ETSI EN 302 998-2-2011 Electromagnetic compatibility and Radio spectrum Matters (ERM) Transmitting equipment for terrestrial mobile TV to provide multimedia multicast service Part .pdf

《ETSI EN 302 998-2-2011 Electromagnetic compatibility and Radio spectrum Matters (ERM) Transmitting equipment for terrestrial mobile TV to provide multimedia multicast service Part .pdf》由会员分享，可在线阅读，更多相关《ETSI EN 302 998-2-2011 Electromagnetic compatibility and Radio spectrum Matters (ERM) Transmitting equipment for terrestrial mobile TV to provide multimedia multicast service Part .pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 302 998-2 V1.1.1 (2011-05)Harmonized European Standard Electromagnetic compatibilityand Radio spectrum Matters (ERM);Transmitting equipment for terrestrial mobile TVto provide multimedia multicast service;Part 2: Harmonized EN covering the essential requirementsof article 3.2 of the R Essen

2、tial, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has

3、been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by

4、 ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC i.1 (as amended) laying down a procedure for the provision of informa

5、tion in the field of technical standards and regulations. The title and reference to the present document are intended to included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC 1. See article 5.1 of Dire

6、ctive 1999/5/EC 1 for information on presumption of conformity and Harmonised Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC 1 are summarised in annex A. The present document is pa

7、rt 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 2. National transposition dates Date of adoption of this EN: 20 May 2011 Date of latest announcement of this EN (doa): 31 August 2011 Date of latest publication of new National Standard or endorsement of this

8、EN (dop/e): 29 February 2012 Date of withdrawal of any conflicting National Standard (dow): 28 February 2013 Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment wi

9、thin the scope of the R Transmitting equipment for terrestrial mobile TV to provide multimedia multicast service; Part 1: Harmonized EN covering the essential requirements of article 3.2 of the R A guide to the production of candidate Harmonized Standards for application under the R - 4 kHz between

10、174 MHz and 400 MHz; - 100 kHz between 400 MHz and 790 MHz; - 4 kHz between 790 MHz and 862 MHz; - 100 kHz between 862 MHz and 1 000 MHz; - 100 kHz above 1 000 MHz. ETSI ETSI EN 302 998-2 V1.1.1 (2011-05) 8For out-of-band emissions: - 4 kHz. For Cabinet Radiation measurements please refer to EN 5501

11、6-1-1 3 or CISPR 16-2-3 4. 4.1.2 Test modulating signal The modulation signal at the input of the transmitter shall be according to OFDM signal defined in the equipment technical specification with the following specific settings: The FFT mode supported by the EUT. If more than one mode are supporte

12、d by the EUT, the mode with the largest FFT size. The guard interval duration supported by the EUT. If more than one guard interval duration are supported by the EUT, the guard interval with the shortest duration. The modulation constellation supported by the EUT. If more than one modulation constel

13、lation are supported by the EUT, the constellation with the highest order. The code ratio supported by the EUT. If more than one code ratio are supported by the EUT, an optional code ratio declared by the equipment manufacturer (or the code with the lowest ratio). 4.2 Test arrangement for measuremen

14、t of spurious emissions See clause 5.3.1 in 2 for initial conditions, test procedure and test requirements. NOTE 1: The optional filter should suppress the output signal so that no intermodulation products are generated by the spectrum analyser. The insertion loss throughout the measuring range shou

15、ld be known. NOTE 2: For high power transmitters the preferred set up would require A to be connected to B and A1 to be connected to B1. NOTE 3: For low power transmitters the preferred set up would require A to be connected to C and A1 to be connected to C1. NOTE 4: If the transmitter does not incl

16、ude any output filter, an external filter shall be added after the transmitter for the testing arrangement. This filter shall be representative of the multiplexer or filter existing in operational conditions and viewed by the transmitted output when installed. In this case, the antenna port measurem

17、ents shall be performed at the output of this extra filter. Figure 4.1: Test arrangement for spurious emissions M-TV transmitter (EUT) Power Amplifier Output Filter OFDM Exciter Input Signal Power meter / Spectrum Analyser Coupling Device Test Load Filter(s) (see note 1) Attenuator RF Output A B C A

18、1 C1 B1 ETSI ETSI EN 302 998-2 V1.1.1 (2011-05) 94.3 Test arrangement for measurement of out-of-band emissions See clause 5.3.2 in 2 for initial conditions, test procedure and test requirements. NOTE 1: Disconnect the power amplifier from the output filter. NOTE 2: The frequency response of the outp

19、ut filter must be measured and recorded (Connection A-B). NOTE 3: The spectrum of the OFDM signal at the output of the power amplifier must be measured and recorded (Connection A-C). NOTE 4: The out-of-band spectrum of the OFDM signal shall be calculated by applying the recorded frequency response o

