ETSI TS 101 522-2000 Telecommunications and Internet Protocol Harmonization over Networks (TIPHON) Protocol Implementation Conformance Statement (PICS) Proforma for the Support of .pdf

《ETSI TS 101 522-2000 Telecommunications and Internet Protocol Harmonization over Networks (TIPHON) Protocol Implementation Conformance Statement (PICS) Proforma for the Support of .pdf》由会员分享，可在线阅读，更多相关《ETSI TS 101 522-2000 Telecommunications and Internet Protocol Harmonization over Networks (TIPHON) Protocol Implementation Conformance Statement (PICS) Proforma for the Support of .pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、ETSI TS 101 522 1.1.1 (2000-09) Technical Specification Telecommunications and Internet Protocol Harmonization Over Networks (TI PHON); Protocol Implementation Conformance Statement (PICS) proforma for the support of control protocol for multimedia communication; Support of ITU-T Recommendation H.24

2、5 2 ETSI TS 1 O1 522 V1.l.l (2000-09) The pre Reference DTS/TIPHON-06013 Keywords Voice, IP, supplementary service, VolP, internet, gatekeeper, PICS ETSI 650 Route des Lucioles F-O6921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 O0 Fax: +33 4 93 65 47 16 Siret No 348 623 562 0001 7 - NAF 74

3、2 C Association but non lucratif enregistre la Sous-prfecture de Grasse (06) No 7803/88 Important notice Individual copies of the present document can be downloaded from: http:llwww.etsi.org ent document may be made available in more than one electronic version or in print. In e of existing or perce

4、ived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should b

5、e aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:llwww.etsi.orcg/lb/status/ If you find errors in the present document, send your comment to: editor et.si.fr Copyright Notification No par

6、t may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards Institute 2000. All rights reserved. ETSI 3 ETSI TS 1 O1 522 V1.l.l (2000-09) Contents Intellectual Property Rights

7、 4 Foreword . 4 Introduction 4 1 Scope 5 2 References 5 3 Definitions and abbreviations . 5 3.1 Definitions 5 3.2 Abbreviations . 6 4 Conformance to this PICS proforma specification . 6 Annex A (normative): PICS proforma for ITU-T Recommendation H.245 . 7 A . 1 Guidance for completing the PICS profo

8、rma . 7 A . 1.1 Purposes and structure 7 A . 1.2 Abbreviations and conventions 7 A . 1.3 Instructions for completing the PICS proforma 9 A.2 A.2.1 A.2.2 Implementation Under Test (IUT) identification . 10 A.2.3 System Under Test (SUT) identification 10 A.2.4 Product supplier 10 A.2.5 Client (if diff

9、erent from product supplier) 11 A.2.6 A.3 A.4 AS Identification of the implementation 10 Date of the statement 10 PICS contact person . 11 PICS/System Conformance Statement (SCS) 12 Identification of the protocol 12 Global statement of conformance . 12 A.6 Capabilities . 12 A.6.1 Major capabilities

10、. 12 A.6.2 Subsidiary capabilities 13 A.6.3 Protocol data units 14 A.6.4 Timers 15 A.6.5 Counters . 15 History 16 ETSI 4 ETSI TS 1 O1 522 V1.l.l (2000-09) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pert

11、aining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR O00 3 14: “Intellectual Propero Rights (IPRs); Essential, or potentially Essential, IPRs notifed to ETSI in respect of ETSI standards“, which is available from the ETSI Secreta

12、riat. Latest updates are available on the ETSI Web server (-). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR O00 314 (or the updates on the ETSI Web server

13、) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Project Telecommunications and Internet Protocol Harmonization Over Networks (TIPHON). Introduction To evaluate conformance of a particular implementation, i

14、t is necessary to have a statement of which capabilities and options have been implemented for a telecommunication specification. Such a statement is called an Implementation Conformance Statement (ICs). ETSI 5 ETSI TS 1 O1 522 V1.l.l (2000-09) 1 Scope The present document provides the Protocol Impl

15、ementation Conformance Statement (PICS) proforma for the control protocol for multimedia communication as specified in ITU-T Recommendation H.245 2 in compliance with the relevant requirements and in accordance with the relevant guidance given in ISO/IEC 9646-7 5. The supplier of a protocol implemen

