ETSI ES 200 659-3-2004 Access and Terminals (AT) Analogue access to the Public Switched Telephone Network (PSTN) Subscriber line protocol over the local loop for display (and relat.pdf

《ETSI ES 200 659-3-2004 Access and Terminals (AT) Analogue access to the Public Switched Telephone Network (PSTN) Subscriber line protocol over the local loop for display (and relat.pdf》由会员分享，可在线阅读，更多相关《ETSI ES 200 659-3-2004 Access and Terminals (AT) Analogue access to the Public Switched Telephone Network (PSTN) Subscriber line protocol over the local loop for display (and relat.pdf（31页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI ES 200 659-3 V1.4.1 (2004-08)ETSI Standard Access and Terminals (AT);Analogue access to thePublic Switched Telephone Network (PSTN);Subscriber line protocol over the local loop fordisplay (and related) services;Part 3: Data link message and parameter codingsETSI ETSI ES 200 659-3 V1.4.1 (2004-

2、08) 2 Reference RES/AT-030010 Keywords coding, data, DLC, protocol, PSTN, service, SMS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de

3、 Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions,

4、the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revisio

5、n or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp

6、Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2004. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of E

7、TSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI ES 200 659-3 V1.4.

8、1 (2004-08) 3 Contents Intellectual Property Rights5 Foreword.5 1 Scope 6 2 References 6 3 Definitions and abbreviations.6 3.1 Definitions6 3.2 Abbreviations .6 4 Data encoding.7 5 Data Link message and parameter codings 7 5.1 Data Link message and general parameter requirements .7 5.1.1 Data Link M

9、essage .7 5.1.2 Parameter 7 5.1.3 TE considerations .8 5.2 Data Link message types8 5.2.1 Call Setup message .8 5.2.2 Message Waiting Indicator message.9 5.2.3 Advice of Charge message .10 5.3 Parameter types 10 5.4 Parameter coding11 5.4.1 Date and time parameter .11 5.4.2 Calling Line Identity par

10、ameter11 5.4.3 Called Line Identity parameter .12 5.4.4 Reason for Absence of Calling Line Identity parameter.12 5.4.5 Calling Party Name parameter12 5.4.6 Reason for Absence of Calling Party Name parameter.13 5.4.7 Called Party Name parameter .13 5.4.8 Visual Indicator parameter13 5.4.9 Message Ide

11、ntification parameter .14 5.4.10 Last Message CLI parameter 14 5.4.11 Complementary Date and Time parameter .14 5.4.12 Complementary Calling Line Identity parameter .15 5.4.13 Call Type parameter15 5.4.14 First Called Line Identity parameter .16 5.4.15 Number of Messages parameter16 5.4.16 Type of F

12、orwarded Call parameter .16 5.4.17 Type of Calling User parameter17 5.4.18 Redirecting Number parameter.17 5.4.19 Charge parameter17 5.4.20 Additional Charge parameter19 5.4.21 Duration of the Call parameter .20 5.4.22 Network Provider Identity parameter .20 5.4.23 Carrier Identity parameter.20 5.4.

13、24 Selection of Terminal Function parameter21 5.4.25 Display information parameter .21 5.4.26 Service Information parameter .22 5.4.27 Extension for network operator use parameter .22 Annex A (normative): PSTN CLIP service parameter list.23 Annex B (normative): Parameter list per service24 Annex C (

14、informative): International reference alphabet - 7-bit basic code table.27 Annex D (informative): Examples for charge parameter use.28 ETSI ETSI ES 200 659-3 V1.4.1 (2004-08) 4 D.1 Example: Currency amount (23,45 EUR) 28 D.2 Example: Only units (23) without price per unit28 D.3 Example: Units (78) w

15、ith price per unit (0,12 EUR) .29 Annex E (informative): Bibliography.30 History 31 ETSI ETSI ES 200 659-3 V1.4.1 (2004-08) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPR

16、s, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are ava

17、ilable on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). The attention of ETSI has been drawn to the Intellectual Property Rights (IPRs) listed below which are, or may be, or may become, Essential to the present document and, in particular, on hook data transmission associated with ringin

18、g, network operator option: “transmission during ringing“. The IPR owner has undertaken to grant irrevocable licences, on fair, reasonable and non-discriminatory terms and conditions under these IPRs pursuant to the ETSI IPR Policy. Further details pertaining to these IPRs can be obtained directly f

