ETSI TS 125 214-2018 Universal Mobile Telecommunications System (UMTS) Physical layer procedures (FDD) (V15 0 0 3GPP TS 25 214 version 15 0 0 Release 15).pdf

《ETSI TS 125 214-2018 Universal Mobile Telecommunications System (UMTS) Physical layer procedures (FDD) (V15 0 0 3GPP TS 25 214 version 15 0 0 Release 15).pdf》由会员分享，可在线阅读，更多相关《ETSI TS 125 214-2018 Universal Mobile Telecommunications System (UMTS) Physical layer procedures (FDD) (V15 0 0 3GPP TS 25 214 version 15 0 0 Release 15).pdf（139页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 125 214 V15.0.0 (2018-07) Universal Mobile Telecommunications System (UMTS); Physical layer procedures (FDD) (3GPP TS 25.214 version 15.0.0 Release 15) TECHNICAL SPECIFICATION ETSI ETSI TS 125 214 V15.0.0 (2018-07)13GPP TS 25.214 version 15.0.0 Release 15Reference RTS/TSGR-0625214vf00 Keywo

2、rds UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded

3、 from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or

4、perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to

5、revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/C

6、ommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the writt

7、en authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2018. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTETMare trademarks of ETSI registered

8、for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSMand the GSM logo are trademarks registered and owned by the GSM Association. ETSI ETSI TS 125 214 V15.0.0 (2018-07)23GPP TS 25.214 version 15.0.0 Release 15Intellectual

9、 Property Rights Essential patents IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual

10、Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR

11、 searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademark

12、s and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document d

13、oes not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports usi

14、ng their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In

15、the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deli

16、verables except when used in direct citation. ETSI ETSI TS 125 214 V15.0.0 (2018-07)33GPP TS 25.214 version 15.0.0 Release 15Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 7g31 Scope 8g32 References 8g33 Definitions and abbreviations . 8g33.1 Definitions

17、 8g33.2 Abbreviations . 10g34 Synchronization procedures . 11g34.1 Cell search 11g34.2 Common physical channel synchronization . 11g34.2.1 P-CCPCH radio frame timing . 11g34.2.2 S-CCPCH soft combining timing . 11g34.2.3 Radio frame timing on the MBSFN layer . 11g34.2.4 Secondary serving HS-DSCH cell

18、 timing . 12g34.2.5 HS-DSCH cell timing when Multiflow is configured . 12g34.3 DPCCH/DPDCH/F-DPCH synchronization 12g34.3.1 Synchronization primitives . 12g34.3.1.1 General 12g34.3.1.2 Downlink synchronization primitives . 12g34.3.1.3 Uplink synchronization primitives 14g34.3.2 Radio link establishm

19、ent and physical layer reconfiguration for dedicated channels . 14g34.3.2.1 General 14g34.3.2.2 Node B radio link set state machine 15g34.3.2.3 Synchronization procedure A 15g34.3.2.3A Synchronization procedure AA . 16g34.3.2.4 Synchronization procedure B 17g34.3.3 Radio link monitoring . 17g34.3.3.

20、1 Downlink radio link failure . 17g34.3.3.2 Uplink radio link failure/restore in CELL_DCH state 17g34.3.3.2A Uplink radio link failure/restore in CELL_FACH state and IDLE mode . 18g34.3.4 Transmission timing adjustments . 18g35 Power control . 18g35.1 Uplink power control 18g35.1.1 PRACH . 18g35.1.1

21、.1 General 18g35.1.1.2 Setting of PRACH control and data part power difference . 18g35.1.2 DPCCH/DPDCH/DPCCH2 19g35.1.2.1 General 19g35.1.2.2 Ordinary transmit power control . 19g35.1.2.2.1 General 19g35.1.2.2.2 Algorithm 1 for processing TPC commands . 22g35.1.2.2.3 Algorithm 2 for processing TPC c

22、ommands . 22g35.1.2.2.4 Algorithm 3 for processing TPC commands . 23g35.1.2.2A Ordinary transmit power control for DPCCH2 . 25g35.1.2.3 Transmit power control in compressed mode . 25g35.1.2.3A Transmit power control in compressed mode for DPCCH2 28g35.1.2.4 Transmit power control in the uplink DPCCH

23、 power control preamble . 28g35.1.2.5 Setting of the uplink DPCCH/DPDCH relative powers 28g35.1.2.5.1 General 28g35.1.2.5.2 Signalled gain factors 29g35.1.2.5.3 Computed gain factors . 29g35.1.2.5.4 Setting of the uplink DPCCH/DPDCH relative powers in compressed mode . 30g3ETSI ETSI TS 125 214 V15.0

