ETSI TS 102 726-1-2014 Electromagnetic compatibility and Radio spectrum Matters (ERM) Conformance testing for Mode 1 of the digital Private Mobile Radio (dPMR ) Part 1 Protocol Impo.pdf

《ETSI TS 102 726-1-2014 Electromagnetic compatibility and Radio spectrum Matters (ERM) Conformance testing for Mode 1 of the digital Private Mobile Radio (dPMR ) Part 1 Protocol Impo.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 102 726-1-2014 Electromagnetic compatibility and Radio spectrum Matters (ERM) Conformance testing for Mode 1 of the digital Private Mobile Radio (dPMR ) Part 1 Protocol Impo.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 102 726-1 V2.2.1 (2014-09) Electromagnetic compatibility and Radio spectrum Matters (ERM); Conformance testing for Mode 1 of the digital Private Mobile Radio (dPMR); Part 1: Protocol Implementation Conformance Statement (PICS) proforma TECHNICAL SPECIFICATION ETSI ETSI TS 102 726-1 V2.2.1 (

2、2014-09)2Reference RTS/ERM-TGDMR-323 Keywords digital, mobile, PICS, radio, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Gr

3、asse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior

4、written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present doc

5、ument should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the fol

6、lowing services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version

7、 shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2014. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registere

8、d for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 102 726-1 V2.2.1 (2014-09)3Contents Intellectual

9、Property Rights 4g3Foreword . 4g3Modal verbs terminology 4g3Introduction 4g31 Scope 5g32 References 5g32.1 Normative references . 5g32.2 Informative references 5g33 Definitions and abbreviations . 6g33.1 Definitions 6g33.2 Abbreviations . 6g34 Conformance to this PICS proforma specification . 6g3Ann

10、ex A (normative): Protocol ICS proforma for TS 102 658 7g3A.1 Guidance for completing the PICS proforma . 7g3A.1.1 Purposes and structure 7g3A.1.2 Abbreviations and conventions 7g3A.1.3 Instructions for completing the PICS proforma 9g3A.2 Identification of the implementation 10g3A.2.1 Date of the st

11、atement 10g3A.2.2 Implementation Under Test (IUT) identification . 10g3A.2.3 System Under Test (SUT) identification 10g3A.2.4 Product supplier 10g3A.2.5 Client (if different from product supplier) 11g3A.2.6 ICS contact person 11g3A.3 Identification of the protocol 12g3A.4 Global statement of conform

12、ance . 12g3A.5 Entity 12g3A.6 M1 13g3A.7 M2 15g3A.8 M3 18g3A.9 M1 18g3A.9.1 M1 Features 18g3A.9.2 M1 Frames 19g3A.9.3 M1 Timers 19g3A.10 M2 20g3A.10.1 M2 Features 20g3A.10.2 M2 Frames 21g3A.10.3 M2 Timers 21g3A.11 BS2 Features 22g3A.11.1 BS2 Features 22g3A.11.2 BS2 Timers . 22g3A.11.3 BS2 Hangtimes

13、. 23g3A.12 M3 Features 23g3History 24 ETSI ETSI TS 102 726-1 V2.2.1 (2014-09)4Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI member

14、s and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.or

15、g). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the pre

16、sent document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document is part 1 of a multi-part deliverable covering the Conformance testing for Mode 1 of the digital Private Mobile

17、 Radio (dPMRTM), as identified below: Part 1: “Protocol Implementation Conformance Statement (PICS) proforma“; Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “Interoperability Test Suite Structure and Test Purposes (TSS Digital Private Mobile Radio using FDMA with a channel spacing of

18、6,25 kHz as defined in TS 102 658 1 in compliance with the relevant requirements, and in accordance with the relevant guidance given in ISO/IEC 9646-7 3 and ETS 300 406 4. The present document details in tabular form the implementation options, i.e. the optional functions additional to those which a

19、re mandatory to implement. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (incl

20、uding any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term

21、validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. 1 ETSI TS 102 658 (V2.4.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Digital Private Mobile Radio (dPMR) using FDMA with a channel spacing of 6,25

22、kHz“. 2 ISO/IEC 9646-1: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 3 ISO/IEC 9646-7: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementatio

23、n Conformance Statements“. 4 ETSI ETS 300 406: “Methods for testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. 2.2 Informative references The following referenced documents are not necessary for the application of the present docum

24、ent but they assist the user with regard to a particular subject area. Not applicable. ETSI ETSI TS 102 726-1 V2.2.1 (2014-09)63 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in TS 102 658 1, ISO/IEC 9646-1 2, ISO/IEC 9646-7 3

25、 and the following apply: Implementation Conformance Statement (ICS): statement made by the supplier of an implementation or system claimed to conform to a given specification, stating which capabilities have been implemented NOTE: The ICS can take several forms: protocol ICS, profile ICS, profile s

26、pecific ICS, information object ICS, etc. ICS proforma: document, in the form of a questionnaire, which when completed for an implementation or system becomes an ICS Protocol ICS (PICS): ICS for an implementation or system claimed to conform to a given protocol specification 3.2 Abbreviations For th

27、e purposes of the present document, the following abbreviations apply: BS Base Station CC Channel Code CCL Call Control Layer dPMRTMdigital Private Mobile Radio FDMA Frequency Division Multiple Access ICS Implementation Conformance Statement IP Internet ProtocolIUT Implementation Under Test M1 Mode

