ETSI TS 102 587-3-2007 Electromagnetic compatibility and Radio spectrum Matters (ERM) Peer-to-Peer Digital Private Mobile Radio Part 3 Requirements catalogue《电磁兼容性和无线频谱事务(ERM) 对等数字.pdf

《ETSI TS 102 587-3-2007 Electromagnetic compatibility and Radio spectrum Matters (ERM) Peer-to-Peer Digital Private Mobile Radio Part 3 Requirements catalogue《电磁兼容性和无线频谱事务(ERM) 对等数字.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 102 587-3-2007 Electromagnetic compatibility and Radio spectrum Matters (ERM) Peer-to-Peer Digital Private Mobile Radio Part 3 Requirements catalogue《电磁兼容性和无线频谱事务(ERM) 对等数字.pdf（86页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 102 587-3 V1.1.1 (2007-04)Technical Specification Electromagnetic compatibility andRadio spectrum Matters (ERM);Peer-to-Peer Digital Private Mobile Radio;Part 3: Requirements catalogueETSI ETSI TS 102 587-3 V1.1.1 (2007-04) 2 Reference DTS/ERM-TGDMR-066-3 Keywords digital, mobile, private,

2、radio ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document

3、 can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute,

4、the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI d

5、ocuments is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written

6、permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2007. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Tr

7、ade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 102 587-3 V1.1.1 (2007-04) 3 Contents Intellectual Property Rights4 Foreword.4 1 Scope 5 2 Refer

8、ences 5 3 Definitions and abbreviations.5 3.1 Definitions5 3.2 Abbreviations .6 4 Requirements Catalogue.6 4.1 dPMR common requirements.6 4.1.1 All Call .6 4.1.2 Channel Access.7 4.1.3 Framing.12 4.1.3.1 End Frame.16 4.1.3.2 Header Frames 21 4.1.3.2.1 Call Information Field .29 4.1.3.3 Packet Data F

9、rame 33 4.1.3.4 Superframe37 4.1.3.4.1 Type 1 Data .40 4.1.3.4.2 Type 2 Data .45 4.1.3.4.3 Voice .52 4.1.4 Late Entry .56 4.1.5 Powersave.56 4.1.6 Talking Party Indentification 59 4.2 Configured Services and Facilities Radios.59 4.2.1 Broadcast Call.59 4.2.2 Dialling Plan .60 4.2.3 Individual Short

10、Data78 4.2.3.1 ISDM Free Text Message .78 4.2.3.2 ISDM Precoded Message78 4.2.3.3 ISDM Short File Transfer .79 4.2.3.4 ISDM Status Message .80 4.2.4 Off Air Call Set-up .80 4.2.5 Short Appended Data81 4.2.6 Slow User Data .82 4.2.7 Type 3 Data.83 4.3 Initial Services and Facilities Radios .85 Histor

11、y 86 ETSI ETSI TS 102 587-3 V1.1.1 (2007-04) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be f

12、ound in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to

13、 the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document.

14、Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document is part 3 of a multi-part deliverable covering the Electromagnetic compatibility and Radio spectrum Matters (ERM); Conformance

15、 testing for the Peer-to-Peer Digital Private Mobile Radio, as identified below: Part 1: “Protocol Implementation Conformance Statement (PICS) proforma“; Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “Requirements catalogue“; Part 4: “Abstract Test Suite (ATS)“; Part 5: “Interoperabil

16、ity Test Suite Structure and Test Purposes (TSS Peer-to-Peer Digital Private Mobile Radio using FDMA with a channel spacing of 6,25 kHz with e.r.p. of up to 500 mW“. 2 ETSI TS 102 351: “Methods for Testing and Specification (MTS); Internet Protocol Testing (IPT); IPv6 Testing: Methodology and Framew

17、ork“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: conditionally mandatory: requirement that shall be supported by a standard conformant equipment if and only if the condition(s) stated within its requirement tex

18、t are met NOTE: If one of these conditions is not met the requirement is considered to be not applicable. EXAMPLE: Such a condition may be the support of an optional higher level requirement by the equipment. conditionally optional: requirement that may be supported by a standard conformant equipmen

19、t if and only if the condition(s) stated within its requirement text are met NOTE: If one of these conditions is not met the requirement is considered to be not applicable. mandatory: requirement that shall be supported by a standard conformant equipment optional: requirement that may be supported b

20、y a standard conformant equipment not applicable: requirement that does not have to be met by a standard conformant equipment ETSI ETSI TS 102 587-3 V1.1.1 (2007-04) 6 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: ACK ACKnowledgment AI Air Interface A

