ETSI TS 100 392-18-3-2010 Terrestrial Trunked Radio (TETRA) Voice plus Data (V+D) and Direct Mode Operation (DMO) Part 18 Air interface optimized applications Sub-part 3 Direct mod_1.pdf

《ETSI TS 100 392-18-3-2010 Terrestrial Trunked Radio (TETRA) Voice plus Data (V+D) and Direct Mode Operation (DMO) Part 18 Air interface optimized applications Sub-part 3 Direct mod_1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 100 392-18-3-2010 Terrestrial Trunked Radio (TETRA) Voice plus Data (V+D) and Direct Mode Operation (DMO) Part 18 Air interface optimized applications Sub-part 3 Direct mod_1.pdf（43页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 100 392-18-3 V1.2.1 (2010-12)Technical Specification Terrestrial Trunked Radio (TETRA);Voice plus Data (V+D) and Direct Mode Operation (DMO);Part 18: Air interface optimized applications;Sub-part 3: Direct mode OverThe Air Management protocol (DOTAM)ETSI ETSI TS 100 392-18-3 V1.2.1 (2010-12

2、) 2Reference RTS/TETRA-03209 Keywords air interface, DMO, management, TETRA, V+D ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grass

3、e (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the re

4、ference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or c

5、hange of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyri

6、ght Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2010. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo an

7、d the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. LTE is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP O

8、rganizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 100 392-18-3 V1.2.1 (2010-12) 3Contents Intellectual Property Rights 5g3Foreword . 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Defini

9、tions, symbols and abbreviations . 7g33.1 Definitions 7g33.2 Symbols 7g33.3 Abbreviations . 8g34 Direct mode operation over the air management protocol . 8g34.1 General . 8g34.2 DOTAM protocol system architecture . 9g34.3 DOTAM protocol service description 11g34.3.1 General on DOTAM services . 11g34

10、.3.2 Services available at the DOTAM-SAP 11g34.3.3 Service primitives at the DOTAM-SAP . 11g34.3.4 Service primitive parameters at the DOTAM-SAP 12g34.3.5 State description 12g35 DOTAM protocol description 13g35.1 Description of information elements 13g35.1.1 Acknowledgement request 13g35.1.2 Air in

11、terface encryption state 13g35.1.3 DMO frequency 13g35.1.4 DMO frequency mnemonic name . 13g35.1.5 DMO group status . 13g35.1.6 DMO group mnemonic name . 14g35.1.7 Encryption key number . 14g35.1.8 Group number . 14g35.1.9 Interrogate range . 14g35.1.10 Selected group 14g35.1.11 Unique DMO group ide

12、ntifier 14g35.2 Information flows . 15g35.2.1 General on information flows . 15g35.2.2 MS receiving DMO group assignment without an acknowledgement 15g35.2.3 MS receiving DMO group assignment with an acknowledgement . 16g35.2.4 Deassignment of DMO group definitions . 17g35.2.5 Change of status of DM

13、O group definitions . 17g35.2.6 Interrogation of DMO group definitions . 17g35.2.7 MS receiving DMO control group with an acknowledgement . 18g35.3 Functional entity actions 18g35.3.1 FE1 actions . 18g35.3.2 FE2 actions . 19g35.3.3 FE3 actions . 20g35.4 Allocation of entities 21g35.5 Procedures 21g3

14、5.5.1 Relations to flow charts 21g35.5.2 Moving from V+D to DMO and Powering on in DMO . 21g35.5.3 MS receiving DMO group assignment . 22g35.5.4 MS receiving DMO group deassignment 22g35.5.5 MS receiving DMO group status change 23g35.5.6 MS receiving DMO interrogation request 23g35.5.7 MS receiving

15、DOTAM control group address 24g3ETSI ETSI TS 100 392-18-3 V1.2.1 (2010-12) 45.5.8 MS receiving PDU using DOTAM control group address . 24g35.6 Operational requirements . 25g35.6.1 DMO capable MS . 25g35.6.2 DMO capable MS home SwMI 25g36 DOTAM protocol coding requirements . 25g36.1 General on coding

