ETSI TS 102 148-1-3-2004 Broadband Radio Access Networks (BRAN) HIPERACCESS Conformance testing for the Packet based Convergence Layer Part 1 Common part Sub-part 3 Abstract Test S_1.pdf

《ETSI TS 102 148-1-3-2004 Broadband Radio Access Networks (BRAN) HIPERACCESS Conformance testing for the Packet based Convergence Layer Part 1 Common part Sub-part 3 Abstract Test S_1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 102 148-1-3-2004 Broadband Radio Access Networks (BRAN) HIPERACCESS Conformance testing for the Packet based Convergence Layer Part 1 Common part Sub-part 3 Abstract Test S_1.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 102 148-1-3 V1.2.1 (2004-04)Technical Specification Broadband Radio Access Networks (BRAN);HIPERACCESS;Conformance testing for the Packet based Convergence Layer;Part 1: Common part;Sub-part 3: Abstract Test Suite (ATS)ETSI ETSI TS 102 148-1-3 V1.2.1 (2004-04) 2 Reference RTS/BRAN-0034T04-1

2、-3R1 Keywords access, ATM, ATS, broadband, hiperaccess, radio, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7

3、803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference ve

4、rsion is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of s

5、tatus. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notification No part may be reproduced except as authorized by written permi

6、ssion. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2004. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade M

7、arks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 102 148-1-3 V1.2.1 (2004-04) 3 Contents Intellectual Property Rights6 Foreword.6 1 Scope 7 2 Referenc

8、es 7 3 Definitions and abbreviations.8 3.1 Definitions8 3.2 Abbreviations .8 4 Abstract Test Method (ATM).9 4.1 Test architecture .9 4.2 Test Configurations 10 4.2.1 Test Configurations for AT.10 4.2.2 Test Configurations for AP.10 5 Untestable Test Purposes (TP) .10 6 ATS conventions11 6.1 Naming c

9、onventions.11 6.1.1 Declarations part.11 6.1.1.1 General11 6.1.1.2 Test suite operations definition .11 6.1.1.3 Test suite parameter declarations 11 6.1.1.4 Test case selection expression definition 11 6.1.1.5 Test suite constant declarations.12 6.1.1.6 Test suite variable declarations .12 6.1.1.7 T

10、est case variable declarations12 6.1.1.8 Timer declarations.12 6.1.1.9 ASP type definitions .12 6.1.1.10 PDU type definitions.12 6.1.1.11 CM type definitions.12 6.1.1.12 Alias definitions 13 6.1.2 Constraints part.13 6.1.2.1 General13 6.1.3 Dynamic part 13 6.1.3.1 General13 6.1.3.2 Test Case (TC) id

11、entifier.13 6.1.3.3 Test step identifier.13 6.1.3.4 Default identifier .13 6.1.3.5 Label identifier14 6.1.3.6 ATS abbreviations.14 6.2 Implementation conventions 14 6.2.1 Declaration part 14 6.2.2 Constraint part 15 6.2.3 Dynamic part 15 7 Abstract testing service primitives .15 7.1 Tester primitive

12、s.15 7.2 C-plane primitives 15 7.3 U-plane primitives15 Annex A (normative): Abstract Test Suite (ATS) .16 A.1 The TTCN Graphical form (TTCN.GR) 16 A.2 The TTCN Machine Processable form (TTCN.MP)16 Annex B (normative): Partial PIXIT proforma for HIPERACCESS Common part CL AT.17 ETSI ETSI TS 102 148-

13、1-3 V1.2.1 (2004-04) 4 B.1 Identification summary.17 B.2 ATS summary 17 B.3 Test laboratory17 B.4 Client identification18 B.5 SUT 18 B.6 Protocol layer information18 B.6.1 Protocol identification 18 B.6.2 IUT information .19 Annex C (normative): Partial PIXIT proforma for HIPERACCESS Common part CL

14、AP.26 C.1 Identification summary.26 C.2 ATS summary 26 C.3 Test laboratory26 C.4 Client identification27 C.5 SUT 27 C.6 Protocol layer information27 C.6.1 Protocol identification 27 C.6.2 IUT information .28 Annex D (normative): PCTR Proforma for HIPERACCESS Common part CL AT .35 D.1 Identification

15、summary.35 D.1.1 Protocol conformance test report35 D.1.2 IUT identification.35 D.1.3 Testing environment.35 D.1.4 Limits and reservation36 D.1.5 Comments.36 D.2 IUT Conformance status 36 D.3 Static conformance summary .36 D.4 Dynamic conformance summary36 D.5 Static conformance review report.37 D.6