16、tation which is claimed to conform to ITU-T Recommendation H.245 2 is required to complete a copy of the PICS proforma provided in annex A of the present document and is required to provide the information necessary to identify both the supplier and the implementation. 2 References The following doc

17、uments contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a

18、 non-specific reference, the latest version applies. A non-specific reference to an ETS shall also be taken to refer to later versions published as an EN with the same number. il ITU-T Recommendation H.323 (Version 3,1999): “Packet-based multimedia communications systems“. Pl 31 ITU-T Recommendation

19、 H.245: “Control protocol for multimedia communication“. ITU-T Recommendation H.225.0 (Version 3, 1999): “Call signalling protocols and media stream packetization for packet-based multimedia communication systems“. ISO/IEC 9646- 1 (1994): “Information technology - Open Systems Interconnection - Conf

20、ormance testing methodology and framework - Part 1: General concepts“. 41 51 ISO/IEC 9646-7 (1995): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 3 Definitions and abbreviations 3.1 Definitions

21、 For the purposes of the present document, the following terms and definitions apply: terms defined in ITU-T Recommendation H.323 i; terms defined in ITU-T Recommendation H.245 2; terms defined in ISO/IEC 9646-1 4 and in ISO/IEC 9646-7 5. ETSI 6 ETSI TS 1 O1 522 V1.l.l (2000-09) In particular, the f

22、ollowing terms defined in ISO/IEC 9646-1 4 apply: Implementation Conformance Statement (ICs): statement made by the supplier of an implementation or system claimed to conform to a given specification, stating which capabilities have been implemented. The PICS can take several forms: protocol PICS, p

23、rofile PICS, profile specific PICS, information object PICS, etc. ICs proforma: document, in the form of a questionnaire, which when completed for an implementation or system becomes a PICS Protocol ICs (PICS): ICs for an implementation or system claimed to conform to a given protocol specification

24、3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: GK GateKeeper ICs Implementation Conformance Statement IUT Implementation Under Test PDU Protocol Data Unit PICS Protocol Implementation Conformance Statement SCS System Conformance Statement SUT System Un

25、der Test 4 Conformance to this PICS proforma specification If it claims to conform to the present document, the actual PICS proforma to be filled in by a supplier shall be technically equivalent to the text of the PICS proforma given in annex A, and shall preserve the numberinghaming and ordering of

26、 the proforma items. A PICS which conforms to the present document shall be a conforming PICS proforma completed in accordance with the guidance for completion given in clause A. 1. ETSI 7 ETSI TS 1 O1 522 V1.l.l (2000-09) Annex A (normative): PICS proforma for ITU-T Recommendation H.245 Notwithstan

27、ding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may freely reproduce the PICS proforma in this annex so that it can be used for its intended purposes and may further publish the completed PICS. A.l Guidance for c

28、ompleting the PICS proforma A. 1 .I Purposes and structure The purpose of this PICS proforma is to provide a mechanism whereby a supplier of an implementation of the requirements defined in ITU-T Recommendation H.225.0 may provide information about the implementation in a standardized manner. The PI

29、CS proforma is subdivided into subclauses for the following categories of information: - - identification of the implementation; guidance for completing the PICS proforma; - identification of the protocol; - global statement of conformance; - roles; - major capabilities; - subsidiary capabilities; -

30、 operations; - arguments, results and errors; - timers. A. 1.2 Abbreviations and conventions The PICS proforma contained in this annex is comprised of information in tabular form in accordance with the guidelines presented in ISO/IEC 9646-7. Item column The item column contains a number which identi

31、fies the item in the table. Item description column The item description column describes in free text each respective item (for example parameters, timers, etc.). It implicitly means “is supported by the implementation?“. ETSI 8 Status column ETSI TS 1 O1 522 V1.l.l (2000-09) The following notation

32、s, defined in ISO/IEC 9646-7, are used for the status column: m mandatory - the capability is required to be supported; O n/a X 0.i optional - the capability may be supported or not; not applicable - in the given context, it is impossible to use the capability; prohibited (excluded) - there is a req

33、uirement not to use this capability in the given context; qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies a unique group of related optional items and the logic of their selection which is defined immediately following the table; condi