16、 requirements . 25g36.2 DOTAM protocol PDU description tables . 26g36.2.1 ASSIGN PDU . 26g36.2.2 ASSIGN ACK PDU 26g36.2.3 CHANGE STATUS PDU . 27g36.2.4 CHANGE STATUS ACK PDU . 27g36.2.5 DEASSIGN PDU 28g36.2.6 DEASSIGN ACK PDU 28g36.2.7 GROUP PROVIDE PDU 29g36.2.8 GROUP PROVIDE ACK PDU 29g36.2.9 INTE

17、RROGATE PDU . 30g36.2.10 INTERROGATE ACK PDU 30g36.2.11 INTERROGATE CONTROL GROUPS ACK PDU 31g36.3 PDU information elements . 31g36.3.1 Acknowledgement request 31g36.3.2 Air Interface encryption state 31g36.3.3 DMO channel mnemonic name 32g36.3.4 DMO frequency 32g36.3.5 DMO group deassign type 32g36

18、.3.6 DMO group definition 33g36.3.7 DMO group mnemonic name . 33g36.3.8 DMO group status . 33g36.3.9 DMO group status change type. 34g36.3.10 Encryption key number . 34g36.3.11 Group Short Subscriber Identity . 34g36.3.12 Interrogate range . 34g36.3.13 Interrogate type . 35g36.3.14 Maximum response

19、time . 35g36.3.15 Mobile Network Identity 35g36.3.16 PDU type 36g36.3.17 Reserved information element present 36g36.3.18 Result code 37g36.3.19 Type 5 element identifier (informative) 37g36.3.20 Unique DMO group identifier 38g36.4 Type 5 information element description (informative). 38g36.4.1 Type

20、5 information element definition . 38g36.4.2 Type 5 element length . 38g36.4.3 Type 5 element length extension 38g36.4.4 Type 5 information element 39g37 Interactions with other services 39g37.1 Direct mode 39g37.2 Direct mode dual watch 39g37.3 Intersystem interface 39g3Annex A (normative): Service

21、 or action not supported U/D FACILITY PDU option. 40g3Annex B (normative): Service or action not supported SDS-TL PDU option 41g3Annex C (informative): Change Requests 42g3History 43g3ETSI ETSI TS 100 392-18-3 V1.2.1 (2010-12) 5Intellectual Property Rights IPRs essential or potentially essential to

22、the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ET

23、SI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given

24、 as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Terrestrial Trunked Radio (TET

25、RA). The present document is part 18, sub-part 3 of a multi-part deliverable covering the Terrestrial Trunked Radio (TETRA); the Voice plus Data (V+D), as identified below: EN 300 392-1: “General network design“; EN 300 392-2: “Air Interface (AI)“; EN 300 392-3: “Interworking at the Inter-System Int

26、erface (ISI)“; ETS 300 392-4: “Gateways basic operation“; TS 100 392-5: “Peripheral Equipment Interface (PEI)“; TS 100 392-7: “Security“; EN 300 392-9: “General requirements for supplementary services“; EN 300 392-10: “Supplementary services stage 1“; TS 100 392-11: “Supplementary services stage 2“;

27、 TS 100 392-12: “Supplementary services stage 3“; ETS 300 392-13: “SDL model of the Air Interface (AI)“; ETS 300 392-14: “Protocol Implementation Conformance Statement (PICS) proforma specification“; TS 100 392-15: “TETRA frequency bands, duplex spacings and channel numbering“; TS 100 392-16: “Netwo

28、rk Performance Metrics“; TR 100 392-17: “TETRA V+D and DMO specifications“; TS 100 392-18: “Air interface optimized applications“. Sub-part 1: “Location Information Protocol (LIP)“; Sub-part 2: “Net Assist Protocol (NAP)“. Sub-part 3: “Direct mode Over The Air Management protocol (DOTAM)“. NOTE: Par

29、t 3, sub-parts 6 and 7 (Speech format implementation), part 4, sub-part 3 (Data networks gateway), part 10, sub-part 15 (Transfer of control), part 13 (SDL) and part 14 (PICS) of this multi-part deliverable are in status “historical“ and are not maintained. ETSI ETSI TS 100 392-18-3 V1.2.1 (2010-12)

30、 61 Scope The present document defines the Direct mode operation Over The Air Management protocol for the TETRA V+D air interface. It defines the following services: Direct Mode Operation over the air management service. Interrogation of Direct Mode Operation groups and their status. 2 References Re

31、ferences are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced

32、documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. 2.1 Normative references The fol

33、lowing referenced documents are necessary for the application of the present document. 1 ETSI EN 300 392-1: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 1: General network design“. 2 ETSI EN 300 392-2: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 2: Air Interfac

34、e (AI)“. 3 ETSI EN 300 392-9: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 9: General requirements for supplementary services“. 4 ETSI TS 100 392-15: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 15: TETRA frequency bands, duplex spacings and channel numbering“.