16、 Test campaign report37 D.7 Observations.37 Annex E (normative): PCTR Proforma for HIPERACCESS Common part CL AP38 E.1 Identification summary.38 E.1.1 Protocol conformance test report38 E.1.2 IUT identification.38 E.1.3 Testing environment.38 E.1.4 Limits and reservation39 E.1.5 Comments.39 E.2 IUT

17、Conformance status 39 E.3 Static conformance summary .39 E.4 Dynamic conformance summary39 E.5 Static conformance review report.40 E.6 Test campaign report40 E.7 Observations.40 ETSI ETSI TS 102 148-1-3 V1.2.1 (2004-04) 5 Annex F (informative): Bibliography.41 History 42 ETSI ETSI TS 102 148-1-3 V1.

18、2.1 (2004-04) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intel

19、lectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no invest

20、igation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specifi

21、cation (TS) has been produced by ETSI Project Broadband Radio Access Networks (BRAN). The present document is part 1, sub-part 3 of a multi-part covering testing specification for the Packet based Convergence Layer of the BRAN HIPERACCESS system, as identified below: Part 1: “Common part“; Sub-part

22、1: “Protocol Implementation Conformance Statement (PICS) proforma“; Sub-part 2: “Test Suite Structure and Test Purposes (TSS Sub-part 3: “Abstract Test Suite (ATS)“. Part 2: “Ethernet Service Specific Convergence Sublayer (SSCS)“. ETSI ETSI TS 102 148-1-3 V1.2.1 (2004-04) 7 1 Scope The present docum

23、ent contains the Abstract Test Suite (ATS) to test the TS 102 117-1 1. The objective of the present document is to provide a basis for conformance tests for BRAN HIPERACCESS equipment giving a high probability of air interface inter-operability between different manufacturers BRAN HIPERACCESS equipm

24、ent. The ISO standard for the methodology of conformance testing (ISO/IEC 9646-1 4 and ISO/IEC 9646-2 5) as well as the ETSI rules for conformance testing (ETS 300 406 3) are used as a basis for the test methodology. - Annex A provides the Tree and Tabular Combined Notation (TTCN) part of the ATS. -

25、 Annex B provides the Partial Protocol Implementation Extra Information for Testing (PIXIT) Proforma of the AT side ATS. - Annex C provides the Partial Protocol Implementation Extra Information for Testing (PIXIT) Proforma of the AP side ATS. - Annex D provides the Protocol Conformance Test Report (

26、PCTR) Proforma of the AT side ATS. - Annex E provides the Protocol Conformance Test Report (PCTR) Proforma of the AP side ATS. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific

27、(identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected locati

28、on might be found at http:/docbox.etsi.org/Reference. 1 ETSI TS 102 117-1: “Broadband Radio Access Networks (BRAN); HIPERACCESS; Packet based Convergence Layer; Part 1: Common Part“. 2 ETSI TS 102 149-3 (V1.2.1): “Broadband Radio Access Networks (BRAN); HIPERACCESS; Conformance Testing for the Data

29、Link Control (DLC) layer; Sub-part 3: Abstract Test Suite (ATS) specification“. 3 ETSI ETS 300 406: “Methods for Testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. 4 ISO/IEC 9646-1: “Information technology - Open Systems Interconne

30、ction - Conformance testing methodology and framework - Part 1: General concepts“. 5 ISO/IEC 9646-2: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 2: Abstract test suite specification“. 6 ISO/IEC 9646-3 (1991): “Information technology -

31、 Open Systems Interconnection - Conformance testing methodology and framework - Part 3: The tree and tabular combined notation“. 7 ISO/IEC 9646-6: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 6: Protocol profile test specification“. 8

32、ISO/IEC 9646-7: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation conformance statement“. ETSI ETSI TS 102 148-1-3 V1.2.1 (2004-04) 8 9 ETSI TS 102 148-1-2: “ Broadband Radio Access Networks (BRAN); HIPERACCESS; Conformanc

33、e testing for the Packet based Convergence Layer; Part 1: Common part; Sub-part 2: Test Suite Structure and Test Purposes (TSS - The minimum value allowed, which will use the suffix “_min“; - The value actually implemented, with no suffix; EXAMPLE 1: T201_max, T201_min, and T201. 2) Not standardised

