ETSI TS 102 209-2004 Telecommunications and Internet converged Services and Protocols for Advancing Networks (TISPAN) Telecommunication Equipment Identification (V1 2 1)《电信和互联网融合业务.pdf

《ETSI TS 102 209-2004 Telecommunications and Internet converged Services and Protocols for Advancing Networks (TISPAN) Telecommunication Equipment Identification (V1 2 1)《电信和互联网融合业务.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 102 209-2004 Telecommunications and Internet converged Services and Protocols for Advancing Networks (TISPAN) Telecommunication Equipment Identification (V1 2 1)《电信和互联网融合业务.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 102 209 V1.2.1 (2004-02)Technical Specification Telecommunications and Internet converged Services andProtocols for Advancing Networks (TISPAN);Telecommunication Equipment Identification* ETSI ETSI TS 102 209 V1.2.1 (2004-02) 2 Reference RTS/TISPAN - 08005 Keywords ID, management ETSI 650 R

2、oute des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be download

3、ed from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference sh

4、all be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is avai

5、lable at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all

6、media. European Telecommunications Standards Institute 2004. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is

7、 a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 102 209 V1.2.1 (2004-02) 3 Contents Intellectual Property Rights4 Foreword.4 Introduction 4 1 Scope 5 2 References 5 3 Definitions and abbreviations.5 3.1 Definitions5 3.2 Abbreviati

8、ons .8 4 Business role model .9 4.1 Introduction 9 4.2 Composition of the business role model.9 4.2.1 Roles .9 4.2.2 Value chain .9 4.2.3 Actors10 4.2.4 Interfaces.10 4.3 Conclusion: need for uniform Telecommunication Equipment Identification (TEI) .10 5 PNOs processes making use of equipment identi

9、ty information11 5.1 Engineering process .11 5.2 Acquisition process 13 5.3 Inventory management .14 5.4 Provisioning .15 5.5 Operation and Maintenance (O Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest up

10、dates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on t

11、he ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Services and Protocols for Advanced Networks (SPAN). Introduction Public Network Operators (PNOs) and manufacturers use

12、 different ways to name and identify telecommunication equipment. This causes difficulties and inefficiency. Operators have to manage the different formats and contents by which manufacturers identify their product. Operators frequently having to translate these disparate identifiers into internal c

13、odes to feed their internal systems with the information needed. On the other hand, manufacturers are required by some PNOs to deliver their products with the PNOs proprietary codes and different information. Manufacturers have to manage this information. The business needs of the PNOs and the manuf

14、acturers are different but they do share some common needs. This situation can be rationalized by adopting a manageable unique and global method for the identification of telecommunication equipment. This new identity would link the common needs of both PNOs and manufacturers. It should be used by e

15、ach to exchange information within inter-company and intra-company processes and workflows. ETSI ETSI TS 102 209 V1.2.1 (2004-02) 5 1 Scope The present document provides the information for the identification of telecommunication equipment. The present document focuses on both manufacturers and PNOs

16、 needs when exchanging information. This information can be used either externally or internally. Based on an analysis of the results of a survey TR 102 214 2, the present document identifies the data elements which are considered to be necessary and sufficient to identify equipment. In addition to

17、that, the present document provides associated information which is found useful to be exchanged between manufacturers and PNOs. The format of the Equipment Identity is out of scope of the present document. 2 References The following documents contain provisions which, through reference in this text

18、, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenc

19、ed documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ITU-T Recommendation Y.110: “Global Information infrastructure principles and framework architecture“. 2 ETSI TR 102 214: “Services and Protocols for Advanced Netwo

20、rks (SPAN); Result of the PNOs and Equipment Manufacturers questionnaires for identification of Equipment Unit“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: assignable equipment: equipment units can be assigned

21、and/or unassigned (partially or wholly) to any type of service, circuit, trunk, or facility being provided or used by the PNO NOTE: Assignable equipments may have single or multi-assignment capability. Assignable equipment is further defined as a unit of equipment that is an active component or elem

22、ent within the transmission or signalling path of circuits or channels designed through the service provisioning process to provide telecommunications services to the end customers. Assignable equipment includes: square4 All hardwired (fixed) equipment, portable equipment, plug-ins, plug-ons, hardwi

23、red mountings, shelves and/or backplanes that provide telecommunications services (voice, data, image, video, IP, etc.) for sale, resale, or internal use by the PNO; square4 All components used within the transport, transmission, message and signalling paths operated and/or leased by a PNO; square4

24、Any physical or logical telecommunications component that is an inventoried telecommunication item that can be administered by the PNO. ETSI ETSI TS 102 209 V1.2.1 (2004-02) 6 equipment class: grouping of specific equipments that is identified by Globally Generic and Stable Information and for which

25、 a unique Equipment Identity can be assigned equipment supplier: See manufacturer definitions. Equipment Identity (EI): provides information in a uniform, concise and function-oriented format about each equipment unit within its particular network application or environment NOTE: The EIs identify bo

26、th equipment units and equipment mountings and can be used by both PNOs and manufacturers. The EI should be useable in both manual and OSS environments and provide human and machine-readable information. Each Equipment Identity would: square4 Describe a specific combination of “Globally Generic and

27、Stable Information“ for each equipment unit or mounting; square4 Provide or reference equipment with specific equipment attributes, features and technical information. equipment unit: assembly of one or more components that are wired together to provide one or more specific functions within the netw

28、ork NOTE 1: Equipment units can be either assignable or non-assignable and mounted permanently or temporarily on other equipment units. NOTE 2: Plug-ins, plug-ons, cards, modules, selves/magazines/racks are typical equipment units. equipment mounting: used to mount, wire, store, test and activate eq

