ETSI TS 123 101-2018 Universal Mobile Telecommunications System (UMTS) General Universal Mobile Telecommunications System (UMTS) architecture (V15 0 0 3GPP TS 23 101 version 15 0 0.pdf

《ETSI TS 123 101-2018 Universal Mobile Telecommunications System (UMTS) General Universal Mobile Telecommunications System (UMTS) architecture (V15 0 0 3GPP TS 23 101 version 15 0 0.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 123 101-2018 Universal Mobile Telecommunications System (UMTS) General Universal Mobile Telecommunications System (UMTS) architecture (V15 0 0 3GPP TS 23 101 version 15 0 0.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 123 101 V15.0.0 (2018-06) Universal Mobile Telecommunications System (UMTS); General Universal Mobile Telecommunications System (UMTS) architecture (3GPP TS 23.101 version 15.0.0 Release 15) TECHNICAL SPECIFICATION ETSI ETSI TS 123 101 V15.0.0 (2018-06)13GPP TS 23.101 version 15.0.0 Release

2、 15Reference RTS/TSGS-0223101vf00 Keywords UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice

3、 The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorizati

4、on of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be awa

5、re that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following se

6、rvices: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version

7、shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2018. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and

8、LTETMare trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSMand the GSM logo are trademarks registered and owned by the GSM Association. ETSI ETSI TS 123 101 V15.0.0 (2018-06)23GPP TS 23.10

9、1 version 15.0.0 Release 15Intellectual Property Rights Essential patents IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be f

10、ound in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR

11、Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The

12、 present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of tho

13、se trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to

14、technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/que

15、ryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and

16、“must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 123 101 V15.0.0 (2018-06)33GPP TS 23.101 version 15.0.0 Release 15Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 4g3Introduction 4g31 Scope 5g32 References

17、5g33 Definitions, symbols and abbreviations . 5g33.1 Definitions 5g33.2 Symbols 5g33.3 Abbreviations . 5g34 General . 6g35 Domains in UMTS . 6g35.1 Domain split . 7g35.2 User equipment Domain . 7g35.2.1 Mobile equipment Domain . 8g35.2.2 USIM Domain 8g35.3 Infrastructure Domain 8g35.3.1 Access Netwo

18、rk Domain 8g35.3.2 Core Network Domain 8g35.3.2.1 Serving Network Domain . 9g35.3.2.2 Home Network Domain 9g35.3.2.3 Transit Network Domain . 9g36 Functional Communication between UMTS domains . 9g36.1 Transport stratum . 11g36.2 Access Stratum . 11g36.3 Serving Stratum 12g36.4 Home Stratum 12g36.5

19、Application Stratum . 12g3Annex A (informative): Change History 13g3History 14g3ETSI ETSI TS 123 101 V15.0.0 (2018-06)43GPP TS 23.101 version 15.0.0 Release 15Foreword This Technical Specification has been produced by the 3rd Generation Partnership Project (3GPP). The contents of the present documen

20、t are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x

21、the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is increm

22、ented when editorial only changes have been incorporated in the document. Introduction UMTS will support a wide range of applications with different quality of service profiles. At present many of these applications are not possible to predict. Also the usage of the different applications are diffic

23、ult to predict i.e. it is not possible to optimise UMTS to only one set of applications. One conclusion of this is that UMTS must be built in such a way that it is flexible and possible to evolve so it will have a long technical lifetime. Therefore a modular approach is recommended when defining the

24、 network parts of UMTS. This is in line with the recommendation from GMM. In this context a module represents a part of a UMTS network i.e. one or several physical network nodes that together implements some functionality. The modular approach should also make UMTS possible to implement efficiently

25、in different environments. ETSI ETSI TS 123 101 V15.0.0 (2018-06)53GPP TS 23.101 version 15.0.0 Release 151 Scope This TS defines the basic physical and functional separation of UMTS. The contents of this specification is limited to those features that are common to all UMTS networks independent of

26、their origin. It identifies and names the reference points and functional groupings appearing at this level. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. - References are either specific (identified by d

27、ate of publication, edition number, version number, etc.) or non-specific. - For a specific reference, subsequent revisions do not apply. - For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference imp

28、licitly refers to the latest version of that document in the same Release as the present document. 1 ETSI SR 001 687: ETSI Global Multimedia Mobility (GMM) report. 2 UMTS 22.01: “Universal Mobile Telecommunications System (UMTS): Service aspects; Service principles“. 3 3GPP TS 24.002: “GSM - UMTS Pu

29、blic Land Mobile Network (PLMN) Access Reference Configuration“. 3 Definitions, symbols and abbreviations 3.1 Definitions Terms introduced in this document: Domain: The highest-level group of physical entities. Reference points are defined between domains. Stratum: Grouping of protocols related to o

30、ne aspect of the services provided by one or several domains. 3.2 Symbols For the purposes of the present document, the following symbols apply: Cu Reference point between USIM and ME Iu Reference point between Access and Serving Network domains Uu Reference point between User Equipment and Infrastr