34、: - Those not defined in the protocol standard, i.e. for execution use, e.g. a timer waiting for a response. These timers begin with the prefix “T_“, followed by a string in lowercase letters. EXAMPLE 2: T_resp represents a timer for controlling the response time of the IUT. 6.1.1.9 ASP type definit

35、ions The general conventions in clause 6.1.1.1 apply. The identifier of an ASP type uses the same name as the name defined in the protocol standard. 6.1.1.10 PDU type definitions The general conventions in clause 6.1.1.1 apply. The PDU type identifier shall identify the related structure or type as

36、defined in the protocol standard. 6.1.1.11 CM type definitions The CM types are defined as the ASP types without sub-fields. ETSI ETSI TS 102 148-1-3 V1.2.1 (2004-04) 136.1.1.12 Alias definitions Alias definitions are not used. 6.1.2 Constraints part This clause describes the naming conventions chos

37、en for the elements of the ATS constraints part. 6.1.2.1 General Constraints shall be written with the first letter in uppercase, and the rest in lowercase. The first part of the constraint declaration identifier name is equivalent to the corresponding type identifier used in the declaration part. T

38、he second part of the name describes the content of this constraint. EXAMPLE: Declaration part: HEADER_FIELD. Constraint part: Header_field_paging. 6.1.3 Dynamic part This clause describes the naming conventions used for the elements of the ATS dynamic part. 6.1.3.1 General All test cases shall be l

39、isted in the order in which they appear in the Test Suite Structure (TSS) and TP document. 6.1.3.2 Test Case (TC) identifier The identifier of the test case is built in the same way as for the test purpose described in TS 102 148-1-2 9, with the exception that “TP“ is replaced by “TC“. The identifie

40、r of a TC is built according to table 2. Table 2: TC naming convention Identifier: TC_ = side type AP Access Point AT Access Terminal = protocole group CPP Common Part Procedures = functional module SS Sender Side RS Receiver Side x = Type of testing CA CApability tests BV Valid Behaviour tests BI I

41、nvalid Behaviour tests BO Inoportune Behaviour tests = sequential number (000-999) Test Purpose number EXAMPLE: TP identifier: TP/AT/CPP/RS/BV-010. TC identifier: TC_AT_CPP_RS_BV_010. 6.1.3.3 Test step identifier The test step identifier is built of substrings in lowercase letters, preceded by a str

42、ing of uppercase letters. Underscore characters join the substrings. The first substring indicates the main function of the test step; e.g. PR for preamble, PO for postamble, Local Tree (LTS) for local tree and general test STeP (STP) for general test step. The second substring indicates the purpose

43、 of the step. EXAMPLE: PO_release_duc 6.1.3.4 Default identifier The default identifiers begin with the prefix “DF_“, followed by a string in lowercase letters. ETSI ETSI TS 102 148-1-3 V1.2.1 (2004-04) 146.1.3.5 Label identifier The identifiers in the label column is built according to table 3: Tab

44、le 3: Naming convention for verdict assignment identifier Identifier: = type of table TB Test Body CS Check State test step DF DeFault PO POstamble PR PReamblTS TestStep = sequential number (00-99) Label number 6.1.3.6 ATS abbreviations These abbreviations are used to shorten identifier names: addr

45、address ack acknowledgement bear bearer cap capability cfm confirmchn channel con connection ctrl control est establish ext extensionid identification ind indicationinfo information max maximum min minimum par parameter prop proprietary rel release req request rsp responsestd standard sys system6.2

46、Implementation conventions 6.2.1 Declaration part The comment line of single element TTCN tables (e.g. test suite constants) is used to give a reference where the format and content of the element is described in the relevant protocol standards. Any particularity of the element format or content is

47、described in the comment line. The comment line in the header of multi element TTCN tables (e.g. ASP) is used to reference to the protocol standard. The detailed comments are used to describe any particularity of the table. In the ASP and PDU declarations the comment column is further used to give i

48、nformation about the parameter/field value, in particular if the parameter/field contains a fixed spare value. ETSI ETSI TS 102 148-1-3 V1.2.1 (2004-04) 156.2.2 Constraint part The ASPs and PDUs are defined in a way that all relevant parameters/fields are parameterized. That improves the transparenc

49、y of the constraints in the dynamic part, as all values, which are relevant for the test, are always present. Generally no modified constraints are used. This allows an easier reuse and adaptation of constraints if they are reused in other test specifications. The Comment line of a constraint always contains a reference to the relevant protocol standard. The detailed comment footer is used to describe any particularity of the table. 6.2.3 Dynamic part All events which are defined as a conformance requirement by the TP, causes a prelimi