24、.0 (2018-07)43GPP TS 25.214 version 15.0.0 Release 155.1.2.5A Setting of the uplink HS-DPCCH power relative to DPCCH or DPCCH2 power 30g35.1.2.5B Setting of the uplink E-DPCCH and E-DPDCH powers relative to DPCCH power. 33g35.1.2.5B.1 E-DPCCH/DPCCH when one transport block is transmitted on E-DCH 33

25、g35.1.2.5B.1A E-DPCCH/DPCCH when two transport blocks are transmitted on E-DCH (rank-2) 35g35.1.2.5B.2 E-DPDCH/DPCCH . 35g35.1.2.5C Setting of the uplink DPCCH gain factor when no DPDCH is configured . 39g35.1.2.5D Setting of the uplink S-DPCCH power relative to DPCCH power . 39g35.1.2.5D.1 Setting

26、of the uplink S-DPCCH/DPCCH power ratio when less than two transport blocks are transmitted on E-DCH . 39g35.1.2.5D.2 Setting of the uplink S-DPCCH/DPCCH power ratio when two transport blocks are transmitted on E-DCH (rank-2) . 40g35.1.2.5E Setting of the uplink S-E-DPCCH power relative to DPCCH pow

27、er . 40g35.1.2.5F Setting of the uplink S-E-DPDCH power relative to E-DPDCH power . 41g35.1.2.6 Maximum and minimum power limits 41g35.1.3 Void 44g35.2 Downlink power control . 44g35.2.1 DPCCH/DPDCH/F-DPCH . 44g35.2.1.1 General 44g35.2.1.2 Ordinary transmit power control . 45g35.2.1.2.1 UE behaviour

28、 . 45g35.2.1.2.2 UTRAN behaviour 46g35.2.1.3 Power control in compressed mode 47g35.2.1.4 Power scaling of DPDCH with POSRB48g35.2.2 Void 49g35.2.3 Void 49g35.2.4 AICH 49g35.2.5 PICH . 49g35.2.6 S-CCPCH 49g35.2.7 Void 49g35.2.8 Void 49g35.2.9 Void 49g35.2.10 HS-SCCH . 49g35.2.11 HS-PDSCH . 49g35.2.1

29、2 E-AGCH . 50g35.2.13 E-HICH . 50g35.2.14 E-RGCH . 50g35.2.15 MICH 50g35.2.16 S-CPICH . 50g35.2.17 F-TPICH . 50g35.2.18 D-CPICH 50g35.2.19 E-ROCH . 50g36 Random access procedure 50g36.1 Physical random access procedure . 50g36.1.1 RACH sub-channels . 52g36.1.2 RACH access slot sets 52g36.1A Physical

30、 random access procedure for Enhanced Uplink in CELL_FACH state and IDLE mode . 53g36.2 Void 55g36A HS-DSCH-related procedures 55g36A.1 General procedure 55g36A.1.1 UE procedure for receiving HS-DSCH and HS-SCCH in the CELL_DCH state . 57g36A.1.1A UE procedure for receiving HS-DSCH and HS-SCCH in CE

31、LL_FACH state 61g36A.1.1B UE procedure for receiving HS-DSCH and HS-SCCH in the URA_PCH and CELL_PCH states 62g36A.1.2 UE procedure for reporting channel quality indication (CQI) and precoding control indication (PCI) 63g36A.1.2.1 CQI reporting procedure in case the UE is not configured in MIMO mode

32、 and not configured in MIMO mode with four transmit antennas in any cell . 63g36A.1.2.2 Composite PCI/CQI reporting procedure in case the UE is configured in MIMO mode 65g36A.1.2.3 Composite NTBP/PCI/CQI reporting procedure in case the UE is configured in MIMO mode with four transmit antennas . 68g3

33、6A.1.3 Node B procedure for transmitting the HS-DSCH and HS-SCCH . 69g36A.1.3.1 Node B procedure for transmitting the HS-DSCH and HS-SCCH in the CELL_DCH state 69g3ETSI ETSI TS 125 214 V15.0.0 (2018-07)53GPP TS 25.214 version 15.0.0 Release 156A.1.3.2 Node B procedure for transmitting the HS-DSCH an

34、d HS-SCCH in the CELL_FACH state 70g36A.1.3.3 Node B procedure for transmitting the HS-DSCH and HS-SCCH in the URA_PCH or CELL_PCH state . 71g36A.2 Channel quality indicator (CQI) definition. 71g36A.2.1 CQI definition when the UE is not configured in MIMO mode and not configured in MIMO mode with fo

35、ur transmit antennas . 71g36A.2.2 CQI definition when the UE is configured in MIMO mode . 72g36A.2.2A CQI definition when the UE is configured in MIMO mode with four transmit antennas . 73g36A.2.3 CQI tables . 75g36A.3 Operation during compressed mode on the associated DPCH or F-DPCH 85g36A.4 Precod

