ETSI EN 301 843-1-2016 ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services Harmonised Standard covering the essential requirements of article 3 1b .pdf

《ETSI EN 301 843-1-2016 ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services Harmonised Standard covering the essential requirements of article 3 1b .pdf》由会员分享，可在线阅读，更多相关《ETSI EN 301 843-1-2016 ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services Harmonised Standard covering the essential requirements of article 3 1b .pdf（31页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 301 843-1 V2.1.1 (2016-03) ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services; Harmonised Standard covering the essential requirements of article 3.1b of the Directive 2014/53/EU; Part 1: Common technical requirements HARMONISED EUROPEAN STANDARD ETSI ETSI

2、EN 301 843-1 V2.1.1 (2016-03) 2 Reference REN/ERM-EMC-347 Keywords EMC, harmonised standard, maritime, radio ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistr

3、e la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present documen

4、t shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within

5、ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present

6、document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized b

7、y written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTST

8、M, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ET

9、SI ETSI EN 301 843-1 V2.1.1 (2016-03) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 7g33 Definitions, symbols and abbreviations . 8g33.1 Definitions 8g33.2 Symbols 9g33.3 Abbrevi

10、ations . 9g34 General and operational requirements 10g34.1 Environmental profile . 10g34.2 Arrangements for test signals . 10g34.2.0 General 10g34.2.1 Arrangements for test signals at the input of transmitters . 10g34.2.2 Arrangements for test signals at the output of transmitters . 11g34.2.3 Arrang

11、ements for test signals at the input of receivers . 11g34.2.4 Arrangements for test signals at the output of receivers . 11g34.2.5 Arrangements for testing transmitter and receiver together (as a system) 12g34.3 RF exclusion band of radio communications equipment 12g34.4 Narrow band responses of rec

12、eivers or receivers which are part of transceivers . 13g34.5 Normal test modulation 13g35 Performance assessment . 13g35.1 General . 13g35.2 Equipment which can provide a continuous communication link 14g35.3 Equipment which does not provide a continuous communication link 14g35.4 Ancillary equipmen

13、t . 15g35.5 Equipment classification 15g36 Performance criteria . 15g36.0 General requirements . 15g36.1 Performance criteria A for continuous phenomena applied to transmitters and receivers 16g36.2 Performance criteria B for transient phenomena applied to transmitters and receivers . 16g36.3 Perfor

14、mance criteria C applied to power supply failure . 16g36.4 Performance check . 17g36.5 Performance criteria for equipment which does not provide a continuous communication link 17g36.6 Performance criteria for ancillary equipment tested on a stand alone basis . 17g37 Applicability overview tables .

15、17g37.0 General . 17g37.1 EMC emission 18g37.2 Immunity 18g38 Testing for compliance with technical requirements 18g38.0 Environmental conditions for testing . 18g38.1 Test configuration. 18g38.2 Enclosure of ancillary equipment measured on a stand alone basis . 19g38.2.0 Applicability . 19g38.2.1 T

16、est description . 19g38.2.2 Test method 19g38.2.3 Limits 20g38.3 DC power input/output ports 20g38.3.0 Applicability . 20g38.3.1 Test description . 20g3ETSI ETSI EN 301 843-1 V2.1.1 (2016-03) 4 8.3.2 Test method 20g38.3.3 Limits 21g38.4 AC mains power input/output ports . 21g38.4.0 Applicability . 2

17、1g38.4.1 Test description . 22g38.4.2 Test method 22g38.4.3 Limits 22g39 Test methods and levels for immunity tests . 22g39.0 General . 22g39.1 Test configuration. 22g39.2 Radio frequency electromagnetic field (80 MHz to 2 700 MHz) . 23g39.2.0 Applicability . 23g39.2.1 Test description . 23g39.2.2 T

18、est method 23g39.2.3 Performance criteria 24g39.3 Electrostatic discharge 24g39.3.0 Applicability . 24g39.3.1 Test description . 24g39.3.2 Test method 24g39.3.3 Performance criteria 24g39.4 Fast transients, differential and common mode 25g39.4.0 Applicability . 25g39.4.1 Test description . 25g39.4.2

19、 Test method 25g39.4.3 Performance criteria 25g39.5 Radio frequency, common mode 25g39.5.0 Applicability . 25g39.5.1 Test description . 26g39.5.2 Test method 26g39.5.3 Performance criteria 26g39.6 Power supply variations . 26g39.6.0 Applicability . 26g39.6.1 Power supply short term variations . 27g3

20、9.6.1.1 Test description . 27g39.6.1.2 Test method . 27g39.6.1.3 Performance criteria 27g39.6.2 Power supply failure . 27g39.6.2.1 Test description . 27g39.6.2.2 Test method . 27g39.6.2.3 Performance criteria 27g39.7 Surges . 27g39.7.0 Applicability . 27g39.7.1 Test description . 28g39.7.2 Test meth

21、od 28g39.7.3 Performance criteria 28g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 29g3History 31g3ETSI ETSI EN 301 843-1 V2.1.1 (2016-03) 5 Intellectual Property Rights IPRs essential or potentially essential to the present

