ETSI TS 101 823-3-1-2004 Broadband Radio Access Networks (BRAN) HIPERLAN Type 2 Conformance testing for the Data Link Control (DLC) layer Part 3 Profile for business environment Su_1.pdf

《ETSI TS 101 823-3-1-2004 Broadband Radio Access Networks (BRAN) HIPERLAN Type 2 Conformance testing for the Data Link Control (DLC) layer Part 3 Profile for business environment Su_1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 101 823-3-1-2004 Broadband Radio Access Networks (BRAN) HIPERLAN Type 2 Conformance testing for the Data Link Control (DLC) layer Part 3 Profile for business environment Su_1.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 101 823-3-1 V1.3.1 (2004-08)Technical Specification Broadband Radio Access Networks (BRAN);HIPERLAN Type 2;Conformance testing for the Data Link Control (DLC) layer;Part 3: Profile for business environment;Sub-part 1: Profile Requirement List (PRL) proforma ETSI ETSI TS 101 823-3-1 V1.3.1 (

2、2004-08) 2 Reference RTS/BRAN-002T0B4-3-1 Keywords access, HIPERLAN, PICS, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Gra

3、sse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the

4、reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or

5、 change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notification No part may be reproduced except as authorized by w

6、ritten permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2004. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo

7、 are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 101 823-3-1 V1.3.1 (2004-08) 3 Contents Intellectual Property Rights4 Foreword.4 Introduc

8、tion 4 1 Scope 5 2 References 5 3 Definitions and abbreviations.6 3.1 Definitions6 3.2 Abbreviations .6 4 Conformance to this PRL proforma specification6 Annex A (normative): Profile specific ICS proforma for TS 101 761-37 A.1 Guidance for completing the proforma 7 A.1.1 Purposes and structure7 A.1.

9、2 Abbreviations and conventions 7 A.1.3 Instructions for completing the PICS proforma9 A.2 Identification of the implementation 9 A.2.1 Date of the statement10 A.2.2 Implementation Under Test (IUT) identification .10 A.2.3 System Under Test (SUT) identification10 A.2.4 Product supplier10 A.2.5 Clien

10、t (if different from product supplier)11 A.2.6 PICS contact person .11 A.3 Identification of TS 101 761-3 .12 A.4 Global statement of conformance.12 A.5 Profile specific ICS proforma.12 Annex B (normative): Profile requirement list .13 B.1 Purpose and structure .13 B.2 DLC - Error Control protocol.1

11、3 B.2.1 Major capabilities.13 B.2.2 Repetition mode - receiver capabilities 13 B.3 Radio Link Control (RLC) protocol.13 B.3.1 MT implementation14 B.3.1.1 Association function .14 B.3.1.2 Broadcast and multicast function14 B.3.1.3 Handover function 14 B.3.2 AP implementation.15 B.3.2.1 Association fu

12、nction .15 B.3.2.2 Broadcast and multicast function15 B.3.2.3 Handover function 16 B.4 Convergence layer protocols16 Annex C (informative): Bibliography.17 History 18 ETSI ETSI TS 101 823-3-1 V1.3.1 (2004-08) 4 Intellectual Property Rights IPRs essential or potentially essential to the present docum

13、ent may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of

14、ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existe

15、nce of other IPRs not referenced in SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Project Broadband Radio Access Networks (BRAN). The present document is

16、part 3, sub-part 1 of a multi-part deliverable. Full details of the entire series can be found in part 1, sub-part 1 5. Introduction To evaluate conformance of a particular implementation, it is necessary to have a statement of which capabilities and options have been implemented for a telecommunica

17、tion specification. When such a statement is based on a profile, it is called Profile Requirement List (PRL). ETSI ETSI TS 101 823-3-1 V1.3.1 (2004-08) 5 1 Scope The present document provides the Profile Requirement List (PRL) proforma for BRAN HIPERLAN type 2 DLC layer, Profile for business environ