36、ing control indication (PCI) definition 85g36A.4.1 PCI definition when the UE is configured in MIMO mode 85g36A.4.2 PCI definition when the UE is configured in MIMO mode with four transmit antennas . 86g36B E-DCH related procedures . 87g36B.1 ACK/NACK detection . 87g36B.2 Relative grants detection 8

37、8g36B.2A Absolute Grant Detection when the UE is configured with Implicit Grant Handling 88g36B.3 E-DCH control timing 88g36B.3.0 UE procedure for switching the E-DCH TTI length due to an HS-SCCH order 88g36B.3.1 10 ms E-DCH TTI 89g36B.3.2 2 ms E-DCH TTI 89g36B.4 Operation during compressed mode . 9

38、0g36B.4.1 Uplink compressed mode 90g36B.4.2 Downlink compressed mode . 90g36C Discontinuous transmission and reception procedures . 90g36C.0 Discontinuous transmission/reception of DCH 91g36C.0.1 DL_DPCH_DYN_DRX and UL_DPCH_DYN_DTX . 91g36C.0.1.1 DL_DCH_FET_Config = 0 . 91g36C.0.1.2 DL_DCH_FET_Confi

39、g = 1 . 92g36C.1 Uplink CQI transmission 92g36C.2 Discontinuous uplink DPCCH/DPCCH2 transmission operation 93g36C.2.1 Uplink DPCCH burst pattern 93g36C.2.2 Uplink DPCCH preamble and postamble . 95g36C.2.2.1 Uplink DPCCH preamble and postamble for the DPCCH only transmission . 95g36C.2.2.2 Uplink DPC

40、CH preamble and postamble for the E-DCH transmission 95g36C.2.2.3 Uplink DPCCH preamble and postamble for the HS-DPCCH transmission 95g36C.3 Discontinuous downlink reception . 96g36C.3.1 Discontinuous downlink reception when the UE is in Multiflow mode . 98g36C.4 HS-SCCH orders 99g36C.5 Operation du

41、ring compressed mode . 99g37 Closed loop mode 1 transmit diversity . 100g37.1 General procedure 101g37.2 Determination of feedback information . 101g37.2.1 End of frame adjustment . 102g37.2.2 Normal initialisation . 102g37.2.3 Operation during compressed mode . 103g37.2.3.1 Downlink in compressed m

42、ode and uplink in normal mode . 103g37.2.3.2 Both downlink and uplink in compressed mode . 103g37.2.3.3 Uplink in compressed mode and downlink in normal mode . 104g37.2.4 Initialisation during compressed mode . 104g37.2.4.1 Downlink in compressed mode . 104g37.2.4.2 Uplink in compressed mode 104g37.

43、3 Void 105g38 Idle periods for IPDL location method . 105g38.1 General . 105g38.2 Parameters of IPDL 105g38.3 Calculation of idle period position . 105g39 MIMO operation of HS-DSCH 107g39.1 General procedure 108g3ETSI ETSI TS 125 214 V15.0.0 (2018-07)63GPP TS 25.214 version 15.0.0 Release 1510 Uplin

44、k Closed Loop Transmit Diversity operation 109g310.1 General procedure 109g310.2 Downlink TPI transmission and control timing 111g310.3 Combining TPI bits from multiple radio links . 112g310.4 Operation during discontinuous uplink DPCCH operation 112g310.5 Operation during compressed mode . 112g310.

45、5.1 Uplink compressed mode 112g310.5.2 Downlink compressed mode . 112g310.6 HS-SCCH orders 112g311 Uplink MIMO 113g311.1 General procedure 115g311.2 Downlink TPI transmission and control timing 115g311.3 Combining TPI bits from radio links of the serving radio link set . 115g311.4 Operation during d

46、iscontinuous uplink DPCCH operation 116g311.5 Operation during compressed mode . 116g311.6 HS-SCCH orders 116g311.7 Uplink power control 116g312 MIMO operation of HS-DSCH with four transmit antennas . 116g312.1 General procedure 118g312.2 Symbol level interleaving . 118g312.3 Retransmission Procedur

47、es . 119g312.4 Precoding weight restriction . 120g312.5 HS-SCCH Orders . 120g3Annex A (informative): (no title) . 121g3A.1 Antenna verification . 121g3A.2 Computation of feedback information for closed loop mode 1 transmit diversity . 122g3Annex B (Informative): Power control . 123g3B.1 Downlink pow

48、er control timing . 123g3B.2 Example of implementation in the UE . 127g3B.3 UL power control when losing UL synchronization 127g3Annex C (Informative): Cell search procedure 128g3Annex D (Informative): F-TPICH Transmission . 129g3Annex E (informative): Change history . 130g3History 138g3ETSI ETSI TS

49、 125 214 V15.0.0 (2018-07)73GPP TS 25.214 version 15.0.0 Release 15Foreword This Technical Specification (TS) has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of this present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TS