ETSI TS 100 396-8-4-2000 Terrestrial Trunked Radio (TETRA) Technical Requirements for Direct Mode Operation (DMO) Part 8 Protocol Implementation Conformance Statement (PICS) Profor.pdf

《ETSI TS 100 396-8-4-2000 Terrestrial Trunked Radio (TETRA) Technical Requirements for Direct Mode Operation (DMO) Part 8 Protocol Implementation Conformance Statement (PICS) Profor.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 100 396-8-4-2000 Terrestrial Trunked Radio (TETRA) Technical Requirements for Direct Mode Operation (DMO) Part 8 Protocol Implementation Conformance Statement (PICS) Profor.pdf（45页珍藏版）》请在麦多课文档分享上搜索。

1、ETSI TS 1 O0 396-8-4 1.1.1 (2000-IO) Technical Speci fica tion Terrestrial Trunked Radio (TETRA); Technical requirements for Direct Mode Operation (DMO); Part 8: Protocol Implementation Conformance Statement (PICS) proforma specification; Sub-part 4: Type 2 repeater Air Interface (AI) 2 ETSI TS 1 O0

2、 396-8-4 V1.l.l (2000-1 O) The pre Reference DTSITETRA-02007-8-4 Keywords DMO, ICs, PICS, radio, TETRA ETSI 650 Route des Lucioles F-O6921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 O0 Fax: +33 4 93 65 47 16 Siret No 348 623 562 0001 7 - NAF 742 C Association but non lucratif enregistre la

3、 Sous-prfecture de Grasse (06) No 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.orq ent document may be made available in more than one electronic version or in print. In e of existing or perceived difference in contents between such versio

4、ns, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to rev

5、ision or change of status. Information on the current status of this and other ETSI documents is available at http:/www.etsi.orq/tb/status/ If you find errors in the present document, send your comment to: editor et.si.fr Copyright Notification No part may be reproduced except as authorized by writt

6、en permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards Institute 2000. All rights reserved. ETSI 3 ETSI TS 1 O0 396-8-4 V1.l.l (2000-1 O) Contents Intellectual Property Rights 5 Foreword . 5 Introduction 5 1 Scope 6 2 R

7、eferences 6 3 Definitions and abbreviations . 6 3.1 Definitions 6 3.2 Abbreviations . 7 4 Conformance to this PICS proforma specification . 7 Annex A (normative): Protocol ICs proforma (PICS) for EN 300 396-4 . 8 A . 1 A.l.l A . 1.2 A.1.3 A.2 A.2.1 A.2.2 Implementation Under Test (IUT) identificatio

8、n . 10 A.2.3 System Under Test (SUT) identification 11 A.2.4 Product supplier 11 A.2.5 Client (if different from product supplier) 11 A.2.6 PICS contact person . 12 A.3 Identification of the Protocol 12 A.4 AS Roles . 13 A.6 Protocols for DM-MS supporting operation with a type 2 DM-REP (MS-REP2) . 1

9、3 A.6.1 A.6.1.1 DMCC major capabilities . 13 A.6.1.2 Circuit mode call . 14 A.6.1.3 Circuit mode call Set-up 14 A.6.1.4 Circuit mode services offered . 15 A.6.1.5 Short data services 15 A.6.1.6 Type of short data service . 16 A.6.1.7 Data transmission 17 A.6.1.8 SDS user defined data . 17 DMCC PDUs

10、18 A.6.1.9 A.6.1.10 DMCC constants . 20 A.6.1.11 DMCC timers 21 A.6.2 MS-REP2 Data link layer (DLL) at Layer 2 22 A.6.2.1 MS-REP2 MAC featiires 22 A.6.2.2 MS-REP2-MAC procedures . 22 A.6.2.3 MS-REP2 MAC PDUs . 26 A.6.2.4 MS-REP2 MAC generated messages . 27 A.6.2.5 MS-REP2 MAC constants 27 A.6.2.6 MS

11、-REP2 MAC timers . 29 A.7 DM-REP type 2 Protocol (DM-REP2) . 30 A.7.1 DM-REP2 Data link layer (DLL) at Layer 2 30 A.7.1.1 Major services . 30 A.7.1.2 DM-REP2 MAC features 30 Guidance for completing the PICS proforma . 8 Purposes and structure 8 Identification of the implementation 10 Abbreviations a

12、nd conventions 8 Instructions for completing the PICS proforma 10 Date of the statement 10 Global statement of conformance . 12 MS-REP2 Direct Mode Call Control (DMCC) at Layer 3 . 13 ETSI A.7. A.7. A.7. 4 ETSI TS 1 O0 396-8-4 V1.l.l (2000-1 O) . 3 . 5 A.7.1.6 A.7.1.7 A.8 DM-REP2 MAC procedures . 31