34、tional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying a unique conditional status expression which is defined immediately following the table; ci 1 irrelevant (out-of-scope) - capability outsid

35、e the scope of the reference specification. No answer is requested from the supplier. Reference column The reference column makes reference to ITU-T Recommendation H.225.0 except where explicitly stated otherwise. Support column The support column shall be filled in by the supplier of the implementa

36、tion. The following common notations, defined in ISO/IEC 9646-7, are used for the support column: Y or y N or n N/A, n/a or supported by the implementation; not supported by the implementation; no answer required (allowed only if the status is n/a, directly or after evaluation of a conditional statu

37、s). If this PICS proforma is completed in order to describe a multiple-profile support in a system, it is necessary to be able to answer that a capability is supported for one profile and not supported for another. In that case, the supplier shall enter the unique reference to a conditional expressi

38、on, preceded by “?“ (for example ?3). This expression shall be given in the space for comments provided at the bottom of the table. It uses predicates defined in the SCS, each of which refers to a single profile and which takes the value TRUE if and only if that profile is to be used. EXAMPLE: ?3: I

39、F prof1 THEN Y ELSE N. It is also possible to provide a comment to an answer in the space provided at the bottom of the table. NOTE: As stated in ISO/IEC 9646-7, support for a received PDU requires the ability to parse all valid parameters of that PDU. Supporting a PDU while having no ability to par

40、se a valid parameter is non-conformant. Support for a parameter on a PDU means that the semantics of that parameter are supported. ETSI 9 ETSI TS 1 O1 522 V1.l.l (2000-09) Values allowed column The values allowed column contains the type, the list, the range, or the length of values allowed. The fol

41、lowing notations are used: - range of values: : - example: 5 20. - List of values: , , , : - example: 2,4, 6, 8,9; - example: 1 101B, 101 lB, 1 11 1B; - example: OAH, 34H, 2F“. - List of named values: (), (), , (: - example: reject(l), accept(2). - Length: size ( ): - example: size (i 8). Values sup

42、ported column The values supported column shall be filled in by the supplier of the implementation. In this column, the values or the ranges of values supported by the implementation shall be indicated. References to items For each possible item answer (answer in the support column) within the PICS

43、proforma a unique reference exists, used, for example, in the conditional expressions. It is defined as the table identifier, followed by a solidus character “/“, followed by the item number in the table. If there is more than one support column in a table, the columns are discriminated by letters (

44、a, b, etc.), respectively. EXAMPLE 1: AS4 is the reference to the answer of item 4 in table 5 of annex A. EXAMPLE 2: A.6/3b is the reference to the second answer (Le. in the second support column) of item 3 in table 6 of annex A. Prerequisite line A prerequisite line takes the form: Prerequisite: .

45、A prerequisite line after a clause or table title indicates that the whole clause or the whole table is not required to be completed if the predicate is FALSE. A.1.3 Instructions for completing the PICS proforma The supplier of the implementation shall complete the PICS proforma in each of the space

46、s provided. In particular, an explicit answer shall be entered, in each of the support or supported column boxes provided, using the notation described in subclause A. 1.2. If necessary, the supplier may provide additional comments in space at the bottom of the tables, or separately on sheets of pap

47、er. More detailed instructions are given at the beginning of the different subclauses of the PICS proforma. ETSI 10 ETSI TS 1 O1 522 V1.l.l (2000-09) A.2 Identification of the implementation Identification of the Implementation Under Test (IUT) and the system in which it resides (the System Under Te

48、st (SUT) should be filled in so as to provide as much detail as possible regarding version numbers and configuration options. The product supplier information and client information should both be filled in if they are different. A person who can answer queries regarding information supplied in the

49、PICS should be named as the contact person. A.2.1 Date of the statement . A.2.2 Implementation Under Test (IUT) identification IUT name: . IUT version: A.2.3 System Under Test (SUT) identification SUT name: . Hardware configuration: . . Operating system: A.2.4 Product supplier Name: . Address : . . ETSI 11 ETSI TS 1 O1 522 V1.l.l (2000-09) Telephone number: . Facsimile number: E-mail address: . Additional information: . A.2.5 Client (if different from product supplier) Name: . Address : . Telephone number: . Facsimile number: . E-mail address: Additiona