ETSI EN 301 997-1-2002 Tranmission and Multiplexing (TM) Multipoint Equipment Radio Equipment for Use in Multimedia Wireless Systems (MWS) in the Frequency Band 40 5 GHz to 43 5 GH.pdf

《ETSI EN 301 997-1-2002 Tranmission and Multiplexing (TM) Multipoint Equipment Radio Equipment for Use in Multimedia Wireless Systems (MWS) in the Frequency Band 40 5 GHz to 43 5 GH.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 301 997-1-2002 Tranmission and Multiplexing (TM) Multipoint Equipment Radio Equipment for Use in Multimedia Wireless Systems (MWS) in the Frequency Band 40 5 GHz to 43 5 GH.pdf（29页珍藏版）》请在麦多课文档分享上搜索。

1、ETSI EN 301 997-1 1.1.1 (2002-06) European Sfandard (Telecommunicafions series) Transmission and Multiplexing (TM); Multipoint equipment; Radio Equipment for use in Multimedia Wireless Systems (MWS) in the frequency band 40,5 GHz to 43,5 GHz; Part 1 : General requirements 2 ETSI EN 301 997-1 V1.l.l

2、(2002-06) Reference DENITM-04097 Keywords digital, DRRS, multimedia, multipoint, MWS, radio, RLL ETSI 650 Route des Lucioles F-O6921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 O0 Fax: +33 4 93 65 47 16 Siret No 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-p

3、rfecture de Grasse (06) No 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/w.etsi.orq The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such

4、versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject

5、to revision or change of status. Information on the current status of this and other ETSI documents is available at hp:l/partal.etsi.arltb/saslsaus.asp If you find errors in the present document, send your comment to: Cori vriaht Notifica tion No part may be reproduced except as authorized by writte

6、n permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards Institute 2002. All rights reserved. DECTTM, PLUGTESTSTMand UMTSTMare Trade Marks of ETSI registered for the benefit of its Members. TIPHONTM and the TIPHON logo are

7、 Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI 3 ETSI EN 301 997-1 V1.l.l (2002-06) Contents Intellectual Property Rights . .5 Foreword . 5 Introduc

8、tion . .5 1 2 3 3.1 3.2 3.3 4 4.1 4.2 4.2.1 4.2.2 4.3 4.4 4.4.1 4.4.2 4.5 4.6 4.7 4.8 4.8.1 4.8.2 4.8.3 5 5.1 5.2 5.3 5.4 5.5 5.5.1 5.5.2 5.5.2.1 5.5.2.2 5.5.3 5.5.3.1 5.5.3.2 5.5.4 5.5.4.1 5.5.4.2 5.5.5 5.5.6 5.6 5.6.1 5.7 1 Scope 6 ieferences . .6 Iefinitions, symbols and abbreviations . 1 O Defin

9、itions 10 Symbols 10 Abbreviations . 10 3xeral characteristics . 11 General system architecture 11 Frequency bands and channel arrangements . 12 Frequency plan . 12 Channel arrangements . . 13 Compatibility requirements 13 Environmental conditions . . 13 Equipment within weather protected 1 . 13 Pow

10、er supply . 13 EMC conditions. . . 13 Synchronization of interface bit rates . . 14 Antenna/feeder/branching requirements . . 14 Antenna requirements . . 14 Return loss 14 Intermodulation products 14 System parameters 14 . Equipment for non-weather protected . 14 . 14 . 15 . 15 15 . 16 Power control

11、 . 16 Automatic Transnit Power Control (ATPC) . 16 Remote Transmit Power Control (RTPC) . . 16 Remote Frequency Control (RFC) . 16 Out ofblock emissions caused by RFC setting . . 16 Emissions caused by RFC setting inside the block. . 16 RF spectrum mask . 17 Channel spectrum mask . 17 Transmitter bl

12、ock edge mask . 17 Spurious emissions (external) . . 17 RF tolerance . 17 Receiver characteristics. . . 18 Spurious emissions (external) . 18 System performances . 18 s. 6 Types of interface . 18 Intra-block minimum requirements 20 Channel spectrum mask 20 BER as a function of Receiver input Signal

13、Level (RSL) . .2O Annex A (normative): A. 1 A.2 ETSI 4 ETSI EN 301 997-1 V1.l.l (2002-06) A.3 Co-channel interference . 20 A.4 Adjacent channel interference 21 Annex B (informative): CEPT/ERC regulatory considerations on EIRP and block edge mask 22 B . 1 General considerations . 22 B . 2 Transmitter

14、 maximum EIRP limits 22 B.3 Transmitter EIRP spectral density block mask 23 Annex C (informative): C . 1 Annex D (informative): Matched receiver block-edge selectivity mask 25 Receiver block-edge selectivity mask 25 Example of a method for Automatic Transmit Power Control (ATPC) in the uplink direct

15、ion . 27 History 29 ETSI 5 ETSI EN 301 997-1 V1.l.l (2002-06) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-member