13、 DM-REP2 MAC generated messages . 33 DM-REP2 MAC constants . 33 DM-REP2 MAC timers 34 PDU parameters for MS-REP2 and DM-REP2 used in DMCC at layer 3 and DLL at layer 2 . 35 . 4 DM-REP2 MAC PDUS . 33 A.8.1 A.8.1.1 A.8.1.2 A.8.1.3 A.8.1.4 A.8.1.5 A.8.1.6 A.8.1.7 A.8.1.8 A.8.1.9 A.8.1.10 A.8.1.11 A.8.1

14、.12 A.8.1.13 A.8.1.14 A.8.1.15 A.8.1.16 A.8.1.17 A.8.2 A.8.2.1 A.8.2.2 A.8.2.3 A.8.2.4 A.8.2.5 A.8.2.6 A.8.3 A.8.3.1 A.8.3.2 A.8.3.3 A.8.3.4 MS-REP2 PDU parameters for DMCC at layer 3 35 DM-SETUP 35 DM-SETUP PRES 35 DM-CONNECT 36 DM-DISCONNECT . 36 DM-CONNECT ACK 36 DM-OCCUPIED . 37 DM-RELEASE . 37

15、DM-TX CEASED . 37 DM-TX REQUEST 38 DM-TX ACCEPT . 38 DM-PREEMPT . 38 DM-PRE ACCEPT . 38 DM-REJECT 38 DM-INFO . 39 DM-SDS UDATA 39 DM-SDS DATA . 40 DM-SDS ACK 40 MS-REP2 and DM-REP2 PDU parameters for DLL at layer 2 . 41 DMAC-SYNC in SCH/S 41 DPRES-SYNC PDU . 42 DMAC-DATA 43 DMAC-FRAG 43 DMAC-END . 4

16、3 DMAC-U SIGNAL . 43 DM-MAC generated message parameters 44 DM-RESERVED 44 DM-SDS OCCUPIED 44 DM-TIMING REQUEST . 44 DM-TIMING ACK . 44 History 45 ETSI 5 ETSI TS 1 O0 396-8-4 V1.l.l (2000-1 O) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been

17、declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR O00 3 14: “Intellectual Propero Rights (IPRs); Essential, or potentially Essential, IPRs notifed to ETSI in respect of ETSI standards“, wh

18、ich is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/www.etsi.ordipr). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced

19、 in ETSI SR O00 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Project Terrestrial Trunked Radio (TETRA). The present document is part 8 of a multi-part deliverab

20、le covering the Terrestrial Trunked Radio (TETRA); Technical requirements for Direct Mode Operation (DMO); as identified below: Part 1: “General network design“; Part 2: “Radio aspects“; Part 3: “Mobile Station to Mobile Station (MS-MS) Air Interface (AI) protocol“; Part 4: “Type 1 repeater air inte

21、rface“; Part 5: “Gateway air interface“; Part 6: “Security“; Part 7: “Type 2 repeater air interface“; Part 8: “Protocol Implementation Conformance Statement (PICS) proforma specification“; Part 9: “Service and Description Language (SDL) model“; Part 10: “Managed Direct Mode Operation (DMO)“. Introdu

22、ction To evaluate conformance of a particular implementation, it is necessary to have a statement of which capabilities and options have been implemented for a telecommunication specification. Such a statement is called an Implementation Conformance Statement (ICs). ETSI 6 ETSI TS 1 O0 396-8-4 V1.l.

23、l (2000-1 O) 1 Scope The present documet provides the Protocol Implementation Conformance Statement (PICS) proforma for TETRA Direct Mode Operation (DMO) Mobile Stations (MS) connected to Type 2 repeater (MS-REP2) and for TETRA Direct Mode Operation Type 2 repeater (DM-REP2), defined in EN 300 396-7

24、 11 in compliance with the relevant requirements, and in accordance with the relevant guidance given in ISO/IEC 9646-7 6 and ETS 300 406 4. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are eit

25、her specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. il ETSI EN 300 396-7: “Terrestrial Trunked Radio (TETRA); Technical requireme

26、nts for Direct Mode Operation (DMO); Part 7: Type 2 repeater air interface“. ETSI ETS 300 396-3: “Terrestrial Trunked Radio (TETRA); Technical requirements for Direct Mode Operation (DMO); Part 3: Mobile Station to Mobile Station (MS-MS) Air Interface (AI) protocol“. Pl ETSI EN 300 396-8-2: “Terrest

27、rial Trunked Radio (TETRA); Technical requirements for Direct Mode Operation (DMO); Part 8: Protocol Implementation Conformance Statement (PICS) proforma specification; Sub-part 2: Type 1 repeater Air Interface (AI)“. ETSI ETS 300 406: “Methods for Testing and Specification (MTS); Protocol and profi

28、le conformance testing specifications; Standardization methodology“. ISO/IEC 9646- 1 (1994): “Information technology - Open systems interconnection - Conformance testing methodology and framework - Part 1: General concepts“. ISO/IEC 9646-7 (1995): “Information technology - Open systems interconnecti

29、on - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. ETSI EN 300 396-4: “Terrestrial Trunked Radio (TETRA); Technical requirements for Direct Mode Operation (DMO); Part 4: Type 1 repeater air interface“. 3 3.1 Definitions and abbreviations Definitions