29、uipment units NOTE 1: In ITU-T Recommendation M.3100 the Equipment Mounting is modelled by Equipment holder type: “The equipment holder type attribute indicates the type of equipment holder using a character string. The possible values for the character string may be bay, shelf, drawer, slot and rac

30、k“. NOTE 2: Equipment mountings can be assignable or non-assignable and mounted permanently or temporarily on or within other equipment units. NOTE 3: Typical equipment mountings are, relay racks, equipment bays, cabinets, magazines, shelves, modules, containers, drawers, etc. Globally Generic and S

31、table Information (GGSI): consists of no less than a specific instance of the manufacturers name and the part number and version number that is permanently assigned to each equipment unit by the manufacturer NOTE 1: This information must be consistently applied by the manufacturer to all equipment u

32、nits prior to shipment and provides a consistent meaning, representation, or description that is generally understood by professional and technical users. NOTE 2: Stable Information is any data value that is consistent (unchanging) across multiple instances of the same element, feature, or item. Sta

33、ble Information will change only when the element, feature, unit or item it represents is physically, electrically, or optically altered, revised, or modified and considered to be reasonably different from the preceding instance. manufacturer, primary: manufacturer of telecommunication equipment tha

34、t is placed on the market NOTE: A primary manufacturer has the responsibility for the equipment when it comes to warranties and repairs. manufacturer, secondary: vendor that re-brands primary manufacturer telecommunication equipment and places it on the market NOTE: A secondary manufacturer takes ov

35、er a primary manufacturers responsibility for warranties and repairs ETSI ETSI TS 102 209 V1.2.1 (2004-02) 7 manufacturer name: name of the business entity that is responsible for the manufacturing and assembly of the equipment unit NOTE: This name is clearly displayed, etched, or marked on each equ

36、ipment unit and is part of the equipment identity regardless of the current status of the manufacturer (renamed, dissolved, acquired, etc.). In some instances, due to acquisitions, the identical equipment part and version number may be produced under multiple manufacturer names. manufacturer Name is

37、 one of the three primary elements needed to develop an Equipment Identity. manufacturer ordering code: arbitrary commercial code developed by manufacturers for PNOs NOTE 1: This code can be used by a PNO to order one equipment type, or multiple groups of equipment types from manufacturers and suppl

38、iers NOTE 2: Manufacturer ordering codes are not marked nor etched on equipment units, nor do they have a one-to-one relationship with manufacturer part numbers manufacturer part number: proprietary character string of information that is assigned to each equipment unit by its manufacturer NOTE 1: p

39、art numbers can be further described as: square4 coding of arbitrary length and format that uniquely identifies a specific equipment unit or equipment mounting; square4 coding that may contain some basic information on the purpose or function of the equipment unit or mounting; square4 coding that is

40、 stamped or etched on each equipment unit or mounting; square4 part numbers normally do not identify which version, issue, or release number was used to manufacture the equipment unit. NOTE 2: A part number is one of the three primary elements needed to develop an Equipment Identity. NOTE 3: A Part

41、numbers are not EAN 13 (code used on the packaging for consumer goods). manufacturer serial number: arbitrary alphanumeric character string using a proprietary format of non-reoccurring data value (changing) that are marked or etched onto each equipment unit or mounting during assembly by the manufa

42、cturer NOTE 1: It is unique within the context of each manufacturer. NOTE 2: It could provide associated information (e.g. manufacturing time) for each equipment unit. Some of the information associated to the serial number changes across multiple instances during the equipment unit life cycle (eg.

43、technical specifications, repair, etc.). manufacturer equipment version: proprietary information that is assigned to each hardware equipment unit during assembly by the manufacturer NOTE: It identifies changes (eg. applied during the assembly and testing of equipment units without significantly alte

44、ring the electrical, optical, external connectivity or physical characteristics) of the manufacturers original equipment unit. Version is one of the three primary elements needed to develop an Equipment Identity. Management Information Base (MIB): software feature embedded within a system by the man

45、ufacturer NOTE It provides specific information in a software format on an equipment unit. The information contained in a MIB is determined by the manufacturer and is retrievable via a management interface. non-assignable equipment: non-assignable equipment supports but does not directly provide (pa

46、rtially or wholly) any type of customer or company service, circuit, trunk, or facility NOTE: Typical non-assignable equipment would be jack panels, fuse equipment. ETSI ETSI TS 102 209 V1.2.1 (2004-02) 8 plug-in: item of electronic equipment that connects its circuit elements to other equipment, af

47、fects the operation of that equipment and is considered to be replaceable or easily removed NOTE 1: In ITU-T Recommendation M.3100, The circuit pack object class is a class of managed objects that represent a plug-in replaceable unit that can be inserted into or removed from the equipment holder of

48、the network element. Examples of plug-in cards include line cards, processors and power supply units. NOTE 2: A plug-in is dependent on another equipment to complete it. A plug-in may connect to other equipment by means of circuit connectors imprinted on the edge of a circuit board that mate to a ch

49、assis backplane connector. plug-on: plug-on equipment plugs onto a “plug-in“ equipment unit and is sometimes referred to as a “daughter board“ or “child board“ NOTE: A plug-on may complete the function of a plug-in or provide additional functions with hardware, software, or both. It is generally marked with and ordered by its own part number. Public Network Operator (PNO): business entity that sells and/or resells telecommunication services to the public or other service providers NOTE: These services can include wireline, wireless, and IP networks that provide