19、rom the IPR owner. The present IPR information has been submitted to ETSI and pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the

20、ETSI Web server) which are, or may be, or may become, essential to the present document. IPRs: USA 4,582,956 Canada 1,225,726Belgium 0,150,181 France 0,150,181United Kingdom 0,150,181 Japan 1,832,616Netherlands 0,150,181 Sweden 0,150,181Germany 3,376,377 The related International Patent Application

21、(WHO 85/00488) designated the following countries: AT, AU, BE, BR, CH, DE, DK, FI, FR, GB, JP, LU, NL, NO, SE and SU. IPR owner: AT EN 300 659-2: “Off-hook data transmission“; ES 200 659-3: “Data link message and parameter codings“. ETSI ETSI ES 200 659-3 V1.4.1 (2004-08) 6 1 Scope The present docum

22、ent specifies the data link message and parameter codings for the PSTN subscriber line protocol to support display and related services sent by the Local Exchange (LE). The data transmission in the subscriber line protocol is accomplished by using asynchronous voice-band Frequency-Shift Keying (FSK)

23、 signalling. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific refere

24、nce, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ETSI ETS 300 648: “Public Switched Telephone Network (PSTN

25、); Calling Line Identification Presentation (CLIP) supplementary service; Service description“. 2 Annex to ITU-T Operational Bulletin No. 805: “List of ITU-T Recommendation E.164 Assigned Country Codes (Complement to ITU-T Recommendation E.164)“. 3 ITU-T Recommendation T.50: “International Reference

26、 Alphabet (IRA) (Formerly International Alphabet No. 5 or IA5) - Information technology - 7-bit coded character set for information interchange“. 4 ETSI TR 101 292: “Public Switched Telephone Network (PSTN); Protocol over the local loop for display and related services; Proposed enhancements and mai

27、ntenance of existing standards“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETS 300 648 1 apply. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AOC-D Advice Of Charge Dur

28、ing the call AOC-E Advice Of Charge at the End of the call AOC-S Advice Of Charge at call Set-up CCBS Completion of Calls to Busy Subscriber CCNR Completion of Calls on No Reply CLIP Calling Line Identification Presentation CLIR Calling Line Identification Restriction CNIP Calling Name Identificatio

29、n Presentation CNIR Calling Name Identification Restriction CT Connection Type FSK Frequency-Shift Keying IRA International Reference Alphabet ETSI ETSI ES 200 659-3 V1.4.1 (2004-08) 7 LE Local Exchange MSN Multiple Subscriber Number MWI Message Waiting Indication NPI Network Provider Identity NPN N

30、etwork Provided Number PSTN Public Switched Telephone Network SUB SUBaddressing TE Terminal Equipment UPN User Provided Number VPN Virtual Private Network 4 Data encoding IRA, as specified in ITU-T Recommendation T.50 3 (see annex C) including national versions, shall be used for the character codin

31、g. Control characters 0/0 to 1/15 and 7/15 are not used within this protocol. Characters 8/0 to 15/15 are reserved for network operator use. 5 Data Link message and parameter codings 5.1 Data Link message and general parameter requirements 5.1.1 Data Link Message A Data Link message (for simplicity:

32、 a message) is generally related to a given service, but can be used in support of several different applications (each of them requiring different parameters). For each message type (or for each service if the same message type is used for different applications) a list of parameters is defined. Pa

33、rameters may be sent in any order within a message. A message can contain parameters for network operator use only. A range within the Message type coding is reserved for network operator use. 5.1.2 Parameter A parameter shall be used only once in each message. The parameter “Extension for network o

34、perator use“ (see clause 5.4.27) shall be included in the message when a reserved value for network operator is used in Message type, Parameter type or Parameter data value. The same parameter may be used within different messages (or different services). Parameters can be either mandatory or option

35、al according to the service description. A range within the Parameter type coding is reserved for network operator use. A range within the values of a parameter can be reserved for network operator use. ETSI ETSI ES 200 659-3 V1.4.1 (2004-08) 8 5.1.3 TE considerations The TE does not need to know wh

36、ich parameters are mandatory/optional. The TE decides how to handle the parameters (e.g. to display information or not). The TE should discard a parameter with an unknown value. The TE should discard an unknown message. The TE should discard an unknown parameter in a known message, keeping the known

