ETSI TR 136 903-2018 LTE Evolved Universal Terrestrial Radio Access (E-UTRA) and Evolved Universal Terrestrial Radio Access Network (E-UTRAN) Derivation of test tolerances for Radi.pdf

《ETSI TR 136 903-2018 LTE Evolved Universal Terrestrial Radio Access (E-UTRA) and Evolved Universal Terrestrial Radio Access Network (E-UTRAN) Derivation of test tolerances for Radi.pdf》由会员分享，可在线阅读，更多相关《ETSI TR 136 903-2018 LTE Evolved Universal Terrestrial Radio Access (E-UTRA) and Evolved Universal Terrestrial Radio Access Network (E-UTRAN) Derivation of test tolerances for Radi.pdf（40页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TR 136 903 V13.4.0 (2018-01) LTE; Evolved Universal Terrestrial Radio Access (E-UTRA) and Evolved Universal Terrestrial Radio Access Network (E-UTRAN); Derivation of test tolerances for Radio Resource Management (RRM) conformance tests (3GPP TR 36.903 version 13.4.0 Release 13) floppy3TECHNICA

2、L REPORT ETSI ETSI TR 136 903 V13.4.0 (2018-01)13GPP TR 36.903 version 13.4.0 Release 13Reference RTR/TSGR-0536903vd40 Keywords LTE ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but

3、 non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions

4、 of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specifi

5、c network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find

6、 errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm

7、 except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2018. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETS

8、I logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM and the GSM logo are trademarks registered an

9、d owned by the GSM Association. ETSI ETSI TR 136 903 V13.4.0 (2018-01)23GPP TR 36.903 version 13.4.0 Release 13Intellectual Property Rights Essential patents IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential

10、IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are

11、available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) whic

12、h are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and c

13、onveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Technical Report (TR) has been produced by ETSI 3r

14、d Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS

15、, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal

16、 forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TR 136 903 V13.4.0 (2018-01)33GPP TR 36.903 version 13.4.0 Release 13Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3F

17、oreword . 5g3Introduction 5g31 Scope 6g32 References 6g33 Definitions, symbols and abbreviations . 6g33.1 Definitions 6g33.2 Symbols 7g33.3 Abbreviations . 7g34 General Principles 7g34.1 Principle of Superposition 7g34.2 Sensitivity analysis . 7g34.3 Statistical combination of uncertainties 7g34.4 C

18、orrelation between uncertainties 8g34.4.1 Uncorrelated uncertainties 8g34.4.2 Positively correlated uncertainties 9g34.4.3 Negatively correlated uncertainties . 9g34.4.4 Treatment of uncorrelated uncertainties . 10g34.4.5 Treatment of positively correlated uncertainties with adverse effect 10g34.4.6

19、 Treatment of positively correlated uncertainties with beneficial effect 10g34.4.7 Treatment of negatively correlated uncertainties 10g35 Grouping of test cases defined in TS 36.521-3 11g35A Grouping of test cases defined in TS 37.571-1 13g36 Determination of Test System Uncertainties 13g36.1 Genera

20、l . 13g36.2 Uncertainty figures . 13g37 Determination of Test Tolerances 14g37.1 General . 14g3Annex A: Derivation documents 15g3Annex B: Default uncertainties for test cases defined in TS 36.521-3 16g3B.0 AWGN and Fading . 16g3B.1 Group A: E-UTRA Intra-frequency mobility . 16g3B.2 Group B: E-UTRA I

21、nter-frequency mobility . 16g3B.3 Group C: E-UTRA Intra-frequency UE reporting accuracy 17g3B.4 Group D: E-UTRA Inter-frequency UE reporting accuracy 18g3B.5 Group E: E-UTRA Random Access . 18g3B.6 Group F: E-UTRA Transmit timing and Timing advance . 19g3B.7 Group G: E-UTRA In-sync and Out-of-sync .

22、 20g3B.8 Group H: E-UTRA to UTRA Inter-RAT mobility . 20g3B.9 Group I: E-UTRA to GSM Inter-RAT mobility. 21g3ETSI ETSI TR 136 903 V13.4.0 (2018-01)43GPP TR 36.903 version 13.4.0 Release 13Annex C: Default uncertainties for test cases defined in TS 37.571-1 22g3Annex D: Change History 23g3History 39g

23、3ETSI ETSI TR 136 903 V13.4.0 (2018-01)53GPP TR 36.903 version 13.4.0 Release 13Foreword This Technical Report has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG app

24、roval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3

25、 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. Introduction

26、ETSI ETSI TR 136 903 V13.4.0 (2018-01)63GPP TR 36.903 version 13.4.0 Release 131 Scope The present document specifies a general method used to derive Test Tolerances for Radio Resource Management tests, and establishes a system for relating the Test Tolerances to the measurement uncertainties of the

27、 Test System. The test cases which have been analysed to determine Test Tolerances are included as .zip files. The present document is applicable from Release 8 up to the release indicated on the front page of the present Terminal conformance specifications. 2 References The following documents cont

28、ain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specif

29、ic reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document unless the context in which the reference is made suggests

30、 a different Release is relevant (information on the applicable release in a particular context can be found in e.g. test case title, description or applicability, message description or content). 1 3GPP TR 21.905: “Vocabulary for 3GPP Specifications“. 2 ETSI ETR 273-1-2: “Improvement of radiated me