21、RQ Automatic Retransmission reQuest CC Colour Code CCH Control CHannel CI Call Information Cont Continuation flagCRC Cyclic Redundancy Checksum for data error detection CSF Configured Services and Facilities Di-bit 2 bits grouped together to represent a 4-level symbol DP Data Position ET End Type FD

22、MA Frequency Division Multiple Access FEC Forward Error Correction FN Frame Numbering HI Header Information HT Header Type ID IDentifier ISF Initial Services and Facilities MFID Manufacturers FID MS Mobile StationNACK Negative ACKnowledgment OACSU Off Air Call Set Up PAR PARameter dataPDF Packet Dat

23、a Format RF Radio Frequency RSSI Received Signal Strength Indication SLD SLow Data SYNC SYNChronization TCH Traffic CHannel4 Requirements Catalogue 4.1 dPMR common requirements 4.1.1 All Call RQ_001_0824 All Call: TS 102 490 1 Clause 8.1.1.1, paragraph 3 Type: Mandatory Applies to: ISF Requirement:

24、A dPMR radio shall support voice group “All call“ supplementary service. Specification Text: All radios will decode an All call (common ID = 255) irrespective of the common ID selected by the user. However, radios that have 255 selected as the common ID will only respond to calls addressed to a comm

25、on ID of 255. Family: RQ_001_0804, RQ_001_0824, RQ_001_0858 Test Purposes: None ETSI ETSI TS 102 587-3 V1.1.1 (2007-04) 7 RQ_001_0858 All Call: TS 102 490 1 Clause 8.1.1.1, paragraph 3 Type: Conditionally Mandatory Applies to: ISF Requirement: IF an ISF radio Common ID is set to 255 THEN the radio s

26、hall only respond to call addressed to Common ID of 255. Specification Text: All radios will decode an All call (common ID = 255) irrespective of the common ID selected by the user. However, radios that have 255 selected as the common ID will only respond to calls addressed to a common ID of 255. Fa

27、mily: RQ_001_0804, RQ_001_0824, RQ_001_0858 Test Purposes: None 4.1.2 Channel Access RQ_001_1001 Channel Access: TS 102 490 1 Clause 10.1, paragraph 2 Type: Mandatory Applies to: ISF, CSF Requirement: A caller radio shall listen before transmit. When the received signal level has not exceeded -105 d

28、Bm for the duration of the T_ch_chk timer then the radio shall assume the channel to be free. Specification Text: When determining whether activity is present on a channel, the radio shall monitor the RSSI level. If after a maximum period of time (T_ch_chk) the RSSI level has not exceeded a configur

29、able (within a predefined range) threshold RSSI_LO, then the radio shall assume that activity is not present on the channel. RSSI_LO shall be set to -105 dBm 3 dB. Family: No Duplicates Test Purposes: None RQ_001_1002 Channel Access: TS 102 490 1 Clause 10.1, paragraph 5 Type: Conditionally Mandator

30、y Applies to: ISF, CSF Requirement: A radio shall listen before transmitting. IF the received signal level is equal or above -105 dBm AND the radio can synchronize on the channel. THEN the radio shall assume that there is dPMR activity on the channel. Specification Text: If however the RSSI level do

31、es exceed this threshold, then the radio shall assume that activity is present on the channel and it shall attempt to become frame synchronized to the activity. If the radio is successful in becoming frame synchronized to the activity, then the radio shall assume that 6,25 kHz FDMA activity is prese

32、nt on the channel. Family: No Duplicates Test Purposes: None ETSI ETSI TS 102 587-3 V1.1.1 (2007-04) 8 RQ_001_1003 Channel Access: TS 102 490 1 Clause 10.1, paragraph 5 Type: Conditionally Mandatory Applies to: ISF, CSF Requirement: A radio shall listen before transmitting. IF the received signal le

33、vel is above -105 dBm AND the radio can not synchronize to the channel for the duration of the T_ch_free timer THEN it shall assume the activity is not dPMR. Specification Text: If however the RSSI level does exceed this threshold, then the radio shall assume that activity is present on the channel

34、and it shall attempt to become frame synchronized to the activity. If however after a maximum period of time (T_ch_free), the radio has not become frame synchronized to the activity, then the radio shall assume that the activity is non-6,25 kHz FDMA activity. Family: No Duplicates Test Purposes: Non