35、5 ETSI EN 300 396-3: “Terrestrial Trunked Radio (TETRA); Technical requirements for Direct Mode Operation (DMO); Part 3: Mobile Station to Mobile Station (MS-MS) Air Interface (AI) protocol“. 6 ETSI EN 300 396-6: “Terrestrial Trunked Radio (TETRA); Direct Mode Operation (DMO); Part 6: Security“. 7 E

36、TSI EN 300 392-7: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 7: Security“. 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. Not applicabl

37、e. ETSI ETSI TS 100 392-18-3 V1.2.1 (2010-12) 73 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in EN 300 392-2 2 and EN 300 396-3 5 and the following apply: assign: addition of group definition assigned DMO group: DMO

38、 group with a valid parameter set NOTE: DMO groups are assigned by a network operator. deassign: permanent removal of DMO group definition default DMO group: DMO group which is automatically selected when a mobile station switches from V+D to DMO NOTE: There can be only a single default DMO group at

39、 any time.DMO channel: Radio Frequency (RF) carrier for DMO usage DMO group: DMO group defined by the parameter set: a TETRA group address, a mnemonic group name, a DMO channel, and a mnemonic DMO channel name NOTE: DMO group identifiers contain some additional parameters to the above list that is s

40、een on the users point of view. management server: entity that manages DMO equipment management source: originator of DMO management commands preferred DMO group: DMO group which has been assigned to a specific organisation for preferred usage NOTE: There can be multiple preferred DMO groups defined

41、 at the same time. selected DMO group: DMO group that MS user has selected NOTE: A selected DMO group can be a default, a preferred or an assigned DMO group. Switching And Management Infrastructure (SwMI): all of the TETRA equipment for a Voice plus Data (V+D) network except for subscriber terminals

42、 TETRA domain: all entities that are addressed using TETRA defined addresses NOTE: TETRA domain, as defined, may contain entities that are not controlled by TETRA security features. 3.2 Symbols For the purposes of the present document, the following symbols apply: ra relationship between management

43、server entity and managed DMO entity rb relationship between management source entity and management server entity rc relationship between management source entity and managed DMO entity rd relationship between communication management entity and management server entity re relationship between auth

44、entication entity and management server entity rf relationship between group number and radio resource management entity and management server entity rg relationship between communication management entity and authentication entity ETSI ETSI TS 100 392-18-3 V1.2.1 (2010-12) 83.3 Abbreviations For th

45、e purposes of the present document, the following abbreviations apply: C Conditional DGNA Dynamic Group Number Assignment DMO Direct Mode Operation DOTAM Direct mode operation Over The Air Management FE Functional Entity GTSI Group TETRA Subscriber Identity ISDN Integrated Services Digital Network I

46、SSI Individual Short Subscriber Identity ITSI Individual TETRA Subscriber Identity M Mandatory MNI Mobile Network Identity MS Mobile Station MS-ISDN Mobile Station ISDN number OTAK Over The Air Keying OTAR Over The Air Re-keying PDU Protocol Data Unit RF Radio Frequency SAP Service Access Point SCK

47、Static Cipher Key SDS-TL Short Data Service - Transport Layer SS-DGNA Supplementary Service Dynamic Group Number Assignment SwMI Switching And Management Infrastructure V+D Voice plus Data system 4 Direct mode operation over the air management protocol 4.1 General The Direct mode operation Over The

48、Air Management (DOTAM) is a TETRA air interface management protocol that could utilize various transport mechanisms. The present document defines “control messages“ to set and modify MS behaviour in DMO. The management protocol can be used in various system configurations including: SwMI to MS commu

49、nication. Management server to MS communication. MS to management server communication. NOTE 1: Although DOTAM protocol can support direct MS to individual MS communication; the use of it may be limited to specific situations and is outside the scope of the present document. NOTE 2: DMO groups are normally assigned by a network operator. NOTE 3: DOTAM does not preclude the usage of pre-configured group and/or frequency settings. It is outside the scope of the present document how DOTAM and pre-configured group and/or frequency settings may interac