28、1 MS M2 Mode 2 MS M3 Mode 3 MS MS Mobile StationOACSU Off-Air Call Set-up PDU Protocol Data Unit PICS Protocol Implementation Conformance Statement PTT Push To Talk SCS System Conformance Statement SUT System Under Test 4 Conformance to this PICS proforma specification If it claims to conform to the

29、 present document, the actual PICS proforma to be filled in by a supplier shall be technically equivalent to the text of the PICS proforma given in annex A, and shall preserve the numbering/naming and ordering of the proforma items. A PICS, which conforms to the present document, shall be a conformi

30、ng PICS proforma completed in accordance with the guidance for completion given in clause A.1. ETSI ETSI TS 102 726-1 V2.2.1 (2014-09)7Annex A (normative): Protocol ICS proforma for TS 102 658 Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI gr

31、ants that users of the present document may freely reproduce the PICS proforma in this annex so that it can be used for its intended purposes and may further publish the completed PICS. A.1 Guidance for completing the PICS proforma A.1.1 Purposes and structure The purpose of this PICS proforma is to

32、 provide a mechanism whereby a supplier of an implementation of the requirements defined in TS 102 658 1, may provide information about the implementation in a standardized manner. The PICS proforma is subdivided into clauses for the following categories of information: guidance for completing the P

33、ICS proforma; identification of the implementation; identification of the TS 102 658 1; global statement of conformance; entity; type M1, M2, M3, BS2, BS3; MS features: - capabilities; - frames; - timers. A.1.2 Abbreviations and conventions The PICS proforma contained in this annex is comprised of i

34、nformation in tabular form in accordance with the guidelines presented in ISO/IEC 9646-7 3. Item column The item column contains a number which identifies the item in the table. Item description column The item description column describes in free text each respective item (e.g. parameters, timers,

35、etc.). It implicitly means “is supported by the implementation?“. ETSI ETSI TS 102 726-1 V2.2.1 (2014-09)8Status column The following notations, defined in ISO/IEC 9646-7 3, are used for the status column: m mandatory - the capability is required to be supported. o optional - the capability may be s

36、upported or not. n/a not applicable - in the given context, it is impossible to use the capability. x prohibited (excluded) - there is a requirement not to use this capability in the given context. o.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer wh

37、ich identifies a unique group of related optional items and the logic of their selection which is defined immediately following the table. ci conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer iden

38、tifying a unique conditional status expression which is defined immediately following the table. i irrelevant (out-of-scope) - capability outside the scope of the reference specification. No answer is requested from the supplier. NOTE 1: This use of “i“ status is not to be confused with the suffix “

39、i“ to the “o“ and “c“ statuses above. Reference column The reference column makes reference to TS 102 658 1, except where explicitly stated otherwise. Support column The support column shall be filled in by the supplier of the implementation. The following common notations, defined in ISO/IEC 9646-7

40、 3, are used for the support column: Y or y supported by the implementation. N or n not supported by the implementation. N/A, n/a or - no answer required (allowed only if the status is n/a, directly or after evaluation of a conditional status). If this PICS proforma is completed in order to describe

41、 a multiple-profile support in a system, it is necessary to be able to answer that a capability is supported for one profile and not supported for another. In that case, the supplier shall enter the unique reference to a conditional expression, preceded by “?“ (e.g. ?3). This expression shall be giv

42、en in the space for comments provided at the bottom of the table. It uses predicates defined in the SCS, each of which refers to a single profile and which takes the value TRUE if and only if that profile is to be used. EXAMPLE 1: ?3: IF prof1 THEN Y ELSE N. NOTE 2: As stated in ISO/IEC 9646-7 3, su

43、pport for a received PDU requires the ability to parse all valid parameters of that PDU. Supporting a PDU while having no ability to parse a valid parameter is non-conformant. Support for a parameter on a PDU means that the semantics of that parameter are supported. ETSI ETSI TS 102 726-1 V2.2.1 (20

44、14-09)9Values allowed column The values allowed column contains the type, the list, the range or the length of values allowed. The following notations are used: range of values: example: 5 20 list of values: , , ., example: 2, 4, 6, 8, 9 example: 1101B, 1011B, 1111B example: 0AH, 34H, 2FH list of na

45、med values: (), (), ., () example: reject(1), accept(2) length: size ( ) example: size (1 8) Values supported column The values supported column shall be filled in by the supplier of the implementation. In this column, the values or the ranges of values supported by the implementation shall be indic

46、ated. References to items For each possible item answer (answer in the support column) within the PICS proforma a unique reference exists, used, for example, in the conditional expressions. It is defined as the table identifier, followed by a solidus character “/“, followed by the item number in the

47、 table. If there is more than one support column in a table, the columns are discriminated by letters (a, b, etc.), respectively. EXAMPLE 2: A.5/4 is the reference to the answer of item 4 in table A.5. EXAMPLE 3: A.6/3b is the reference to the second answer (i.e. in the second support column) of ite

48、m 3 in table A.6 of annex A. Prerequisite line A prerequisite line takes the form: Prerequisite: . A prerequisite line after a clause or table title indicates that the whole clause or the whole table is not required to be completed if the predicate is FALSE. A.1.3 Instructions for completing the PIC

49、S proforma The supplier of the implementation shall complete the PICS proforma in each of the spaces provided. In particular, an explicit answer shall be entered, in each of the support or supported column boxes provided, using the notation described in clause A.1.2. However, the tables containing in “M1“ clause shall only be completed for Mode 1 implementations, and the tables containing in “BS2“ clause shall only be completed for Mode 2 BS implementations, etc. If necessary, the supplier may provide addit