35、e RQ_001_1004 Channel Access: TS 102 490 1 Clause 10.1, paragraph 5 Type: Mandatory Applies to: ISF, CSF Requirement: A radio shall listen before transmitting. When the received signal level is above -105 dBm and the radio manages to synchronize to the channel but the color code is incorrect then it

36、 shall assume the activity is interference. Specification Text: If the radio is successful in becoming frame synchronized to the activity, then the radio shall assume that 6,25 kHz FDMA activity is present on the channel. If the Colour Code is different then the radio shall assume that the activity

37、is interference. Family: No Duplicates Test Purposes: None RQ_001_1005 Channel Access: TS 102 490 1 Clause 10.2.2, paragraph 1 Type: Mandatory Applies to: ISF, CSF Requirement: IF a transmitting radio announces a non zero Tx WAIT time then other radios shall not commence any PTT activated transmissi

38、ons during this Tx WAIT period. Specification Text: When a transmitting radio announces a non zero Tx WAIT time then PTT activated transmissions shall not be permitted to start during this Tx WAIT time irrespective of any polite or impolite criteria employed. Family: No Duplicates Test Purposes: Non

39、e ETSI ETSI TS 102 587-3 V1.1.1 (2007-04) 9 RQ_001_1006 Channel Access: TS 102 490 1 Clause 10.3, paragraph Type: Mandatory Applies to: ISF, CSF Requirement: A transmission shall be automatically terminated if it exceeds 180 seconds. The transmission may only be resumed by rekeying the transmitter.

40、Specification Text: dPMR HSs shall have a transmit TimeOut timer which limits the time of a single transmission item. This timer shall be set to the value of 180 seconds whenever the PTT key is pressed and counts down to zero. If the transmit TimeOut timer expires, then all HSs will stop transmittin

41、g immediately and may not re-transmit until PTT has been released and pressed again. Family: No Duplicates Test Purposes: None RQ_001_1007 Channel Access: TS 102 490 1 Clause 10.4.1, paragraph 1 Type: Optional Applies to: CSF Requirement: When an acknowledgement is required in response to a received

42、 call the callee may transmit this acknowledgement irrespective of whether the RF channel is busy during a defined period after the call has been received. Specification Text: Where a radio has been solicited to transmit a response, it may transmit the response within response time T_ack irrespectiv

43、e of whether the channel is “Idle“ or “Busy“. Family: No Duplicates Test Purposes: None RQ_001_1008 Channel Access: TS 102 490 1 Clause 10.4.2, 10.4.3, paragraph 1 Type: Optional Applies to: ISF, CSF Requirement: When a radio is involved in a voice call it may transmit even if another party to the s

44、ame call is transmitting on the RF channel. Specification Text: Additionally, while a radio is partied to a voice call, it may transmit irrespective of whether the channel is “Idle“ or “Busy“ with 6,25 kHz FDMA activity pertaining to the same voice call but may not transmit if a Tx WAIT time has bee

45、n invoked. Family: No Duplicates Test Purposes: None RQ_001_1009 Channel Access: TS 102 490 1 Clause 10.4.2, paragraph 2 Type: Conditionally Mandatory Applies to: ISF Requirement: IF a ISF radio has polite to own Colour Code enabled THEN the radio shall not transmit when the RF channel is occupied b

46、y a transmission using the same Colour Code. Specification Text: Polite to own Colour Code: The radio shall refrain from transmitting on a channel while the channel is “Busy“ with other 6,25 kHz FDMA activity from radios using the same Colour Code. Family: No Duplicates Test Purposes: None ETSI ETSI

47、 TS 102 587-3 V1.1.1 (2007-04) 10RQ_001_1010 Channel Access: TS 102 490 1 Clause 10.4.2, paragraph 3 Type: Conditionally Optional Applies to: ISF Requirement: IF an ISF radio has impolite channel access enabled THEN it may transmit if the RF channel is occupied by any other signal. Specification Tex

48、t: Impolite: The radio shall transmit on a channel regardless of any other activity (either 6,25 kHz FDMA or otherwise) already present on the channel. Family: No Duplicates Test Purposes: None RQ_001_1011 Channel Access: TS 102 490 1 Clause 10.4.3, paragraph 2 Type: Conditionally Mandatory Applies

49、to: CSF Requirement: IF a CSF radio has polite to own Group or Talkgroup enabled THEN the radio shall not transmit while the RF channel is occupied by transmissions by members of its own group or talkgroup. Specification Text: Polite to own Group or Talkgroup: The radio shall refrain from transmitting on a channel while the channel is “Busy“ with other 6,25 kHz FDMA activity from radios within its own group or talkgroup. For all other types of activity already present on the chann