30、For the purposes of the present document, the terms and definitions given in EN 300 396-4 7, ISO/IEC 9646-1 5, ISO/IEC 9646-7 6 and the following apply. Implementation Conformance Statement (ICs): statement made by the supplier of an implementation or system claimed to conform to a given specificati

31、on, stating which capabilities have been implemented. The ICs can take several forms: protocol ICs, profile ICs, profile specific ICs, information object ICs, etc. ICs proforma: document, in the form of a questionnaire, which when completed for an implementation or system becomes an ICs Protocol ICs

32、 (PICS): ICs for an implementation or system claimed to conform to a given protocol specification ETSI 7 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: ICs Implementation Conformance Statement IUT Implementation Under Test PICS Protocol Implementation

33、Conformance Statement SCS System Conformance Statement SUT System Under Test ETSI TS 1 O0 396-8-4 V1.l.l (2000-1 O) 4 Conformance to this PICS proforma specification If it claims to conform to the present document, the actual PICS proforma to be filled in by a supplier shall be technically equivalen

34、t to the text of the PICS proforma given in annex A, and shall preserve the numberinghaming and ordering of the proforma items. A PICS which conforms to the present document shall be a conforming PICS proforma completed in accordance with the guidance for completion given in clause A. 1. ETSI 8 ETSI

35、 TS 1 O0 396-8-4 V1.l.l (2000-1 O) Annex A (normative): Protocol ICs proforma (PICS) for EN 300 396-4 Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may freely reproduce the PICS proforma in this anne

36、x so that it can be used for its intended purposes and may further publish the completed PICS. A.l Guidance for completing the PICS proforma A. 1 .I Purposes and structure The purpose of this PICS proforma is to provide a mechanism whereby a supplier of an implementation of the requirements defined

37、in EN 300 396-7 11 may provide information about the implementation in a standardized manner. The PICS proforma is subdivided into clauses for the following categories of information: guidance for completing the PICS proforma; identification of the implementation; identification of the Protocol; glo

38、bal statement of conformance; identification of the roles, MS-REP2 or DM-REP2; MS-REP2 layer 3 protocol part; MS-REP2 protocol layer 2 part; DM-REP2part. A. 1.2 Abbreviations and conventions The PICS proforma contained in this annex is comprised of information in tabular form in accordance with the

39、guidelines presented in ISO/IEC 9646-7 6. Item column The item column contains a number which identifies the item in the table. Item description column The item description column describes in free text each respective item (e.g. parameters, timers, etc.). It implicitly means “is supported by the im

40、plementation?“. Status column The following notations, defined in ISO/IEC 9646-7 6, are used for the status column: m O n/a X mandatory - the capability is required to be supported; optional - the capability may be supported or not; not applicable - in the given context, it is impossible to use the

41、capability; prohibited (excluded) - there is a requirement not to use this capability in the given context; ETSI 9 ETSI TS 1 O0 396-8-4 V1.l.l (2000-1 O) 0.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies a unique group of related opt

42、ional items and the logic of their selection which is defined immediately following the table; conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying a unique conditional status expression

43、which is defined immediately following the table. ci Reference column The reference column makes reference to EN 300 396-7 i, except where explicitly stated otherwise. Support column The support column shall be filled in by the supplier of the implementation. The following common notations, defined

44、in ISO/IEC 9646-7 6, are used for the support column: Y or y N or n N/A, n/a or - supported by the implementation; not supported by the implementation; no answer required (allowed only if the status is n/a, directly or after evaluation of a conditional status). If this PICS proforma is completed in

45、order to describe a multiple-profile support in a system, it is necessary to be able to answer that a capability is supported for one profile and not supported for another. In that case, the supplier shall enter the unique reference to a conditional expression, preceded by “?“ (e.g. ?3). This expres

46、sion shall be given in the space for comments provided at the bottom of the table. It uses predicates defined in the SCS, each of which refers to a single profile and which takes the value TRUE if and only if that profile is to be used. EXAMPLE: ?3: IF prof1 THEN Y ELSE N It is also possible to prov

47、ide a comment to an answer in the space provided at the bottom of the table. NOTE: As stated in ISO/IEC 9646-7 6, support for a received PDU requires the ability to parse all valid parameters of that PDU. Supporting a PDU while having no ability to parse a valid parameter is non-conformant. Support

48、for a parameter on a PDU means that the semantics of that parameter are supported. Values allowed column The values allowed column contains the type, the list, the range, or the length of values allowed. The following notations are used: range of values: example: 5 20 list of values: , , , example:

49、2,4, 6, 8,9 example: 1 101B, 101 lB, 1 11 1B example: OAH, 34H, 2F“ list of named values: (), (), , ( example: reject(l), accept(2) length: size ( ) example: size (1 8) ETSI 10 ETSI TS 1 O0 396-8-4 V1.l.l (2000-1 O) Values supported column The values supported column shall be filled in by the supplier of the implementation. In this column, the values or the ranges of values supported by the implementation shall be indicated. References to items For each possible item answer (answer in the support column) within the PICS proforma a unique referen