22、document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respec

23、t of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of ot

24、her IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Ma

25、tters (ERM). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.10 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making av

26、ailable on the market of radio equipment and repealing Directive 1999/5/EC i.4. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the sc

27、ope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 1 of a multi-part deliverable covering the ElectroMagnetic Compatibility (EMC) standard for marine radio equipment a

28、nd services, as identified below: Part 1: “Common technical requirements“; Part 2: “Specific conditions for VHF radiotelephone transmitters and receivers“; Part 4: “Specific conditions for Narrow-Band Direct-Printing (NBDP) NAVTEX receivers“; Part 5: “Specific conditions for MF/HF radiotelephone tra

29、nsmitters and receivers“; Part 6: “Specific conditions for Earth Stations on board Vessels operating in frequency bands above 3 GHz“. National transposition dates Date of adoption of this EN: 21 March 2016 Date of latest announcement of this EN (doa): 30 June 2016 Date of latest publication of new N

30、ational Standard or endorsement of this EN (dop/e): 31 December 2016 Date of withdrawal of any conflicting National Standard (dow): 31 December 2017 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“

31、 are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 301 843-1 V2.1.1 (2016-03) 6 1 Scope The present document contain

32、s the common requirements for marine radio communications equipment and associated ancillary equipment, in respect of ElectroMagnetic Compatibility (EMC). The provisions of the present document apply to marine radio equipment not covered in the scope of the Council Directive on marine equipment (the

33、 “Marine Equipment Directive“ 96/98/EC i.5). Product dependent arrangements necessary to perform the EMC tests on dedicated types of marine radio communications equipment, and the assessment of test results, are detailed in the appropriate product related parts of the present document. The present d

34、ocument, together with the product related part, specifies the applicable EMC tests, the methods of measurement, the limits and the performance criteria for marine radio equipment and associated ancillary equipment. In case of differences (for instance concerning special conditions, definitions, abb

35、reviations) between the present document and the relevant product related part of the present document, the product related part takes precedence. For the further content of the present document, the expression “radio equipment“ is taken to mean marine radio communications equipment, in each individ

36、ual case. Technical specifications related to the antenna port of radio equipment and emissions from the enclosure port of radio equipment and combinations of radio and associated ancillary equipment are not included in the present document. Such technical specifications are normally found in the re

37、levant product standards for the effective use of the radio spectrum. The environment classification used in the present document is maritime, as defined in CENELEC EN 60945 1. Marine radio communications equipment meeting the EMC requirements set out in CENELEC EN 60945 1 is deemed to meet also the

38、 EMC requirements for the residential, commercial and light industrial environment as defined in CENELEC EN 61000-6-3 i.1 and CENELEC EN 61000-6-1 i.2. The EMC requirements have been selected to ensure an adequate level of compatibility for apparatus intended to be used in the maritime environment.

39、The levels, however, do not cover extreme cases which may occur in any location but with low probability of occurrence. Compliance of radio equipment to the requirements of the present document does not signify compliance to any requirements related to spectrum management or to the use of the equipm

40、ent (licensing requirements). Compliance to the requirements of the present document does not signify compliance to any safety requirements. However, it is the responsibility of the assessor of the equipment to record in the test report any observations regarding the test sample becoming dangerous o

41、r unsafe as a result of the application of the tests called for in the present document. The present document contains requirements to demonstrate an adequate level of electromagnetic compatibility as set out in Directive 2014/30/EU. In addition to the present document, other ENs that specify techni

42、cal requirements in respect of essential requirements under other parts of article 3 of the Radio Equipment Directive i.4 may apply to equipment within the scope of the present document. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or ed

43、ition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected l

44、ocation might be found at http:/docbox.etsi.org/Reference. ETSI ETSI EN 301 843-1 V2.1.1 (2016-03) 7 NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the appl

45、ication of the present document. 1 CENELEC EN 60945:2002 + Corrigendum 1 (2008): “Maritime navigation and radiocommunication equipment and systems - General requirements - Methods of testing and required test results“. 2 CISPR 16-1-1 (2015): “Specification for radio disturbance and immunity measurin

46、g apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus“. 3 CENELEC EN 61000-4-2 (2003): “Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test“. 4 CENELEC EN 61000-4-3 (2006 + A

47、mendment 1:2008 +Amendment 2:2010): “Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test“. 5 CENELEC EN 61000-4-4 (2012): “Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement technique

48、s - Electrical fast transient/burst immunity test“. 6 CENELEC EN 61000-4-5 (2014): “Electromagnetic compatibility (EMC) - Part 4-5: Testing and measurement techniques - Surge immunity test“. 7 CENELEC EN 61000-4-6 (2014): “Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techn

49、iques - Immunity to conducted disturbances, induced by radio-frequency fields“. 8 ETSI EN 301 843-2 (V2.1.1) (03-2016): “ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services; Harmonised Standard covering the essential requirements of article 3.1b of the Directive 2014/53/EU; Part 2: Specific conditions for VHF radiotelephone transmitters and receivers“. 9 ETSI EN 301 843-4 (V2.1.1) (03-2016): “ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services; Harmonised Standard covering the