31、thods of measurement (using test sites) and evaluation of the corresponding measurement uncertainties; Part 1: Uncertainties in the measurement of mobile radio equipment characteristics; Sub-part 2: Examples and annexes“. 3 3GPP TS 34.121-1: “Terminal conformance specification, Radio transmission an

32、d reception (FDD), Release 8“. 4 3GPP TS 36.521-1: “User Equipment (UE) conformance specification, Radio transmission and reception Part 1: conformance testing, Release 8“. 5 3GPP TS 36.521-3: “User Equipment (UE) conformance specification, Radio transmission and reception Part 3: Radio Resource Man

33、agement (RRM) conformance testing, Release 8“. 6 3GPP TS 36.141: “E-UTRA Base Station (BS) conformance testing, Release 8“ 7 3GPP TS 36.211: “E-UTRA Physical Channels and Modulation, Release 8“ 8 3GPP TS 37.571-1: “Universal Terrestrial Radio Access (UTRA) and Evolved UTRA (E-UTRA) and Evolved Packe

34、t Core (EPC); User Equipment (UE) conformance specification for UE positioning; Part 1: Terminal conformance”. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in TR 21.905 1 apply. A term defined in the present docume

35、nt takes precedence over the definition of the same term, if any, in TR 21.905 1. Other definitions used in the present document are listed in 3GPP TS 36.521-3 5 or 3GPP TS 36.141 6. ETSI ETSI TR 136 903 V13.4.0 (2018-01)73GPP TR 36.903 version 13.4.0 Release 133.2 Symbols Symbols used in the presen

36、t document are listed in 3GPP TR 21.905 1, 3GPP TS 36.521-3 5 or 3GPP TS 36.141 6. 3.3 Abbreviations For the purposes of the present document, the abbreviations given in TR 21.905 1 apply. An abbreviation defined in the present document takes precedence over the definition of the same abbreviation,

37、if any, in TR 21.905 1. Other abbreviations used in the present document are listed in 3GPP TS 36.521-3 5 or 3GPP TS 36.141 6. 4 General Principles 4.1 Principle of Superposition For multi-cell tests there are several cells each generating various Physical channels. In general cells are combined alo

38、ng with AWGN, so the signal and noise seen by the UE may be determined by more than one cell. Since several cells may contribute towards the overall power applied to the UE, a number of test system uncertainties affect the signal and noise seen by the UE. The aim of the superposition method is to va

39、ry each controllable parameter of the test system separately, and to establish its effect on the critical parameters as seen by the UE receiver. The superposition principle then allows the effect of each test system uncertainty to be added, to calculate the overall effect. The contributing test syst

40、em uncertainties shall form a minimum set for the superposition principle to be applicable. 4.2 Sensitivity analysis A change in any one channel level or channel ratio generated at source does not necessarily have a 1:1 effect at the UE. The effect of each controllable parameter of the test system o

41、n the critical parameters as seen by the UE receiver shall therefore be established. As a consequence of the sensitivity scaling factors not necessarily being unity, the test system uncertainties cannot be directly applied as test tolerances to the critical parameters as seen by the UE. EXAMPLE: In

42、many of the tests described, the s / Iotis one of the critical parameters at the UE. Scaling factors are used to model the sensitivity of the s / Iotto each test system uncertainty. When the scaling factors have been determined, the superposition principle then allows the effect of each test system

43、uncertainty to be added, to give the overall variability in the critical parameters as seen at the UE. There are often constraints on several parameters at the UE. The aim of the sensitivity analysis, together with the acceptable test system uncertainties, is to ensure that the variability in each o

44、f these parameters is controlled within the limits necessary for the specification to apply. The test has then been conducted under valid conditions. 4.3 Statistical combination of uncertainties The acceptable uncertainties of the test system are specified as the measurement uncertainty tolerance in

45、terval for a specific measurement that contains 95 % of the performance of a population of test equipment, in accordance with 3GPP TS 36.521-3 5 clause F.1. In the RRM tests covered by the present document, the Test System shall enable the stimulus signals in the test case to be adjusted to within t

46、he specified range, with an uncertainty not exceeding the specified values. The method given in the present document combines the acceptable uncertainties of the test system, to give the overall variability in the critical parameters as seen at the UE. Since the process does not add any new uncertai

47、nties, the method of combination should be chosen to maintain the same tolerance interval for the combined uncertainty as is already specified for the contributing test system uncertainties. The basic principle for combining uncertainties is in accordance with ETR 273-1-2 2. In summary, the process

48、requires 3 steps: ETSI ETSI TR 136 903 V13.4.0 (2018-01)83GPP TR 36.903 version 13.4.0 Release 13a) Express the value of each contributing uncertainty as a one standard deviation figure, from knowledge of its numeric value and its distribution. b) Combine all the one standard deviation figures as ro

49、ot-sum-squares, to give the one standard deviation value for the combined uncertainty. c) Expand the combined uncertainty by a coverage factor, according to the tolerance interval required. Provided that the contributing uncertainties have already been obtained using this method, using a coverage factor of 2, further stages of combination can be achieved by performing step b) alone, since steps a) and c) simply divide by 2 and multiply by 2 respectively. The root-sum-squares method is therefore used to maintain the same tolera