18、ments as defined in TS 101 761-3 1 in compliance with the relevant requirements and in accordance with the relevant guidance given in ISO/IEC 9646-7 4 and ETS 300 406 2. It details in tabular form the implementation options, i.e. the optional functions additional to those which are mandatory to impl

19、ement. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, s

20、ubsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ETSI TS 101 761-3 (V1.2.1): “Broadband Radio Access Networks (BR

21、AN); HIPERLAN Type 2; Data Link Control (DLC) Layer; Part 3: Profile for Business Environment“. 2 ETSI ETS 300 406 (1995): “Methods for testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. 3 ISO/IEC 9646-1: “Information technology -

22、Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 4 ISO/IEC 9646-7: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 5 ETSI TS 101 823-1-1:

23、“Broadband Radio Access Networks (BRAN); HIPERLAN Type 2; Conformance testing for the Data Link Control (DLC) layer; Part 1: Basic data transport functions; Sub-part 1: Protocol Implementation Conformance Statement (PICS) proforma“. 6 ETSI TS 101 823-2-1: “Broadband Radio Access Networks (BRAN); HIP

24、ERLAN Type 2; Conformance testing for the Data Link Control (DLC) layer; Part 2: Radio Link Control (RLC) sublayer; Sub-part 1: Protocol Implementation Conformance Statement (PICS) proforma“. 7 Void. 8 ETSI TS 101 811-1-1: “Broadband Radio Access Networks (BRAN); HIPERLAN Type 2; Conformance testing

25、 for the packet based convergence layer; Part 1: Common part; Sub-part 1: Protocol Implementation Conformance Statement (PICS) proforma“. 9 ETSI TS 101 811-2-1: “Broadband Radio Access Networks (BRAN); HIPERLAN Type 2; Conformance testing for the packet based convergence layer; Part 2: Ethernet Serv

26、ice Specific Convergence Sublayer (SSCS); Sub-part 1: Protocol Implementation Conformance Statement (PICS) proforma“. ETSI ETSI TS 101 823-3-1 V1.3.1 (2004-08) 6 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in TS 101 761-3

27、1, ISO/IEC 9646-1 3, ISO/IEC 9646-7 4 and the following apply: Implementation Conformance Statement (ICS): statement made by the supplier of an implementation or system claimed to conform to a given specification, stating which capabilities have been implemented NOTE: The ICS can take several forms:

28、 protocol ICS, profile ICS, profile specific ICS, information object ICS, etc. ICS proforma: document, in the form of a questionnaire, which when completed for an implementation or system becomes an ICS Protocol ICS (PICS): ICS for an implementation or system claimed to conform to a given protocol s

29、pecification Profile Requirement List (PRL): Requirement list for an implementation or system claimed to conform to a given profile specification 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: ACF Association Control Function AP Access Point DLC Data L

30、ink Control ICS Implementation Conformance Statement IUT Implementation Under Test MT Mobile Terminal PDU Protocol Data Unit PICS Protocol Implementation Conformance Statement PRL Profile Requirement List RLC Radio Link Control SUT System Under Test 4 Conformance to this PRL proforma specification I

31、f it claims to conform to the present document, the actual PICS proformas to be filled in by a supplier shall be technically equivalent to the text of the PICS proformas given in reference and shall preserve the numbering/naming and ordering of the proforma it. In addition, the profile specific ICS

32、of annex A and the PRL of annex B to be filled in by a supplier shall be technically equivalent to the text of these proformas. A PICS which conforms to the present document shall be a conforming PICS proforma completed in accordance with the guidance for completion given in clause A.1. ETSI ETSI TS

33、 101 823-3-1 V1.3.1 (2004-08) 7 Annex A (normative): Profile specific ICS proforma for TS 101 761-3 This annex contains the Profile specific ICS proforma covering the parts of the protocols which are not covered by the individual PICS on which the profile is based. This Profile specific ICS proforma

