carrier, and Baseband Transceiver) during initialization. The initial value of the administrative state is locked. ETSI ETSI TS 152 021 V15.0.0 (2018-07)153GPP TS 52.021 version 15.0.0 Releas