31、ucture domains, UMTS radio interface Yu Reference point between Serving and Transit Network domains Zu Reference point between Serving and Home Network domains 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: USIM User Services Identity Module ME Mobile

32、EquipmentMT Mobile Termination MExE Mobile Station Application Execution Environment TE Terminal Equipment ETSI ETSI TS 123 101 V15.0.0 (2018-06)63GPP TS 23.101 version 15.0.0 Release 154 General The general UMTS architecture is modelled, at a high level, from both physical and functional viewpoints

33、. The physical aspects are modelled using the domain concept and the functional aspects are modelled using the strata concept. The two views are introduced separately and then the mapping between the views is discussed. This specification shows at a basic level physical and functional separations to

34、 allow a UMTS network to fit within the context of the IMT-2000 family of networks. It does not attempt to develop aspects of a UMTS network that are highly specific to that implementation. 5 Domains in UMTS The following figure shows the basic domains in UMTS as described in this section. User Equi

35、pment Domain Access Network Domain Core Network Domain Infrastructure Domain Cu Mobile Equipment Domain USIM Domain Home Network Domain Transit Network Domain Uu Iu Zu Yu Serving Network Domain NOTE : The domains identified in the figure will generally result from an evolution of existing network in

36、frastructures. The core network domain may result from evolutions of existing network infrastructures, e.g., a GSM infrastructure, a N-ISDN infrastructure, a B-ISDN infrastructure or a PDN infrastructure. The evolution of these infrastructures may be performed via the use of IWUs, hidden within the

37、domains shown in the figure. Figure 1: UMTS domains and reference points Cu = Reference point between USIM and ME Iu = Reference point between Access and Serving Network domains Uu = Reference point between User Equipment and Infrastructure domains, UMTS radio interface Yu = Reference point between

38、Serving and Transit Network domains Zu = Reference point between Serving and Home Network domains ETSI ETSI TS 123 101 V15.0.0 (2018-06)73GPP TS 23.101 version 15.0.0 Release 155.1 Domain split A basic architectural split is between the user equipment (terminals) and the infrastructure. This results

39、 in two domains: the User Equipment Domain and the Infrastructure domain. User equipment is the equipment used by the user to access UMTS services. User equipment has a radio interface to the infrastructure. The infrastructure consists of the physical nodes which perform the various functions requir

40、ed to terminate the radio interface and to support the telecommunication services requirements of the users. The infrastructure is a shared resource that provides services to all authorised end users within its coverage area. The reference point between the user equipment domain and the infrastructu

41、re domain is termed the “Uu“ reference point (UMTS radio interface). NOTE: The description assumes an access interface based on UTRA. However, the physical and functional separation described in this document is general and is applicable also if other access technologies are used. 5.2 User equipment

42、 Domain This domain encompasses a variety of equipment types with different levels of functionality. These equipment types are referred to as user equipment (terminals), and they may also be compatible with one or more existing access (fixed or radio) interfaces e.g. dual mode UMTS-GSM user equipmen

43、t. The user equipment may include a removable smart card that may be used in different user equipment types. The user equipment is further sub-divided in to the Mobile Equipment Domain (ME) and the User Services Identity Module Domain (USIM). The reference point between the ME and the USIM is termed

44、 the “Cu“ reference point. For the purpose of UMTS Cellular networks the following definition applies: User Equipment is a device allowing a user access to network services. For the purpose of 3GPP specifications the interface between the UE and the network is the radio interface. A User Equipment c

45、an be subdivided into a number of domains, the domains being separated by reference points. Currently defined domains are the USIM and ME Domains. The ME Domain can further be subdivided into several components showing the connectivity between multiple functional groups. These groups can be implemen

46、ted in one or more hardware devices. An example of such a connectivity is the TE MT interface. Further, an occurrence of User Equipment is an MS for GSM as defined in TS 24.002 3. The figure below shows the Functional Model for the User Equipment, UE. UE MEUSIM MT TEFigure 1a: Functional Model for t

47、he User Equipment The 07- and 27-series refer to physical instances of this Functional Model. The figure below shows an example of a physical configuration as it could be used in these specifications. The boxes, in this figure, refer to physical elements. The names within brackets are just provided

48、to map the functional blocks from the figure above onto physical elements. ETSI ETSI TS 123 101 V15.0.0 (2018-06)83GPP TS 23.101 version 15.0.0 Release 15UICC (USIM) Handset (MT) PC (TE) R Figure 1b: Example of physical configuration 5.2.1 Mobile equipment Domain The Mobile Equipment performs radio

49、transmission and contains applications. The mobile equipment may be further sub-divided into several entities, e.g. the one which performs the radio transmission and related functions, Mobile Termination, MT, and the one which contains the end-to-end application or (e.g. laptop connected to a mobile phone), Terminal Equipment. TE. This separation is used in the description of the functional communication in figure 3 but no reference point is defined in this specification. 5.2.2 USIM Domain The USIM contains data and procedures which unambiguously and secu