ETSI TS 151 026-2017 Digital cellular telecommunications system (Phase 2+) (GSM) Base Station System (BSS) equipment specification Part 4 Repeaters (V14 0 0 3GPP TS 51 026 version .pdf

《ETSI TS 151 026-2017 Digital cellular telecommunications system (Phase 2+) (GSM) Base Station System (BSS) equipment specification Part 4 Repeaters (V14 0 0 3GPP TS 51 026 version .pdf》由会员分享，可在线阅读，更多相关《ETSI TS 151 026-2017 Digital cellular telecommunications system (Phase 2+) (GSM) Base Station System (BSS) equipment specification Part 4 Repeaters (V14 0 0 3GPP TS 51 026 version .pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 151 026 V14.0.0 (2017-04) Digital cellular telecommunications system (Phase 2+) (GSM); Base Station System (BSS) equipment specification; Part 4: Repeaters (3GPP TS 51.026 version 14.0.0 Release 14) TECHNICAL SPECIFICATION GLOBAL SYSTEM FOR MOBILE COMMUNICATIONSRETSI ETSI TS 151 026 V14.0.0

2、 (2017-04)13GPP TS 51.026 version 14.0.0 Release 14Reference RTS/TSGR-0651026ve00 Keywords GSM ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfe

3、cture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be

4、 modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretari

5、at. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, plea

6、se send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written perm

7、ission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand t

8、he ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 151

9、 026 V14.0.0 (2017-04)23GPP TS 51.026 version 14.0.0 Release 14Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-membe

10、rs, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant

11、to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document

12、. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to t

13、he corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ a

14、nd “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 151 026 V14.0.0 (2017-04)33GPP TS 51.026 version 14.0.

15、0 Release 14Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 5g31 Scope 6g32 References 6g33 Definitions and abbreviations . 7g33.1 Definitions 7g33.2 Abbreviations . 7g34 General . 7g34.1 Radio frequency bands . 8g34.2 Test environments 8g34.2.1 Normal te

16、st environment 8g34.2.2 Extreme test environment . 8g34.2.3 Extreme temperature . 8g34.3 Manufacturers declarations 9g34.4 Methods of measurement . 9g35 Spurious emissions . 9g35.1 Test purpose . 9g35.2 Test case . 9g35.3 Conformance requirement 10g35.4 Reference requirement . 11g36 Intermodulation

17、attenuation . 11g36.1 Test purpose . 11g36.2 Test case . 11g36.3 Conformance requirement 11g36.4 Reference requirement . 11g37 Out of band gain . 12g37.1 Test purpose . 12g37.2 Test case . 12g37.3 Conformance requirement 12g37.4 Reference requirement . 12g38 Frequency error 12g38.1 Test purpose . 12

18、g38.2 Test case . 13g38.3 Conformance requirement 13g38.4 Reference requirement . 13g39 Modulation accuracy at GMSK modulation. 13g39.1 Test purpose . 13g39.2 Test case . 13g39.3 Conformance requirement 14g39.4 Reference requirement . 14g310 Modulation accuracy at 8-PSK, QPSK, 16-QAM, 32-QAM or AQPS

19、K modulation 14g310.1 Test purpose . 14g310.2 Test case . 14g310.3 Conformance requirement 15g310.4 Reference requirement . 15g3Annex A (informative): Testing of gain for part band repeaters . 16g3ETSI ETSI TS 151 026 V14.0.0 (2017-04)43GPP TS 51.026 version 14.0.0 Release 14A.1 Rationale for this t

20、est 16g3A.2 Gain outside pass band . 16g3A.2.1 Test purpose . 16g3A.2.2 Test case . 16g3A.2.3 Conformance requirement 16g3Annex B (informative): Change history . 17g3History 18g3ETSI ETSI TS 151 026 V14.0.0 (2017-04)53GPP TS 51.026 version 14.0.0 Release 14Foreword This Technical Specification has b

21、een produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identif

22、ying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes

23、of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. ETSI ETSI TS 151 026 V14.0.0 (2017-04)63GPP TS 51.026 version 14.0.0 Release 141 Scope The present document describes the Radio F

24、requency (RF) tests for GSM repeaters (frequency bands according to clause 4.1) which receive, amplify, and retransmit a received Mobile Station (MS) signal in the GSM MS transmit band and simultaneously receive, amplify and retransmit a received Base Transceiver Station (BTS) RF signal in the GSM B

25、TS transmit band. The present document is applicable to repeaters meeting the requirements of either GSM Phase 2 or GSM Phase 2+. Unless otherwise stated, all tests are applicable to repeaters meeting Phase 2 and/or Phase 2+ GSM requirements, because the requirements of the Phase 2 and Phase 2+ core

26、 GSM specifications which are referenced in the test are consistent. Most differences between Phase 2 and Phase 2+ requirements represent Phase 2+ features which are optional for the BSS to support. 2 References The following documents contain provisions which, through reference in this text, consti

27、tute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. In the case of a r

28、eference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 3GPP TR 21.905: “Vocabulary for 3GPP Specifications“. 2 ETS 300 019-1-0: “Equipment Engineering (EE): Environmental

29、 conditions and environmental tests for telecommunications equipment Part 1-0; Classification of environmental conditions; Introduction“. 3 ETS 300 019-1-3: “Equipment Engineering (EE): Environmental conditions and environmental tests for telecommunications equipment Part 1-3; Classification of envi

