ETSI TS 102 795-2011 Electromagnetic compatibility and Radio spectrum Matters (ERM) digital Private Mobile Radio (dPMR) Part 3 Requirements catalogue (V2 1 1)《电磁兼容性和无线频谱事务(ERM) 数字专.pdf

《ETSI TS 102 795-2011 Electromagnetic compatibility and Radio spectrum Matters (ERM) digital Private Mobile Radio (dPMR) Part 3 Requirements catalogue (V2 1 1)《电磁兼容性和无线频谱事务(ERM) 数字专.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 102 795-2011 Electromagnetic compatibility and Radio spectrum Matters (ERM) digital Private Mobile Radio (dPMR) Part 3 Requirements catalogue (V2 1 1)《电磁兼容性和无线频谱事务(ERM) 数字专.pdf（89页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 102 795 V2.1.1 (2011-06)Technical Specification Electromagnetic compatibility and Radio spectrum Matters (ERM);digital Private Mobile Radio (dPMR);Part 3: Requirements catalogueETSI ETSI TS 102 795 V2.1.1 (2011-06)2Reference RTS/ERM-TGDMR-291 Keywords digital, mobile, private, radio ETSI 65

2、0 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downl

3、oaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference

4、 shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is a

5、vailable at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. T

6、he copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2011. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of

7、 ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 102 795 V2.1.1 (2011-06)3Contents Intellectual Property Rights 4g3Foreword . 4g31 Scope 5g32 References 5g32.1 Norma

8、tive references . 5g32.2 Informative references 5g33 Definitions and abbreviations . 6g33.1 Definitions 6g33.2 Abbreviations . 6g34 dPMR requirements catalogue . 7g34.1 Framing 7g34.1.1 Addressing 10g34.1.1.1 All Call 10g34.1.1.2 Dialling Plan . 11g34.1.1.3 TPID 30g34.1.2 Base Station framing . 31g3

9、4.1.3 Channel Access . 38g34.1.3.1 OACSU . 44g34.1.3.2 PTT Call 44g34.1.4 End Frame. 44g34.1.5 Message Frame . 48g34.1.5.1 Message Information field 54g34.1.6 Payload . 59g34.1.6.1 Packet data 59g34.1.6.2 Short data 64g34.1.6.3 T1 data 67g34.1.6.4 T2 data 71g34.1.6.5 Voice . 76g34.1.6.5.1 Attached d

10、ata . 76g34.1.6.5.2 Late entry . 77g34.1.6.5.3 Slow user data . 78g34.1.7 Powersave. 79g34.1.8 Superframe 82g34.1.8.1 Traffic Channel . 82g34.1.8.2 Voice Traffic Channel . 88g3History 89g3ETSI ETSI TS 102 795 V2.1.1 (2011-06)4Intellectual Property Rights IPRs essential or potentially essential to th

11、e present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI

12、 in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existen

13、ce of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum

14、 Matters (ERM). ETSI ETSI TS 102 795 V2.1.1 (2011-06)51 Scope The present document is to provide a catalogue of requirements extracted from ETSI Specifications. The catalogues has been written based on the test specification framework defined in TS 102 351 2. 2 References References are either speci

15、fic (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not f

16、ound to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documen

17、ts are necessary for the application of the present document. 1 ETSI TS 102 658 (V2.1.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Digital Private Mobile Radio (dPMR) using FDMA with a channel spacing of 6,25 kHz“. 2 ETSI TS 102 351 (V2.1.1): “Methods for Testing and Specific

18、ation (MTS); Internet Protocol Testing (IPT); IPv6 Testing: Methodology and Framework“. 3 ETSI TS 102 490 (V1.3.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Peer-to-Peer Digital Private Mobile Radio using FDMA with a channel spacing of 6,25 kHz with e.r.p. of up to 500 mW“. 2

19、.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI ETS 300 230: “Radio Equipment and Systems (RES); Land mobile service; Binary Interchange of Informati

20、on and Signalling (BIIS) at 1 200 bit/s (BIIS 1 200)“. i.2 IEC EN 61162-1: “Maritime navigation and radiocommunication equipment and systems - Digital interfaces - Part 1: Single talker and multiple listeners“. ETSI ETSI TS 102 795 V2.1.1 (2011-06)63 Definitions and abbreviations 3.1 Definitions For

21、 the purposes of the present document, the following terms and definitions apply: base station: two frequency duplex equipment with uplink access and downlink re-transmission conditionally mandatory: requirement that is supported by a standard conformant equipment if and only if the condition(s) sta