16、s, and can be found in ETSI SR O00 3 14: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notijied to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (5). Pursuant to the ETSI IPR Pol

17、icy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR O00 3 14 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Eu

18、ropean Standard (Telecommunications series) has been produced by ETSI Technical Committee Transmission and Multiplexing (TM). The present document is part 1 of a multi-part deliverable covering Transmission and Multiplexing (TM); Multipoint equipment; Radio Equipment for use in Multimedia Wireless S

19、ystems (MWS) in the frequency band 40,5 GHz to 43,5 GHz, as identified below: Part 1: “General requirements“; Part 2: “Essential requirements under article 3.2 of the Directive 1999/5/EC“. National transposition dates Date of adoption of this EN: Date of latest announcement of this EN (doa): Date of

20、 latest publication of new National Standard or endorsement of this EN (dop/e): Date of withdrawal of any conflicting National Standard (dow): 3 1 May 2002 3 1 August 2002 28 February 2003 28 February 2003 Introd U ction The 40 GHz band has been identified and designated within CEPT with a CEPT/ERC/

21、DEC(99)15 5 on the designation of the harmonized frequency band 40,5 GHZ to 43,5 GHz for the introduction of Multimedia Wireless Systems (MWS), including MVDS. The term “Multimedia Wireless Systems“ has been introduced to cater for the phenomenon of convergence between terrestrial Fixed Service (FS)

22、 and Broadcasting Service (BS) applications, whereby distributors of entertainment services (broadcasters) are wishing to provide interactive services and telecommunications operators are wishing to supply broader band two-way services to wider markets. Multimedia Wireless Systems are wireless syste

23、ms, which support information exchange of more than one type, such as text, graphics, voice, sound, image, data and video. They are also defiied as terrestrial multipoint systems which have their origin in telecommunication andor broadcasting, and which provide fixed wireless access direct to the en

24、d user for multimedia services. These MWS may offer different degrees of interactivity, including purely distribution systems, such as digital MVDS. ETSI 6 ETSI EN 301 997-1 V1.l.l (2002-06) 1 Scope The present document specifies the minimum requirements for equipment and system parameters, includin

25、g parameters necessary to plan Co-existence, of MWS (Multimedia Wireless Systems) operating in the 40,5 GHz to 43,5 GHz frequency band and used for a range of applications including telecommunication and entertainment services. When MWS equipment is not intended for telecommunication purposes (e.g.

26、for entertainment services), different requirements related to, for example, environmental conditions (see clause 4.4), power supply (see clause 4.5) and synchronization interfaces (see clause 4.7), may be applied, provided that guaranteed values of parameters necessary for Co-existence with other M

27、WS systems are met. The present document is applicable to system and equipment parameters required to be able to plan the radio inter-operator Co-existence of a number of possible solutions for implementing MWS in the 40 GHz frequency band according the CEPT/ERC regulatory frame based on CEPT/ERC/DE

28、C(99)15 5 and CEPT/ECC/REC 01-04 55. Besides specifically designed multipoint Fixed Digital Radio Systems (FDRS) like that in the scope of ETSI Project (EP) BRAN, some other solutions, derived from standardized technology, are already documented, and include systems that align with: EN 300 748 i; EN

29、301 199 2; ITU-R Recommendation F.1499 3; IEEE 802.16 56. It is likely that the frequency assignment criteria in this band will be based on “frequency blocks“ according to CEPT/ECC/REC O 1-04 55, therefore the radio frequency Co-ordination parameters specified in the present document may be subdivid

30、ed into two categories: those detailed in the present document, related to the minimum requirements for frequency Co-ordination of various systems deployed by an operator inside the same block of frequency. Although these are not all regarded as “essential R those related to adjacent “block-edge“ in

31、terference control; these will be considered as “essential requirements“ for the application of Directive 1999/5/EC (R Multipoint Video Distribution Systems (MVDS) at 10 GHz and above“. ETSI EN 301 199: “Digital Video Broadcasting (DVB); Interaction channel for Local Multi-point Distribution Systems

32、 (LMDS)“. ITU-R Recommendation F. 1499: “Radio transmission systems for fixed broadband wireless access based on cable modem standard“. 21 31 ETSI 7 ETSI EN 301 997-1 V1.l.l (2002-06) 41 51 71 Directive 1999/5/EC: “of the European Parliament and of the Council of 9 March 1999 on radio equipment and

33、telecommunications terminal equipment and the mutual recognition of their conformity (R Point to Multipoint Antennas; Antennas for point-to-multipoint fixed radio systems in the 11 GHz to 60 GHz band; Part 3: Multipoint Multimedia Wireless system in 40,5 GHz to 43,5 GHz“. ETSI EN 300 O 19: “Equipmen

34、t Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment“. ETSI EN 300 385: “Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for fixed radio links and ancillary equipment“. ITU-T Recommendation