34、 may be empty if no additional capabilities are required. In addition, this annex provides instructions to handle the individual PICS. Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may freely reprodu

35、ce the PICS proforma in this annex so that it can be used for its intended purposes and may further publish the completed PICS. A.1 Guidance for completing the proforma A.1.1 Purposes and structure The purpose of this PICS proforma is to provide a mechanism whereby a supplier of an implementation of

36、 the requirements defined in TS 101 761-3 1 may provide information about the implementation in a standardized manner. The PICS proforma is subdivided into clauses for the following categories of information: - guidance for completing the PICS proforma; - identification of the implementation; - iden

37、tification of TS 101 761-3; - global statement of conformance; - roles; - major capabilities; - PDUs; - PDU parameters. A.1.2 Abbreviations and conventions The PICS proforma contained in this annex is comprised of information in tabular form in accordance with the guidelines presented in ISO/IEC 964

38、6-7 4. Item column The item column contains a number which identifies the item in the table. Item description column The item description column describes in free text each respective item (e.g. parameters, timers, etc.). It implicitly means “is supported by the implementation?“. ETSI ETSI TS 101 82

39、3-3-1 V1.3.1 (2004-08) 8 Status column The following notations, defined in ISO/IEC 9646-7 4, are used for the status column: m mandatory - the capability is required to be supported. o optional - the capability may be supported or not. n/a not applicable - in the given context, it is impossible to u

40、se the capability. x prohibited (excluded) - there is a requirement not to use this capability in the given context. o.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies a unique group of related optional items and the logic of their se

41、lection which is defined immediately following the table. ci conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying a unique conditional status expression which is defined immediately follo

42、wing the table. i irrelevant (out-of-scope) - capability outside the scope of the reference specification. No answer is requested from the supplier. NOTE 1: This use of “i“ status is not to be confused with the suffix “i“ to the “o“ and “c“ status above. Reference column The reference column makes r

43、eference to TS 101 761-3, except where explicitly stated otherwise. Support column The support column shall be filled in by the supplier of the implementation. The following common notations, defined in ISO/IEC 9646-7 4, are used for the support column: Y or y supported by the implementation. N or n

44、 not supported by the implementation. N/A, n/a or - no answer required (allowed only if the status is n/a, directly or after evaluation of a conditional status). If this PICS proforma is completed in order to describe a multiple-profile support in a system, it is necessary to be able to answer that

45、a capability is supported for one profile and not supported for another. In that case, the supplier shall enter the unique reference to a conditional expression, preceded by “?“ (e.g. ?3). This expression shall be given in the space for comments provided at the bottom of the table. It uses predicate

46、s defined in the SCS, each of which refers to a single profile and which takes the value TRUE if and only if that profile is to be used. EXAMPLE 1: ?3: IF prof1 THEN Y ELSE N NOTE 2: As stated in ISO/IEC 9646-7 4, support for a received PDU requires the ability to parse all valid parameters of that

47、PDU. Supporting a PDU while having no ability to parse a valid parameter is non-conformant. Support for a parameter on a PDU means that the semantics of that parameter are supported. Values allowed column The values allowed column contains the type, the list, the range, or the length of values allow

48、ed. The following notations are used: - range of values: example: 5 20 ETSI ETSI TS 101 823-3-1 V1.3.1 (2004-08) 9 - list of values: , , ., example: 2 ,4 ,6 ,8, 9 example: 1101B, 1011B, 1111B example: 0AH, 34H, 2FH - list of named values: (), (), ., () example: reject(1), accept(2) - length: size (

49、) example: size (1 8) Values supported column The values supported column shall be filled in by the supplier of the implementation. In this column, the values or the ranges of values supported by the implementation shall be indicated. References to items For each possible item answer (answer in the support column) within the PICS proforma a unique reference exists, used, for example, in the conditional expressions. It is defined as the table identifier, followed by a solidus character “/“, followed by the item number