22、ted within its requirement text are met NOTE: If one of these conditions is not met the requirement is considered to be not applicable. EXAMPLE: Such a condition may be the support of an optional higher level requirement by the equipment. conditionally optional: requirement that may be supported by

23、a standard conformant equipment if and only if the condition(s) stated within its requirement text are met NOTE: If one of these conditions is not met the requirement is considered to be not applicable. mandatory: requirement that is supported by a standard conformant equipment Mobile Station (MS):

24、handheld and fixed stations that are not repeaters are included Mode 1: peer to peer (direct mode) operation without Base Stations or infrastructure Mode 2: dPMR systems incorporating one or more Base Stations for repeating or providing system gateways Mode 3: dPMR systems operating under a managed

25、access mode in systems incorporating one or more Base Stations not applicable: requirement that does not have to be met by a standard conformant equipment optional: requirement that may be supported by a standard conformant equipment 3.2 Abbreviations For the purposes of the present document, the fo

26、llowing abbreviations apply: ACK ACKnowledgment AI Air Interface ARQ Automatic Retransmission reQuest BS2 Mode 2 Repeater BS3 Mode 3 Repeater CC Colour CodeCCH Control CHannel CI Call InformationCont Continuation flag CRC Cyclic Redundancy Checksum for data error detection DP Data Position DPMR Conf

27、igured Services and Facilities ET End Type FDMA Frequency Division Multiple Access FEC Forward Error Correction FN Frame Numbering HI Header Information HT Header Type ID IDentifierM1 Mode 1 MS M2 Mode 2 MS M3 Mode 3 MS MI Message Information MS Mobile Station ETSI ETSI TS 102 795 V2.1.1 (2011-06)7M

28、T Message Type NACK Negative ACKnowledgment OACSU Off Air Call Set Up PAR PARameter dataPDF Packet Data Format RF Radio Frequency RSSI Received Signal Strength Indication SLD SLow Data SYNC SYNChronization TCH Traffic CHannel 4 dPMR requirements catalogue 4.1 Framing RQ_001_0401 Framing TS 102 658 1

29、 Clause: 4.2.2.2 Type: Mandatory Applies to: M1, M2, M3 Requirement: All transmissions are made up from 80 ms (384 bits) frames. Normal frames (not packet data) are the concatenation of: 24 bits of either FrameSync or ColourCode 72 bits of Control Channel data Followed by 4 blocks of 72 bits of payl

30、oad. Specification Text: The FDMA transmission is made up of 80 ms payload frames, each comprising 384 bits. Payload frame: a b c d e f a: 24 bits FrameSync2 (FS2) or ColourCode (CC) bits b: 72 bits Control Channel (CCH) data c: 72 bits Traffic channel (TCH) d: 72 bits TCH e: 72 bits TCH f: 72 bits

31、TCH Family: No Duplicates Test Purposes: TP_PMR_0401_01 (Conformance), TP_PMR_0401_02 (Conformance), TP_PMR_0401_03 (Conformance) RQ_001_0402 Framing TS 102 658 1 Clause: 4.2.3.1 Type: Mandatory Applies to: M1, M2, M3 Requirement: All normal (non packet data) transmissions are made up from an integr

32、al number of superframes. Specification Text: The sequence is illustrated in figure 4.12. These transmissions are always started with a Header frame containing a preamble (for bit synchronization) and a frame synch (for frame synchronization). The Header is followed by a series of Superframes that c

33、ontain both the payload (voice or data) and the information about the call such that receiving stations can implement late entry. A call always consists of an integral number of superframes and is terminated by an End frame. Family: No Duplicates Test Purposes: None ETSI ETSI TS 102 795 V2.1.1 (2011

34、-06)8RQ_001_0403 Framing TS 102 658 1 Clause: 4.2.2.2.1 Type: Mandatory Applies to: M1, M2, M3 Requirement: Each superframe is the concatenation of four 80 ms frames. Specification Text: Four 80 ms payload frames illustrated in figure 4.8 are concatenated to form a superframe of 320 ms. Family: No D

35、uplicates Test Purposes: TP_PMR_0403_01 (Conformance), TP_PMR_0403_03 (Conformance), TP_PMR_0403_02 (Conformance) RQ_001_0404 Framing TS 102 658 1 Clause: 4.2.3.1 Type: Mandatory Applies to: M1, M2, M3 Requirement: Normal calls with voice or data continuous transmission generated by the radio will s