20、f the output filter to the recorded spectrum of the OFDM signal. NOTE 5: If the transmitter does not include any output filter, an external filter shall be added after the transmitter for the testing arrangement. This filter shall be representative of the multiplexer or filter existing in operationa

21、l conditions and viewed by the transmitted output when installed. In this case, the antenna port measurements shall be performed at the output of this extra filter. Figure 4.2: Test arrangement for out-of-band emissions 4.4 Test arrangement for measurement of cabinet radiation See clause 5.3.3 in 2

22、for initial conditions, test procedure and test requirements. M-TV transmitter (EUT) Power Amplifier Output Filter OFDM Exciter Input Signal Spectrum Analyser Coupling Device Test Load RF Output Input Tracking Generator A C B ETSI ETSI EN 302 998-2 V1.1.1 (2011-05) 10NOTE: If the transmitter does no

23、t include any output filter, an external filter shall be added after the transmitter for the testing arrangement. This filter shall be representative of the multiplexer or filter existing in operational conditions and viewed by the transmitted output when installed. Figure 4.3: Test arrangement for

24、cabinet radiation M-TV transmitter (EUT) Power Amplifier Output Filter OFDM Exciter Input Signal Power meter / Spectrum Analyser Coupling Device Test Load RF Output Measuring Receiver/ Spectrum Analyser ETSI ETSI EN 302 998-2 V1.1.1 (2011-05) 11Annex A (normative): HS Requirements and conformance Te

25、st specifications Table (HS-RTT) The HS Requirements and conformance Test specifications Table (HS-RTT) in table A.1 serves a number of purposes, as follows: it provides a statement of all the requirements in words and by cross reference to (a) specific clause(s) in the present document or to (a) sp

26、ecific clause(s) in (a) specific referenced document(s); it provides a statement of all the test procedures corresponding to those requirements by cross reference to (a) specific clause(s) in the present document or to (a) specific clause(s) in (a) specific referenced document(s); it qualifies each

27、requirement to be either: - Unconditional: meaning that the requirement applies in all circumstances; or - Conditional: meaning that the requirement is dependent on the manufacturer having chosen to support optional functionality defined within the schedule. in the case of Conditional requirements,

28、it associates the requirement with the particular optional service or functionality; it qualifies each test procedure to be either: - Essential: meaning that it is included with the Essential Radio Test Suite and therefore the requirement shall be demonstrated to be met in accordance with the refere

29、nced procedures; - Other: meaning that the test procedure is illustrative but other means of demonstrating compliance with the requirement are permitted. Table A.1: HS Requirements and conformance Test specifications Table (HS-RTT) Harmonized Standard EN 302 998-2 The following requirements and test

30、 specifications are relevant to the presumption of conformity under the article 3.2 of the R those designated “O“ make up the Other Test Suite; for those designated “X“ there is no test specified corresponding to the requirement. The completion of all tests classified “E“ as specified with satisfact

31、ory outcomes is a necessary condition for a presumption of conformity. Compliance with requirements associated with tests classified “O“ or “X“ is a necessary condition for presumption of conformity, although conformance with the requirement may be claimed by an equivalent test or by manufacturers a

32、ssertion supported by appropriate entries in the technical construction file. Clause Number Identification of clause(s) defining the test specification in the present document unless another document is referenced explicitly. Where no test is specified (that is, where the previous field is “X“) this

33、 field remains blank. ETSI ETSI EN 302 998-2 V1.1.1 (2011-05) 13Annex B (informative): The EN title in the official languages The enlargement of the European Union (EU) resulted in a requirement from the EU for a larger number of languages for the translation of the titles of Harmonized Standards an

34、d mandated ENs that are to be listed in the Official Journal to support the implementation of this legislation. For this reason the title translation concerning the present document can be consulted via the e-approval application. ETSI ETSI EN 302 998-2 V1.1.1 (2011-05) 14Annex C (informative): Bibl

35、iography Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC (EMC Directive). Directive 2006/95/EC of the European Parliament and of

36、the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (LV Directive). CENELEC EN 55011 (1998): “Industrial, scientific and medical (ISM) radio-frequency equipment - Radio disturbance character

37、istics - Limits and methods of measurement“. CENELEC EN 55022 (1998): “Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement“. ETSI TR 100 028 (all parts): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics“. ETSI ETSI EN 302 998-2 V1.1.1 (2011-05) 15History Document history V1.1.1 July 2010 Public Enquiry PE 20101109: 2010-07-12 to 2010-11-09 V1.1.1 March 2011 Vote V 20110520: 2011-03-21 to 2011-05-20 V1.1.1 May 2011 Publication