35、G. 8 10: “Definitions and terminology for synchronization networks“. ITU-T Recommendation G.812: “Timing requirements of slave clocks suitable for use as node clocks in synchronization networks“. ITU-T Recommendation G.823: “The control of jitter and wander within digital networks which are based on

36、 the 2 048 kbit/s hierarchy“. ITU-T Recommendation G. 8 13 : “Timing characteristics of SDH equipment slave clocks (SEC)“ ITU-T Recommendation G. 825: “The control of jitter and wander within digital networks which are based on the synchronous digital hierarchy (SDH)“. ITU-T Recommendation G.703 : “

37、Physical/electrical characteristics of hierarchical digital interfaces“. ITU-T Recommendation G. 13 1 : “Control of talker echo“. ITU-T Recommendation G.7 1 1 : “Pulse code modulation (PCM) of voice frequencies“ ITU-T Recommendation G.726: “40, 32,24, 16 kbit/s adaptive differential pulse code modul

38、ation (ADPCM)“. ITU-T Recommendation G.728: “Coding of speech at 16 kbit/s using low-delay code excited linear prediction“. ITU-T Recommendation G.729: “Coding of speech at 8 kbit/s using conjugate-structure algebraic-code- excited linear-prediction (CS-ACELP)“ . ITU-T Recommendation Q.552: “Transmi

39、ssion characteristics at 2-wire analogue interfaces of digital exchange“. ITU-T Recommendation Q.553 : “Transmission characteristics at 4-wire analogue interfaces of digital exchanges“. ITU-T Recommendation V series: “Data communication over the telephone network“. ITU-T Recommendation X series: “Da

40、ta networks and open system communication“. ITU-T Recommendation G.96 1 : “Digital transmission system on metallic local lines for ISDN basic rate access“. ETSI ETS 300 O 12: “Integrated Services Digital Network (ISDN); Basic user-network interface; Layer 1 specification and test principles“. ETSI E

41、TS 300 O1 1: “Integrated Services Digital Network (ISDN); Primary rate user-network interface; Layer 1 specification and test principles“. ITU-T Recommendation G.962: “Access digital section for ISDN primary rate at 2 048 kbit/s“. ETSI 8 ETSI EN 301 997-1 V1.l.l (2002-06) i281 i291 i301 i3 i1 i321 i

42、331 i341 i351 i3 61 i3 81 i371 i3 91 i401 i411 i421 i43 1 i441 i451 i461 i471 i481 i491 ITU-T Recommendation G.707: “Network node interface for the synchronous digital hierarchy (SDH)“. ITU-T Recommendation G.964: “V-Interfaces at the digital local exchange (LE) - V5.1 interface (Based on 2 048 kbit

43、/s) for the support of access network (AN)“. ITU-T Recommendation G.965: “V-Interfaces at the digital local exchange (LE) - V5.2 interface (based on 2 048 kbit/s) for the support of access network (AN)“. ITU-T Recommendation G.957: “Optical interfaces for equipments and systems relating to the synch

44、ronous digital hierarchy“. ETSI EN 300 324: “V interfaces at the digital Local Exchange (LE); V5.1 interface for the support of Access Network (AN)“. ETSI EN 300 347: “V interfaces at the digital Local Exchange (LE); V5.2 interface for the support of Access Network (AN)“. ETSI ETS 300 132-1: “Equipm

45、ent Engineering (EE); Power supply interface at the input to telecommunications equipment; Part 1 : Operated by alternating current (ac) derived from direct current (dc) sources“. ETSI EN 300 132-2: “Environmental Engineering (EE); Power supply interface at the input to telecommunications equipment;

46、 Part 2: Operated by direct current (dc)“. CEPT/ERC/REC 74-0 1 : “Spurious emissions“. EN 60950: “Safety of information technology equipment“ ITU-T Recommendation G.704: “Synchronous frame structures used at 1 544,6 3 12,2 048, 8 448 and 44 736 kbit/s hierarchical levels“. ANSI/ IEEE 802.3 : “Inform

47、ation Technology - Telecommunication Access networks for residential customers“. ETSI EN 301 390: “Fixed Radio Systems; Point-to-point and Point-to-Multipoint Systems Spurious emissions and receiver immunity at equipment/antenna port of Digital Fixed Radio Systems“. ITU-T Recommendation G.723.1: “Sp

48、eech coders: Dual rate speech coder for multimedia communications transmitting at 5.3 and 6.3 kbit/s“. ETSI EN 301 489-1 : “Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1 : Common technical require

49、ments“. ETSI EN 301 489-4: “Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 4: Specific conditions for fixed radio links and ancillary equipment and services“. ITU-R Recommendation F. 1399-1 : “Vocabulary of terms for wireless access“. ETSI EN 301 213-1 : “Fixed Radio Systems; Point-to-multipoint equipment; Point-to-multipoint digital radio systems in frequency bands in the range 24,25 GHz to 29,5 GHz using different access methods; Part 1: Basic paramete