36、tart with a Header frame, an integral number of superframes and then terminated by an End frame. Specification Text: Voice or data payload continuous transmission: These transmissions are always started with a Header frame containing a preamble (for bit synchronisation) and a frame synch (for frame

37、synchronisation). The Header is followed by a series of Superframes that contain both the payload (voice or data) and the information about the call such that receiving stations can implement late entry. A call always consists of an integral number of superframes and is terminated by an End frame. F

38、amily: No Duplicates Test Purposes: TP_PMR_0404_01 (Conformance), TP_PMR_0404_02 (Conformance), TP_PMR_0404_03 (Conformance) RQ_001_0405 Framing TS 102 658 1 Clause: 4.2.3.2 Type: Mandatory Applies to: M1, M2 Requirement: Calls generated by the radio for the purposes of call set-up or service reques

39、t etc will be that of a concatenated Header frame and an End frame. Specification Text: The transmission illustrated in figure 4.13 may be sent by Mode 1 and Mode 2 systems on a traffic channel at the start of a call. They are a concatenation of a Header frame and an End frame. Their purpose is to i

40、nform the receiving station of the call, type of call or information required. Family: No Duplicates Test Purposes: TP_PMR_0405_01 (Conformance), TP_PMR_0405_02 (Conformance) RQ_001_0406 Framing TS 102 658 1 Clause: 4.2.3.3 Type: Conditionally Mandatory Applies to: M1, M2, M3 Requirement: Calls gene

41、rated by the radio for the purposes of acknowledgements will be simply a Header frame. Specification Text: Traffic channel acknowledgements are sent in response to applicable messages back to the originator. Acknowledgements are a type of Header that contains information such as confirmation of rece

42、ived data, errors in received data, etc Family: No Duplicates Test Purposes: TP_PMR_0406_01 (Conformance), TP_PMR_0406_02 (Conformance), TP_PMR_0406_03 (Conformance), TP_PMR_0406_04 (Conformance) ETSI ETSI TS 102 795 V2.1.1 (2011-06)9RQ_001_0407 Framing TS 102 658 1 Clause: 4.2.3.5 Type: Conditional

43、ly Mandatory Applies to: M1, M2, M3 Requirement: IF the radio supports disconnection request THEN calls generated by the radio for the purposes of confirming the end of the series of exchanges of a call shall be the concatenation of a Header frame and End frame repeated once. Specification Text: Sen

44、ding stations can signal that all exchanges of a call have been completed by transmitting a disconnection request. This is a Header + End frame pair that is repeated illustrated in figure 4.16. Family: No Duplicates Test Purposes: TP_PMR_0407_01 (Conformance), TP_PMR_0407_02 (Conformance), TP_PMR_04

45、07_03 (Conformance), TP_PMR_0407_04 (Conformance) RQ_001_0408 Framing TS 102 658 1 Clause: 4.2.3.4 Type: Conditionally Mandatory Applies to: M1, M2, M3 Requirement: Calls generated by the radio for the purposes of status request responses will be a Header frame and End frame. Specification Text: Tra

46、ffic channel status request acknowledgements illustrated in figure 4.15 are sent by Mode 1 and Mode 2 systems. As the status information is contained within the End frame then the response of a receiving station to a status request call shall be a Header + End frame pair. Family: No Duplicates Test

47、Purposes: TP_PMR_0408_01 (Conformance) RQ_001_0426 Framing TS 102 658 1 Clause: 10.2.7 Type: Conditionally Mandatory Applies to: M2 Requirement: Where a MS is part of a co-channel network and has sent an access header addressed to COCHI0, it shall transmit an ACK in the frame immediately following t

48、he final COCHI1 BS response. This ACK is addressed to the BS that is judged to have the best signal. Specification Text: c) MS shall determine from any received replies when the final (COCHI = 1) transmission in the sequence will occur, and the downlink channel may be assumed to be free. The BS orig

49、inated BS_Access Header demands an acknowledgement. The MS selects the COCH BS that will be used for the call and sends a acknowledgement with ID1 + 0 set to the co-channel gateway address that will be used for the call. (In this example BS3 has been selected). Family: No Duplicates Test Purposes: None ETSI ETSI TS 102 795 V2.1.1 (2011-06)10RQ_001_0428 Framing TS 102 658 1 Clause: 10.2.7.2 Type: Conditionally Mandatory Applies to: M2 Requirement: Where a MS is part of a co-channel network and receives an ind