37、 parameters. If mutually exclusive parameters are found in a message, the TE should discard the message. If two or more of the same parameters, but with different values, are found in a message, the TE should discard the message. If two parameters within a message are identical (same type coding val

38、ue) the TE should discard the second parameter. If the TE recognizes the “Extension for network operator“ parameter data, it should process the network operator specific Message and/or Parameter in accordance with the network operator specifications. If the TE does not recognize the “Extension for n

39、etwork operator“ parameter, the TE should discard: the complete message, if it is a network operator specific type of Message; the parameter, if it is a network operator specific Parameter or Parameter value. 5.2 Data Link message types Table 1 summarizes the messages supported in the present docume

40、nt. Table 1: Data Link message types Message Type Binary coding Hexadecimal coding Reference (clause) Call Set-up 1000 0000 80 5.2.1 Message Waiting Indicator 1000 0010 82 5.2.2 Advice of Charge 1000 0110 86 5.2.3 Reserved for Network Operator use 1111 0001 to 1111 1111 F1 to FF - 5.2.1 Call Setup m

41、essage This message is used to send information related with an incoming call. E.g. Calling Line Identification Presentation (CLIP) and related services. The Call set-up message may contain the following parameters. ETSI ETSI ES 200 659-3 V1.4.1 (2004-08) 9 Table 2: Call set-up message parameters Pa

42、rameter type Reference (clause) Date and Time 5.4.1 Calling Line Identity 5.4.2 Or Reason for absence of Calling Line Identity 5.4.4 Called Line Identity 5.4.3 Calling Party Name 5.4.5 Or Reason for absence of Calling Party Name 5.4.6 Called Party Name 5.4.7 Complementary Calling Line Identity 5.4.1

43、2 Call type 5.4.13 First Called Line Identity 5.4.14 Number of Messages 5.4.15 Type of Forwarded call 5.4.16 Type of Calling User 5.4.17 Redirecting Number 5.4.18 Network Provider Identity 5.4.22 Carrier Identity 5.4.23 Selection of Terminal Function 5.4.24 Display Information 5.4.25 Service Informa

44、tion 5.4.26 Extension for network operator use 5.4.27 Network operator parameter - See annexes A and B for the parameter status (mandatory/optional at the LE) according to service requirements. 5.2.2 Message Waiting Indicator message This message type is used to handle information related to message

45、s in a message system. The Message Waiting Indicator message may contain the following parameters. Table 3: Message Waiting Indicator message parameters Parameter type Reference (clause) Date and Time 5.4.1 Calling Line Identity 5.4.2 Or Reason for absence of Calling Line Identity 5.4.4 Calling Part

46、y Name 5.4.5 Or Reason for absence of Calling Party Name 5.4.6 Visual Indicator 5.4.8 Message Identification 5.4.9 Last Message CLI 5.4.10 Complementary Date and Time 5.4.11 Complementary Calling Line Identity 5.4.12 Number of Messages 5.4.15 Type of Calling User 5.4.17 Network Provider Identity 5.4

47、.22 Selection of Terminal Function 5.4.24 Display Information 5.4.25 Extension for network operator use 5.4.27 Network operator parameter - See annex B for the parameter status (mandatory/optional at the LE) according to service requirements. ETSI ETSI ES 200 659-3 V1.4.1 (2004-08) 105.2.3 Advice of

48、 Charge message This message is used to send information related to the charge of a call. The Advice Of Charge message may contain the following parameters. Table 4: Advice Of Charge message parameters Parameter type Reference (clause) Date and Time 5.4.1 Calling Line Identity 5.4.2 Or Reason for ab

49、sence of Calling Line Identity 5.4.4 Called Line Identity 5.4.3 Complementary Calling Line Identity 5.4.12 Charge 5.4.19 Additional Charge 5.4.20 Duration of the call 5.4.21 Network Provider Identity 5.4.22 Carrier Identity 5.4.23 Selection of Terminal Function 5.4.24 Display information 5.4.25 Extension for network operator use 5.4.27 Network operator parameter - See annex B for the parameter status (mandatory/optional at the LE) according to service requirements. NOTE: The Advice of Charge at call Set-up (AOC-S) has not been included in the present docum