30、ronmental conditions, Stationary use at weather-protected locations“. 4 ETS 300 019-1-4: “Equipment Engineering (EE): Environmental conditions and environmental tests for telecommunications equipment Part 1-4; Classification of environmental conditions, Stationary use at non-weather-protected locati

31、ons“. 5 ITU-R Rec. SM.329: “Spurious emissions“. 6 void. 7 IEC 60068-2: “Basic environmental testing procedures: Part 2 Tests“. 8 IEC 721: “Classification of environmental conditions“. 9 3GPP TS 51.010-1: “Mobile Station (MS) conformity specification”. 10 3GPP TS 51.021: “Base Station System (BSS) e

32、quipment specification; Radio aspects”. 11 ETSI ETR 027: “Methods of measurement for private mobile radio equipment“. 12 ETSI ETR 028: “Uncertainties in the measurement of mobile radio equipment characteristics“. 13 3GPP TS 45.005: “Radio transmission and reception“. ETSI ETSI TS 151 026 V14.0.0 (20

33、17-04)73GPP TS 51.026 version 14.0.0 Release 143 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: broadband repeater: repeater which is designed for operation on any combination of ARFCNs (up to a specified maximum num

34、ber) within the operating band of the repeater. channelized repeater: repeater which is designed for operation on a specified subset of ARFCNs within the operating band of the repeater. The subset of ARFCNs may be determined during the manufacture of the repeater, or may be programmable. GSM: Unless

35、 otherwise specified, references to GSM include all radio frequency bands according to clause 4.1. operating band: the frequency range in which GSM operates. pass band: frequency range that the repeater operates in with operational configuration. NOTE 1: This frequency range can correspond to one or

36、 several consecutive nominal channels. If they are not consecutive each subset of channels shall be considered as an individual pass band. NOTE 2: A repeater can have one or several pass bands. repeater: bi-directional Radio Frequency (RF) amplifier which can amplify and transmit a received Mobile S

37、tation (MS) signal in the GSM MS transmit band, simultaneously it can amplify and transmit a received Base Transceiver Station (BTS) RF signal in the GSM BTS transmit band. repeater system using frequency shift: repeater system consisting of two different elements, a master unit close to the BTS and

38、 at least one remote unit close to the area to be covered. NOTE 3: The master unit amplifies the channels from the BTS and shifts them to different GSM channels. In the remote unit the shifted channels from the master unit will be transferred back to the original channels and amplified. This is vali

39、d for the downlink signals as well as for the uplink signals. spurious emissions: emissions at frequencies other than those of the carrier and sidebands associated with normal modulation and switching. subchannel power imbalance ratio on downlink: as defined in 3GPP TS 45.004 21. 3.2 Abbreviations F

40、or the purposes of the present document, the following abbreviations apply: BTS Base Transceiver Station MS Mobile Station RF Radio Frequency SCPIR_DL Subchannel Power Imbalance Ratio on DownLink Abbreviations used within the GSM specifications are given in 3GPP TR 21.905 1. 4 General A repeater can

41、 be designed to amplify the whole transmit RF band or just a part of the band. In the latter case the repeater can be either Broadband, with frequency band selective filtering, or channelized, with channel selective filtering. ETSI ETSI TS 151 026 V14.0.0 (2017-04)83GPP TS 51.026 version 14.0.0 Rele

42、ase 144.1 Radio frequency bands A repeater, as having a bi-directional amplifier capability, can amplify and transmit a received MS signal in the MS transmit band, simultaneously it can amplify and transmit a received BTS signal in the BTS transmit band. The relevant MS and BTS transmit bands for th

43、e present document are the MS and BTS transmit bands as defined in 3GPP TS 45.005 13, clause 2. A repeater is designed to operate in one or several pass bands within the MS and BTS transmit bands as defined in 3GPP TS 45.005 13, clause 2. In this document, such MS and BTS relevant bands are herein r

44、eferred as the repeater operating bands, as defined in clause 3.1. Repeater operating band(s) and repeater pass band(s) are part of clause 4.3 Manufacturers declarations. Table 1: void NOTE: In some circumstances, for instance when an operator (or more than one operator who co-ordinate the use of re

45、peaters), is not allocated a complete band, it may be necessary to restrict the frequency range of operations of repeaters. In these circumstances, the test of “Gain outside pass band“ in annex A may be used to verify the performance of the repeater. 4.2 Test environments For each test in the presen

46、t document, the environmental conditions under which the repeater is to be tested are defined. 4.2.1 Normal test environment When a normal test environment is specified for a test, the test should be performed under any combination of conditions between the minimum and maximum limits stated in table

47、 2. Table 2: Limits of conditions for Normal Test Environment Condition Minimum Maximum Barometric pressure 86 kPa 106 kPa Temperature 15C 30CRelative Humidity 20 % 85 % Power supply Nominal, as declared by the manufacturer Vibration NegligibleThe ranges of barometric pressure, temperature and humid

48、ity represent the maximum variation expected in the uncontrolled environment of a test laboratory. If it is not possible to maintain these parameters within the specified limits, the actual values shall be recorded in the test report. NOTE: This may, for instance, be the case for measurements of rad

49、iated emissions performed on an open field test site. 4.2.2 Extreme test environment The manufacturer shall declare one of the following: a) the equipment class for the equipment under test, as defined in ETS 300 019-1-3 3; b) the equipment class for the equipment under test, as defined in ETS 300 019-1-4 4; c) for equipment that does not comply to an ETS 300 019-1 2 class, the relevant classes from IEC 721 8 documentation for temperature, humidity and vibration shall be declared. NOTE: Reduced functionality for conditions tha